ReferenceDesignLibrary

Refine Search

Eval Board Voltage In Topology Current Out Voltage Out (Max) Outputs and Type Efficiency @ Conditions Features Switching Frequency Component Count + Extras Design Author Application / Target Market
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear All Selections Apply Filters

Designs (149)

149 Results - Page 1/15 |< < 1 2 3 4 5 > >|

TPS61150EVM-150: 4 LEDs x 2 @ 15mA, 2.5 ~ 6V in

Manufacturer: Texas Instruments

The Texas Instruments TPS61150EVM-150 evaluation module contains the TPS61150 IC. This EVM provides two independently regulated current outputs using a single inductor step-up (boost) converter.

View Design

EVL6562A-LED: 350mA @ 45V Max, 36 ~ 60V in

Manufacturer: STMicroelectronics

Whenever a lighting application, such as street lighting for example, requires an elevated number of LEDs, there are basically two solutions: the first is to connect all the diodes in series in a single "string"; the second is to place several strings in parallel with fewer elements in each one.

View Design

LM3409HVEVAL: 1.5A @ 42V Max, 48V in

Manufacturer: Texas Instruments

This evaluation board showcases the LM3409HV PFET controller for a buck current regulator. It is designed to drive 12 LEDs (VO = 42V) at a maximum average LED current (ILED = 1.5A) from a DC input voltage (VIN = 48V). The switching frequency (fSW = 400 kHz) is targeted for the nominal operating point, however fSW varies across the entire operating range.

View Design

ZXSC400 DN67: 1 LED @ 350mA, 1.8 ~ 3Vin

Manufacturer: Diodes Incorporated

The ZXSC400, although designed for small LEDs in LCD backlighting, is sufficiently flexible to provide an efficient 1W solution producing a nominal 350mA constant current source from 2 NiMH or NiCd cells.

View Design

ZXSC310 DN69: 4 LEDs @ 40mA in Par / 1 LED @ 160mA

Manufacturer: Diodes Incorporated

This design note shows a typical ZXSC310 LED driver circuit for a solar power garden light. The input voltage ranges from 1.7V to 2.5V with a maximum output current of 160mA at 2.4V input.

View Design

ZXLD1350 AN48: 2 LEDs @ 700mA, 12 ~ 30 Vin

Manufacturer: Diodes Incorporated

The ZXLD1350 is a continuous mode inductive step-down converter, designed for driving single or multiple series connected LEDs efficiently from a voltage source higher than the LED voltage. The device operates from an input supply between 7V and 30V and provides an externally adjustable output current of up to 350mA.

View Design

CAT4201AGEVB: 350mA @ 20V Max, 6.5 ~ 28V in

Manufacturer: ON Semiconductor

The CAT4201 is a high efficiency step-down LED driver from Catalyst Semiconductor. This device is designed to drive high brightness LEDs up to 350mA from a power supply up to 28V. The LED brightness is controlled by a single resistor from the RSET pin to GND. Analog dimming and idle mode control are available through the CTRL input. An external circuit is provided on the CAT4201AEVB for PWM dimmin…

View Design

STEVAL-ILL008V1: 1 LED @ 280mA, 0.6 ~ 5.5V in

Manufacturer: STMicroelectronics

The L6920D is used in this flashlight application as it is a high efficiency step-up controller that realizes the conversion from battery voltage to the selected output voltage with only three external components.

View Design

LM3404HVEVAL: 1A @ Vin Max, 6 ~ 75V in

Manufacturer: Texas Instruments

The LM3404HV circuit and BOM have been designed to provide a constant forward current of 1.0A to a single LED with a forward voltage of approximately 3.7V from an input of 48V ±10%. Over the input voltage range of 6V to 75V the average LED current, IF, is 1.0A ±10%, the ripple current, ΔiF, will not exceed 400 mAP-P, and the switching frequency is 200 kHz ± 10%.

View Design

ZXSC400EV4: 1 LED @ 350mA, 1.8 ~ 3 Vin

Manufacturer: Diodes Incorporated

The ZXSC400 is voltage mode boost converter in SOT23-6 package. Its low feedback voltage allows the current in a chain of LEDs to be set and accurately monitored with a single resistor with minimal losses. The ZXSC400EV4 is configured as a boost converter to drive a 1W LED from two NiCd / NiMH batteries.

View Design
149 Results - Page 1/15 |< < 1 2 3 4 5 > >|