NS Series Catalog Datasheet by Taiyo Yuden

View All Related Products | Download PDF Datasheet
Product Inlormallcm m mus cala‘og \s as a! wmp‘antab‘e medlea‘ devices ‘ TAIYD YUDEN 2021
2
21
This catalog contains the typical speci cation only due to the limitation of space. When you consider the purchase of our products, please check our product speci cation sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
for General Electronic Equipment
REMINDERS
Notice for TAIYO YUDEN products
Please read this notice before using the TAIYO YUDEN products.
Product Information in this Catalog
Product information in this catalog is as of October 2020. All of the
contents specified herein and production status of the products listed in
this catalog are subject to change without notice due to technical
improvement of our products, etc. Therefore, please check for the latest
information carefully before practical application or use of our products.
Please note that TAIYO YUDEN shall not be in any way responsible
for any damages and defects in products or equipment incorporating
our products, which are caused under the conditions other than those
specified in this catalog or individual product specification sheets.
Approval of Product Specifications
Plea se contac t TAIYO YUDEN for fur the r details of p rodu ct
specifications as the individual product specification sheets are
available. When using our products, please be sure to approve our
product specifications or make a written agreement on the product
specification with TAIYO YUDEN in advance.
Pre-Evaluation in the Actual Equipment and Conditions
Please conduct validation and verification of our products in actual
conditions of mounting and operating environment before using our
products.
Limited Application
1. Equipment Intended for Use
The p roducts liste d in thi s cat alog are in te nde d for gene ral -
purpose and standard use in general electronic equipment (e.g.,
AV equipment, OA equipment, home electric appliances, office
equipment, information and communication equipment including,
without limitation, mobile phone, and PC) and other equipment
specified in this catalog or the individual product specification sheets.
TAIYO YUDEN has the line-up of the products intended for
use in automotive electronic equipment, telecommunications
infrastructure and industrial equipment, or medical devices
classified as GHTF Classes A to C (Japan Classes I to III).
Therefore, when using our p roducts for these e quipm ent,
please check available applications specified in this catalog
or the individual product specification sheets and use the
corresponding products.
2. Equipment Requiring Inquiry
Please be sure to contact TAIYO YUDEN for further information
before using the products listed in this catalog for the following
equipment (excluding intended equipment as specified in this
catalog or the individual product specification sheets) which may
cause loss of human life, bodily injury, serious property damage
and/or serious public impact due to a failure or defect of the
products and/or malfunction attributed thereto.
(1) Transportation equipment (automotive powertrain control
system, train control system, and ship control system, etc.)
(2) Traffic signal equipment
(3) Disaster prevention equipment, crime prevention equipment
(4) Medical devices classified as GHTF Class C (Japan Class III)
(5) Highly public information network equipment, data-
processing equipment (telephone exchange, and base
station, etc.)
(6) Any other equipment requiring high levels of quality and/or
reliability equal to the equipment listed above
3. Equipment Prohibited for Use
Please do not incorporate our products into the following
equipment requiring extremely high levels of safety and/or
reliability.
(1) Aerospace equipment (artificial satellite, rocket, etc.)
(2) Aviation equipment *1
(3) Medical devices classified as GHTF Class D (Japan Class IV),
implantable medical devices *
2
(4) Power generation control equipme nt (nuc lea r power,
hydroelectric power, thermal power plant control system, etc.)
(5) Undersea equipment (submarine repeating equipment,
underwater work equipment, etc.)
(6) Military equipment
(7) Any other equipment requiring extremely high levels of safety
and/or reliability equal to the equipment listed above
*Notes:
1. There is a possibility that our products can be used only
for aviation equipment that does not directly affect the safe
operation of aircraft (e.g., in-flight entertainment, cabin
light, electric seat, cooking equipment) if such use meets
requirements specified separately by TAIYO YUDEN. Please
be sure to contact TAIYO YUDEN for further information
before using our products for such aviation equipment.
2. Implantable medical devices contain not only internal unit
which is implanted in a body, but also external unit which is
connected to the internal unit.
4. Limitation of Liability
Please note that unless you obtain prior written consent of TAIYO
YUDEN, TAIYO YUDEN shall not be in any way responsible for
any damages incurred by you or third parties arising from use of
the products listed in this catalog for any equipment that is not
intended for use by TAIYO YUDEN, or any equipment requiring
inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN
as described above.
Safety Design
When using our products for high safety and/or reliability-required
equipment or circuits, please fully perform safety and/or reliability
evaluation. In addition, please install (i) systems equipped with
a protection circuit and a protection device and/or (ii) systems
equipped with a redundant circuit or other system to prevent an
unsafe status in the event of a single fault for a failsafe design to
ensure safety.
Intellectual Property Rights
Information contained in this catalog is intended to convey examples
of typical performances and/or applications of our products and is
not intended to make any warranty with respect to the intellectual
property rights or any other related rights of TAIYO YUDEN or any
third parties nor grant any license under such rights.
Limited Warranty
Please note that the scope of warranty for our products is limited to
the delivered our products themselves and TAIYO YUDEN shall not
be in any way responsible for any damages resulting from a failure
or defect in our products. Notwithstanding the foregoing, if there is
a written agreement (e.g., supply and purchase agreement, quality
assurance agreement) signed by TAIYO YUDEN and your company,
TAIYO YUDEN will warrant our products in accordance with such
agreement.
TAIYO YUDENs Official Sales Channel
The contents of this catalog are applicable to our products which are
purchased from our sales offices or authorized distributors (hereinafter
TAIYO YUDENs official sales channel). Please note that the contents
of this catalog are not applicable to our products purchased from any
seller other than TAIYO YUDENs official sales channel.
Caution for Export
Some of our products listed in this catalog may require specific
procedures for export according to U.S. Export Administration
Regulations, Foreign Exchange and Foreign Trade Control Law
of Japan, and other applicable regulations. Should you have any
questions on this matter, please contact our sales staff.
January 2021. All of the
64
21
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
for General Electronic Equipment
SMD POWER INDUCTORS(NS SERIES)
i_smd_NS_e-E08R01.doc
SMD POWER INDUCTORSNS SERIES
REFLOW
PARTS NUMBER * Operating Temp.:-40~+125℃(Including self-generated heat
N
S
1
0
1
4
5
T
1
0
0
M
N
A
△=Blank space
①Series name
Code Series name
NS△ Shielded specification
②Dimensions(L×W×H)
Code Dimensions(L×W×H)[mm]
10145 10.1×10.1×4.5
10155 10.1×10.1×5.5
10165 10.1×10.1×6.5
12555 12.5×12.5×5.5
12565 12.5×12.5×6.5
12575 12.5×12.5×7.5
③Packaging
Code Packaging
T△ Taping
④Nominal inductance
Code
(example) Nominal inductance[μH]
1R0 1.0
100 10
101 100
※R=Decimal point
⑤Inductance tolerance
Code Inductance tolerance
M ±20%
N ±30%
⑥Internal code
Code
N△ Internal code
NA
STANDARD EXTERNAL DIMENSIONS / MINIMUM QUANTITY
W
L
a
bb
H
The NS 101□ type does not have the indication of the Manufacturing date code.
Type L W H a b Minimum quantity [pcs
NS 10145 10.1±0.3
(0.398±0.012)
10.1±0.3
(0.398±0.012)
4.5±0.35
(0.177±0.014)
2.8±0.1
(0.110±0.004)
2.0±0.15
(0.079±0.006) 2000
NS 10155 10.1±0.3
(0.398±0.012)
10.1±0.3
(0.398±0.012)
5.5±0.35
(0.217±0.014)
2.8±0.1
(0.110±0.004)
2.0±0.15
(0.079±0.006) 2000
NS 10165 10.1±0.3
(0.398±0.012)
10.1±0.3
(0.398±0.012)
6.5±0.35
(0.256±0.014)
2.8±0.1
(0.110±0.004)
2.0±0.15
(0.079±0.006) 2000
NS 12555 12.5±0.3
(0.492±0.012)
12.5±0.3
(0.492±0.012)
5.5±0.35
(0.217±0.014)
3.0±0.1
(0.118±0.004)
2.0±0.15
(0.079±0.006) 2000
NS 12565 12.5±0.3
(0.492±0.012)
12.5±0.3
(0.492±0.012)
6.5±0.35
(0.256±0.014)
3.0±0.1
(0.118±0.004)
2.0±0.15
(0.079±0.006) 2000
NS 12575 12.5±0.3
(0.492±0.012)
12.5±0.3
(0.492±0.012)
7.5±0.35
(0.295±0.014)
3.0±0.1
(0.118±0.004)
2.0±0.15
(0.079±0.006) 2000
Unit:mm(inch)
Recommended Land Patterns
Surface Mounting
・Mounting and soldering conditions should be checked beforehand.
・Applicable soldering process to these products is reflow soldering only.
AA
B
C
Type A B C
NS 10145 2.5 5.6 3.2
NS 10155 2.5 5.6 3.2
NS 10165 2.5 5.6 3.2
NS 12555 2.5 8.6 3.2
NS 12565 2.5 8.6 3.2
NS 12575 2.5 8.6 3.2
Unit:mm
POWER INDUCTORS
INDUCTORS
TAIYD YUDEN 2021
65
21
for General Electronic Equipment
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
PARTS NUMBER
NS 10145 type
Saturation current
Idc1
Temperature rise current
Idc2
NS 10145T 1R0NNA RoHS 1.0 ±30% 0.0049 12.54 8.90 100
NS 10145T 1R5NNA RoHS 1.5 ±30% 0.0060 10.34 7.99 100
NS 10145T 2R2NNA RoHS 2.2 ±30% 0.0085 8.91 6.64 100
NS 10145T 3R3NNA RoHS 3.3 ±30% 0.0100 7.33 6.10 100
NS 10145T 4R7NNA RoHS 4.7 ±30% 0.0144 6.69 5.03 100
NS 10145T 5R6NNA RoHS 5.6 ±30% 0.0181 5.85 4.45 100
NS 10145T 6R8NNA RoHS 6.8 ±30% 0.0200 5.05 4.22 100
NS 10145T 100MNA RoHS 10 ±20% 0.0248 4.22 3.77 100
NS 10145T 150MNA RoHS 15 ±20% 0.0381 3.44 3.00 100
NS 10145T 220MNA RoHS 22 ±20% 0.0520 2.87 2.55 100
NS 10145T 330MNA RoHS 33 ±20% 0.0815 2.36 2.01 100
NS 10145T 470MNA RoHS 47 ±20% 0.100 1.85 1.80 100
NS 10145T 680MNA RoHS 68 ±20% 0.150 1.66 1.45 100
NS 10145T 101MNA RoHS 100 ±20% 0.200 1.29 1.25 100
NS 10145T 151MNA RoHS 150 ±20% 0.341 1.11 0.94 100
NS 10145T 221MNA RoHS 220 ±20% 0.485 0.91 0.78 100
NS 10145T 331MNA RoHS 330 ±20% 0.700 0.71 0.64 100
NS 10145T 471MNA RoHS 470 ±20% 1.030 0.61 0.52 100
NS 10145T 681MNA RoHS 680 ±20% 1.57 0.50 0.42 100
NS 10145T 102MNA RoHS 1000 ±20% 2.58 0.41 0.32 100
NS 10145T 152MNA RoHS 1500 ±20% 3.70 0.36 0.27 100
NS 10155 type
Saturation current
Idc1
Temperature rise current
Idc2
NS 10155T 1R5NNA RoHS 1.5 ±30% 0.0060 11.90 8.39 100
NS 10155T 2R2NNA RoHS 2.2 ±30% 0.0072 10.00 7.61 100
NS 10155T 3R3NNA RoHS 3.3 ±30% 0.0097 8.50 6.49 100
NS 10155T 4R7NNA RoHS 4.7 ±30% 0.0112 7.40 6.01 100
NS 10155T 6R8NNA RoHS 6.8 ±30% 0.0159 6.00 4.98 100
NS 10155T 100MNA RoHS 10 ±20% 0.0200 4.49 4.40 100
NS 10155T 150MNA RoHS 15 ±20% 0.0284 4.03 3.65 100
NS 10155T 220MNA RoHS 22 ±20% 0.0380 3.37 3.12 100
NS 10165 type
Saturation current
Idc1
Temperature rise current
Idc2
NS 10165T 1R5NNA RoHS 1.5 ±30% 0.0062 13.60 8.04 100
NS 10165T 2R2NNA RoHS 2.2 ±30% 0.0074 10.80 7.32 100
NS 10165T 3R3NNA RoHS 3.3 ±30% 0.0086 9.30 6.76 100
NS 10165T 4R7NNA RoHS 4.7 ±30% 0.0112 7.70 5.88 100
NS 10165T 6R8NNA RoHS 6.8 ±30% 0.0140 6.00 5.22 100
NS 10165T 100MNA RoHS 10 ±20% 0.0174 5.20 4.66 100
NS 10165T 150MNA RoHS 15 ±20% 0.0250 4.50 3.84 100
NS 10165T 220MNA RoHS 22 ±20% 0.0313 3.60 3.41 100
NS 12555 type
Saturation current
Idc1
Temperature rise current
Idc2
NS 12555T 6R0NN RoHS 6.0 ±30% 0.0140 5.01 5.60 100
NS 12555T 100MN RoHS 10 ±20% 0.0175 4.73 5.04 100
NS 12555T 150MN RoHS 15 ±20% 0.0233 3.89 4.18 100
NS 12555T 220MN RoHS 22 ±20% 0.0297 3.20 3.81 100
NS 12555T 330MN RoHS 33 ±20% 0.0415 2.64 3.16 100
NS 12555T 470MN RoHS 47 ±20% 0.0551 2.23 2.70 100
NS 12555T 680MN RoHS 68 ±20% 0.0797 1.81 2.14 100
NS 12555T 101MN RoHS 100 ±20% 0.117 1.53 1.86 100
NS 12555T 151MN RoHS 150 ±20% 0.176 1.22 1.43 100
NS 12555T 221MN RoHS 220 ±20% 0.270 1.00 1.18 100
NS 12555T 331MN RoHS 330 ±20% 0.410 0.82 0.96 100
NS 12555T 471MN RoHS 470 ±20% 0.520 0.68 0.80 100
NS 12555T 681MN RoHS 680 ±20% 0.760 0.60 0.72 100
NS 12555T 102MN RoHS 1000 ±20% 1.12 0.47 0.59 100
NS 12555T 152MN RoHS 1500 ±20% 1.73 0.40 0.44 100
※) The saturation current value (Idc1) is the DC current value having inductance decrease down to 30%. (at 20℃)
※) The temperature rise current value (Idc2) is the DC current value having temperature increase up to 40℃. (at 20℃)
※) The rated current is the DC current value that satisfies both of current value saturation current value and temperature rise current value.
Rated current ※) [A] Measuring frequency
[kHz]
Parts number EHS Nominal inductance
[μH] Inductance tolerance DC Resistance
[Ω](±20%)
Parts number EHS Nominal inductance
[μH] Inductance tolerance
Parts number EHS Nominal inductance
[μH] Inductance tolerance
Rated current ※) [A] Measuring frequency
[kHz]
DC Resistance
[Ω](±20%)
Rated current ※) [A] Measuring frequency
[kHz]
DC Resistance
[Ω](±20%)
DC Resistance
[Ω](±20%)
Rated current ※) [A] Measuring frequency
[kHz]
Parts number EHS Nominal inductance
[μH] Inductance tolerance
i_smd_NS_e-E08R01.xls
POWER INDUCTORS
INDUCTORS
TAIYD YUDEN 2021
66
21
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
for General Electronic Equipment
PARTS NUMBER
NS 12565 type
Saturation current
Idc1
Temperature rise current
Idc2
NS 12565T 2R0NN RoHS 2.0 ±30% 0.0080 13.91 7.60 100
NS 12565T 4R2NN RoHS 4.2 ±30% 0.0126 10.15 5.91 100
NS 12565T 7R0NN RoHS 7.0 ±30% 0.0162 7.93 5.21 100
NS 12565T 100MN RoHS 10 ±20% 0.0199 6.96 4.75 100
NS 12565T 150MN RoHS 15 ±20% 0.0237 5.84 4.33 100
NS 12565T 220MN RoHS 22 ±20% 0.0310 4.87 3.91 100
NS 12565T 330MN RoHS 33 ±20% 0.0390 3.89 3.22 100
NS 12565T 470MN RoHS 47 ±20% 0.0575 3.34 2.78 100
NS 12565T 680MN RoHS 68 ±20% 0.0775 2.78 2.30 100
NS 12565T 101MN RoHS 100 ±20% 0.123 2.23 1.81 100
NS 12565T 151MN RoHS 150 ±20% 0.173 1.84 1.54 100
NS 12565T 221MN RoHS 220 ±20% 0.273 1.39 1.18 100
NS 12575 type
Saturation current
Idc1
Temperature rise current
Idc2
NS 12575T 1R2NN RoHS 1.2 ±30% 0.0058 18.08 9.15 100
NS 12575T 2R7NN RoHS 2.7 ±30% 0.0085 13.91 7.69 100
NS 12575T 3R9NN RoHS 3.9 ±30% 0.0099 12.52 7.38 100
NS 12575T 5R6NN RoHS 5.6 ±30% 0.0116 10.85 6.36 100
NS 12575T 6R8NN RoHS 6.8 ±30% 0.0131 10.02 5.84 100
NS 12575T 100MN RoHS 10 ±20% 0.0156 7.65 5.55 100
NS 12575T 150MN RoHS 15 ±20% 0.0184 6.54 5.22 100
NS 12575T 220MN RoHS 22 ±20% 0.0260 5.56 4.05 100
NS 12575T 330MN RoHS 33 ±20% 0.0390 4.45 3.48 100
NS 12575T 470MN RoHS 47 ±20% 0.0515 3.76 2.95 100
NS 12575T 680MN RoHS 68 ±20% 0.0720 2.78 2.49 100
NS 12575T 101MN RoHS 100 ±20% 0.110 2.64 2.01 100
NS 12575T 151MN RoHS 150 ±20% 0.161 2.09 1.51 100
NS 12575T 221MN RoHS 220 ±20% 0.245 1.81 1.35 100
※) The saturation current value (Idc1) is the DC current value having inductance decrease down to 30%. (at 20℃)
※) The temperature rise current value (Idc2) is the DC current value having temperature increase up to 40℃. (at 20℃)
※) The rated current is the DC current value that satisfies both of current value saturation current value and temperature rise current value.
DC Resistance
[Ω](±20%)
Rated current ※) [A] Measuring frequency
[kHz]
Parts number EHS Nominal inductance
[μH] Inductance tolerance
Rated current ※) [A] Measuring frequency
[kHz]
Parts number EHS Nominal inductance
[μH] Inductance tolerance DC Resistance
[Ω](±20%)
i_smd_NS_e-E08R01.xls
POWER INDUCTORS
INDUCTORS
oocoooooonoooooo o7o7o7e7e7f77e77 79707 7 7e777777 TAIYD YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_smd_NS_pack_e-E05R01
SMD POWER INDUCTORS (NS SERIES)
PACKAGING
①Packing Quantity
Type Standard Quantity (1reel) [pcs] Minimum Quantity [pcs]
Embossed Tape Embossed Tape
NS10145 500 2000
NS10155 500 2000
NS10165 500 2000
NS12555 500 2000
NS12565 500 2000
NS12575 500 2000
②Tape Material
Embossed Tape
Top tape
Base tape
Sprocket hole
Chip cavity
Chip
Chip Filled
③Taping dimensions
Embossed tape 24mm wide (0.945 inches wide)
F2.0±0.1
(
0.079
±
0.004)
4.0±0.1
(
0.157
±
0.004)
1.75
±
0.1
(0.069±0.004)
11.5±0.1
(0.453±0.004)
24.0±0.3
(0.945±0.012)
φ1.5
0.1/
0
(φ0.059+0.004/-0)
Sprocket hole
A
B
T
K
Type Chip cavity Insertion pitch Tape thickness
A B F T K
NS10145 10.5±0.1
(0.413±0.004)
10.5±0.1
(0.413±0.004)
16.0±0.1
(0.630±0.004)
0.4±0.1
(0.016±0.004)
5.0±0.1
(0.197±0.004)
NS10155 10.5±0.1
(0.413±0.004)
10.5±0.1
(0.413±0.004)
16.0±0.1
(0.630±0.004)
0.4±0.1
(0.016±0.004)
6.0±0.1
(0.236±0.004)
NS10165 10.5±0.1
(0.413±0.004)
10.5±0.1
(0.413±0.004)
16.0±0.1
(0.630±0.004)
0.4±0.1
(0.016±0.004)
7.0±0.1
(0.276±0.004)
NS12555 13.0±0.1
(0.512±0.004)
13.0±0.1
(0.512±0.004)
16.0±0.1
(0.630±0.004)
0.4±0.1
(0.016±0.004)
6.1±0.1
(0.240±0.004)
NS12565 13.0±0.1
(0.512±0.004)
13.0±0.1
(0.512±0.004)
16.0±0.1
(0.630±0.004)
0.4±0.1
(0.016±0.004)
7.1±0.1
(0.280±0.004)
NS12575 13.0±0.1
(0.512±0.004)
13.0±0.1
(0.512±0.004)
16.0±0.1
(0.630±0.004)
0.4±0.1
(0.016±0.004)
8.0±0.1
(0.315±0.004)
Unit:mm(inch)
Blank portions Cavity Blank ponions Leader 0 C O O O C O O O O 3 j 3...] E 3......3 3 3 . . . | (9.42:;Dilrtnhelgfll‘ninl‘ (9~‘24490i':3‘:5“'"*'5 _. 560mm max Direction of tape feed (24.4 inches max) 24 5+2/—0 (0955+fl (mm—u; 20:05 (auntoazm n . a s moxoz ‘ ~ ( USIZiODflE aw a Pull direcuon 165 180 —. Tootape K \L Basetane TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_smd_NS_pack_e-E05R01
④Leader and Blank portion
⑤Reel size
Type Reel size (Reference values)
φD φd
NS10145
330±2
(12.99±0.079)
100±1
(3.937±0.039)
NS10155
NS10165
NS12555
NS12565
NS12575
Unit:mm(inch)
⑥Top Tape Strength
The top tape requires a peel-off force of 0.1 to 1.3N in the direction of the arrow as illustrated below.
TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_smd_NR_NS_reli_e-E04R01
SMD POWER INDUCTORS(NR□, NS SERIES)
RELIABILITY DATA
1. Operating Temperature Range
Specified Value
NR30/40/50/60/80, NRS20, NRV20/30,
NRH24/30 Type -25~+120℃
NRS40/50/60/80 Type -25~+125℃
NR10050 Type -25~+105℃
NS101, NS125 Type -40~+125℃
Test Methods and
Remarks Including self-generated heat
2. Storage Temperature Range
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type
-40~+85℃
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type:
-5 to 40℃ for the product with taping.
3. Rated current
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type
Within the specified tolerance
NR10050 Type
NS101, NS125 Type
4. Inductance
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type
Within the specified tolerance
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks
Measuring equipment : LCR Meter (HP 4285A or equivalent)
Measuring frequency : Specified frequency
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type :
Measuring equipment : LCR Meter (HP 4285A or equivalent)
Measuring frequency : 100kHz, 1V
NR10050 Type :
Measuring equipment : LCR Meter (HP 4263A or equivalent)
Measuring frequency : 100kHz, 1V
5. DC Resistance
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type
Within the specified tolerance
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks Measuring equipment : DC ohmmeter (HIOKI 3227 or equivalent)
6. Self resonance frequency
Specified Value
NR30/40/50/60/80, NRV30, NRH24/30,
NRS40/50/60/80 Type Within the specified tolerance
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks
NR30/40/50/60/80, NRV30, NRH24/30, NRS40/50/60/80 Type, NR10050 Type :
Measuring equipment : Impedance analyzer/material analyzer(HP4291A or equivalent HP4191A, 4192A or equivalent)
VWH\ Force Rod 20 R5 10/ 7, RZBDJ ‘ Beam ‘ ‘ ‘ Teslsamma ‘ L5+2mm 4542mm H TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_smd_NR_NS_reli_e-E04R01
7. Temperature characteristic
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type Inductance change : Within ±20%
NR10050 Type
NS101, NS125 Type Inductance change : Within ±15%
Test Methods and
Remarks
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type :
Measurement of inductance shall be taken at temperature range within -25℃~+85℃.
With reference to inductance value at +20℃., change rate shall be calculated.
NS101, NS125 Type :
Measurement of inductance shall be taken at temperature range within -40℃~+125℃.
With reference to inductance value at +20℃., change rate shall be calculated.
Change of maximum inductance deviation in step 1 to 5
Step Temperature(℃)
1 20
2 Minimum operating temperature
3 20 (Standard temperature)
4 Maximum operating temperature
5 20
8. Resistance to flexure of substrate
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type No damage
NR10050 Type
NS101, NS125 Type No damage
Test Methods and
Remarks
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NS101/125 Type :
The test samples shall be soldered to the test board by the reflow. As illustrated below, apply force in the direction of the arrow indicating
until deflection of the test board reaches to 2 mm.
Test board size : 100×40×1.0
Test board material : Glass epoxy-resin
Solder cream thickness : 0.10mm (NR30, NRS20, NRH24/30, NRV20/30)
: 0.15mm(NR40/50/60/80, NRS40/50/60, NS101/125Type)
Land dimension
A
A B
C
Type A B C
NRS20, NRV20 0.65 0.7 2.0
NRH24 0.7 0.75 2.0
NR30, NRV30, NRH30 0.8 1.4 2.7
NR40, NRS40 1.2 1.6 3.7
NR50, NRS50 1.5 2.1 4.0
NR60, NRS60 1.6 3.1 5.7
NR80, NRS80 1.8 3.8 7.5
Type A B C
NS101 2.5 5.6 3.2
NS125 2.5 8.6 3.2
9. Insulation resistance : between wires
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type
NR10050 Type
NS101, NS125 Type
10. Insulation resistance : between wire and core
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type
NR10050 Type
NS101, NS125 Type
TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_smd_NR_NS_reli_e-E04R01
11. Withstanding voltage : between wire and core
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type
NR10050 Type
NS101, NS125 Type
12. Adhesion of terminal electrode
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type
Shall not come off PC board
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NS101/125 Type :
The test samples shall be soldered to the test board by the reflow.
Applied force : 10N to X and Y directions.
Duration : 5s.
Solder cream thickness : 0.10mm (NR30, NRS20, NRH24/30, NRV20/30)
: 0.15mm (NR40/50/60/80, NRS40/50/60, NS101/125Type)
NR10050 Type
Applied force : 5N to X and Y directions.
Duration : 5s.
13. Resistance to vibration
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type Inductance change : Within ±10%
No significant abnormality in appearance.
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type :
The test samples shall be soldered to the test board by the reflow.
Then it shall be submitted to below test conditions.
Frequency Range 10~55Hz
Total Amplitude 1.5mm (May not exceed acceleration 196m/s2)
Sweeping Method 10Hz to 55Hz to 10Hz for 1min.
Time
X
For 2 hours on each X, Y, and Z axis. Y
Z
Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs.
14. Solderability
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type
At least 90% of surface of terminal electrode is covered by new solder.
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks
The test samples shall be dipped in flux, and then immersed in molten solder as shown in below table.
Flux : Methanol solution containing rosin 25%.
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type
Solder Temperature 245±5℃
Time 5±1.0 sec.
※Immersion depth : All sides of mounting terminal shall be immersed.
TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_smd_NR_NS_reli_e-E04R01
15. Resistance to soldering heat
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type Inductance change : Within ±10%
No significant abnormality in appearance.
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type :
The test sample shall be exposed to reflow oven at 230±5 for 40 seconds, with peak temperature at 260±5℃ for 5 seconds, 2 times.
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80Type, NS101/125 Type
Test board material : Glass epoxy-resin
Test board thickness : 1.0mm
NR10050 Type
Test board material : Glass epoxy-resin
Test board thickness : 1.6mm
Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs.
16. Thermal shock
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type Inductance change : Within ±10%
No significant abnormality in appearance.
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type :
The test samples shall be soldered to the test board by the reflow. The test samples shall be placed at specified temperature for specified
time by step 1 to step 4 as shown in below table in sequence. The temperature cycle shall be repeated 100 cycles.
Conditions of 1 cycle
Step Temperature (℃) Duration (min)
1 -40±3 30±3
2 Room temperature Within 3
3 +85±2 30±3
4 Room temperature Within 3
Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs.
17. Damp heat
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type
Inductance change : Within ±10%
No significant abnormality in appearance.
NR10050 Type
NS101, NS125 Type Inductance change : Within ±10%
No significant abnormality in appearance.
Test Methods and
Remarks
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NS101/125 Type :
The test samples shall be soldered to the test board by the reflow.
The test samples shall be placed in thermostatic oven set at specified temperature and humidity as shown in below table.
Temperature 60±2℃
Humidity 90~95%RH
Time 500+24/-0 hour
Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs.
18. Loading under damp heat
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type Inductance change : Within ±10%
No significant abnormality in appearance.
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type :
The test samples shall be soldered to the test board by the reflow.
The test samples shall be placed in thermostatic oven set at specified temperature and humidity and applied the rated current
continuously as shown in below table.
Temperature 60±2℃
Humidity 90~95%RH
Applied current Rated current
Time 500+24/-0 hour
Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs.
TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_smd_NR_NS_reli_e-E04R01
19. Low temperature life test
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type Inductance change : Within ±10%
No significant abnormality in appearance.
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type :
The test samples shall be soldered to the test board by the reflow. After that, the test samples shall be placed at test conditions as shown
in below table.
Temperature -40±2℃
Time 500+24/-0 hour
Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs.
20. High temperature life test
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks
NR10050 Type :
Temperature 105±3℃
Time 500+24/-0 hour
Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs.
21. Loading at high temperature life test
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type
Inductance change : Within ±10%
No significant abnormality in appearance.
NR10050 Type
NS101, NS125 Type Inductance change : Within ±10%
No significant abnormality in appearance.
Test Methods and
Remarks
NR30/40/50/60/80, NRV30, NRH24/30, NRS40/50/60/80 Type, NS12555, NS12565, NS12575 Type :
The test samples shall be soldered to the test board by the reflow soldering.
Temperature 85±2℃
Applied current Rated current
Time 500+24/-0 hour
Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs.
22. Standard condition
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type
Standard test condition :
Unless otherwise specified, temperature is 20±15 and 65±20%of
relative humidity.
When there is any question concerning measurement result: In order to
provide correlation data, the test shall be condition of 20±2 of
temperature, 65±5% relative humidity.
Inductance is in accordance with our measured value.
NR10050 Type
NS101, NS125 Type
TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/)
i_smd_NR_NS_prec_e-E06R01
SMD POWER INDUCTORS(NR□, NS SERIES)
PRECAUTIONS
1. Circuit Design
Precautions
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment,
telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical
equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear
control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or
damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2. PCB Design
Precautions
◆Land pattern design
1. Please refer to a recommended land pattern.
2. There is stress, which has been caused by distortion of a PCB, to the inductor.
(NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type)
3. Please consider the arrangement of parts on a PCB. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type)
Technical
considerations
◆Land pattern design
Surface Mounting
1. Mounting and soldering conditions should be checked beforehand.
2. Applicable soldering process to this products is reflow soldering only.
3. Please use the recommended land pattern shown as below. Electrical characteristics and the mounting ability of the product are being
considered in the recommended land pattern. If a PCB is designed with other dimensions, defective soldering and stress to a product
may occur due to misalignment. The performance of the product may not be brought out. If an adopted land pattern is different from the
recommended land pattern, stress to the product will increase. It may cause cracks or defective electrical characteristics of the
product. Please conduct validation completely before studying adoption of this product and please judge the pros and cons of adoption
of this product with taking on responsibility.
(NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type)
4. As coefficients of thermal expansion between an inductor and a PCB differs, cracks may occur on a ferrite core when thermal stress is
applied to them after mounting an inductor. (Please refer to the drawings below.) Please conduct validation completely before studying
adoption of this product and please judge the pros and cons of adoption of this product with taking on responsibility.
(NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type)
5. SMD inductors should be located to minimize any possible mechanical stresses from board warp or deflection. When splitting the PC
board after mounting inductors and other components, care is required so as not to give any stresses of deflection or twisting to the
board.
(NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type)
A
B
C
D
Electrode
Perforation
Slit
A product tends to undergo stress in order “A>C>B≡D”.
Please consider the layouts of a product to minimize any stresses.
Clack on ferrite core
Solder, electrode
PCB
300 Ssec max 8 ,4 ' < peak:="" g="" 200="" m‘="" 250+5/—o”c="" a="" 2="" e="" 10“="" ,9="" heating="" nmelsec]="" taiyd="" yuden="">
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/)
i_smd_NR_NS_prec_e-E06R01
3. Considerations for automatic placement
Precautions
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
Technical
considerations
◆Adjustment of mounting machine
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
2. Stress may be applied to a product with a warp or a twist in handling of the product. Please conduct validation completely before
studying adoption of this product and please judge the pros and cons of adoption of this product with taking on responsibility.
(NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type)
Wrap Twist
4. Soldering
Precautions
◆Reflow soldering
1. Please contact any of our offices for a reflow soldering, and refer to the recommended condition specified.
2. The product shall be used reflow soldering only.
3. Please do not add any stress to a product until it returns in normal temperature after reflow soldering.
◆Lead free soldering
1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering
heat, soldering etc sufficiently.
◆Recommended conditions for using a soldering iron (NR10050 Type)
Put the soldering iron on the land-pattern.
Soldering iron's temperature - Below 350℃
Duration - 3 seconds or less
The soldering iron should not directly touch the inductor.
Technical
considerations
◆Reflow soldering
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently
degrade the reliability of the products.
・NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type
Recommended reflow condition (Pb free solder)
5. Cleaning
Precautions ◆Cleaning conditions
1. Washing by supersonic waves shall be avoided.
Technical
considerations
◆Cleaning conditions
1. If washed by supersonic waves, the products might be broken.
TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/)
i_smd_NR_NS_prec_e-E06R01
6. Handling
Precautions
◆Handling
1. Keep the product away from all magnets and magnetic objects.
◆Breakaway PC boards (splitting along perforations)
1. When splitting the PC board after mounting product, care should be taken not to give any stresses of deflection or twisting to the board.
2. Board separation should not be done manually, but by using the appropriate devices.
◆Mechanical considerations
1. Please do not give the product any excessive mechanical shocks.
2. Please do not add any shock and power to a product in transportation.
◆Pick-up pressure
1. Please do not push to add any pressure to a winding part. Please do not give any shock and push into a ferrite core exposure part.
◆Packing
1. Please avoid accumulation of a packing box as much as possible.
Technical
considerations
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Breakaway PC boards (splitting along perforations)
1. The position of the product on PCBs shall be carefully considered to minimize the stress caused from splitting of the PCBs.
◆Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
2. There is a case to be broken by the handling in transportation.
◆Pick-up pressure
1. Damage and a characteristic can vary with an excessive shock or stress.
◆Packing
1. If packing boxes are accumulated, that could cause a deformation on packing tapes or a damage on the products.
7. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the
storage area should be controlled.
Recommended conditions
Ambient temperature : -5~40℃
Humidity : Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may
decrease as time passes.
For this reason, product should be used within 6 months from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical
considerations
◆Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes
and deterioration of taping/packaging materials may take place.

Products related to this Datasheet

FIXED IND 150UH 1.51A 193.2 MOHM
Available Quantity: 22,500
Unit Price: 1.14728
FIXED IND 47UH 2.95A 61.8MOHM SM
Available Quantity: 22,000
Unit Price: 1.14728
FIXED IND 100UH 2.01A 132MOHM SM
Available Quantity: 19,500
Unit Price: 1.14728
FIXED IND 68UH 2.3A 93 MOHM SMD
Available Quantity: 9,500
Unit Price: 1.08172
FIXED IND 220UH 1.35A 245MOHM SM
Available Quantity: 5,500
Unit Price: 1.14728
FIXED IND 6.8UH 5.84A 15.72 MOHM
Available Quantity: 2,000
Unit Price: 1.04298
FIXED IND 15UH 5.22A 22.08 MOHM
Available Quantity: 2,000
Unit Price: 1.14728
FIXED IND 7UH 5.21A 19.44MOHM SM
Available Quantity: 1,500
Unit Price: 0.98338
FIXED IND 150UH 1.54A 207.6 MOHM
Available Quantity: 1,500
Unit Price: 1.08172
FIXED IND 33UH 3.22A 46.8MOHM SM
Available Quantity: 1,000
Unit Price: 1.08172
FIXED IND 47UH 2.78A 69 MOHM SMD
Available Quantity: 1,000
Unit Price: 1.08172
FIXED IND 33UH 3.48A 46.8MOHM SM
Available Quantity: 1,000
Unit Price: 1.14728
FIXED IND 68UH 2.49A 86.4MOHM SM
Available Quantity: 1,000
Unit Price: 1.14728
FIXED IND 15UH 4.33A 28.44 MOHM
Available Quantity: 500
Unit Price: 0.98338
FIXED IND 1.2UH 9.15A 6.96 MOHM
Available Quantity: 500
Unit Price: 1.04298
FIXED IND 4.2UH 5.91A 15.12 MOHM
Available Quantity: 0
Unit Price: 0.98338
FIXED IND 10UH 4.75A 23.88 MOHM
Available Quantity: 0
Unit Price: 0.96154
FIXED IND 22UH 3.91A 37.2MOHM SM
Available Quantity: 0
Unit Price: 0.98338
FIXED IND 100UH 1.81A 147.6 MOHM
Available Quantity: 0
Unit Price: 0.96154
FIXED IND 220UH 1.18A 327.6 MOHM
Available Quantity: 0
Unit Price: 0.96154
FIXED IND 2.7UH 7.69A 10.2 MOHM
Available Quantity: 0
Unit Price: 1.14728
FIXED IND 3.9UH 7.38A 11.88 MOHM
Available Quantity: 0
Unit Price: 1.04298
FIXED IND 5.6UH 6.36A 13.92 MOHM
Available Quantity: 0
Unit Price: 1.04298
FIXED IND 10UH 5.55A 18.72 MOHM
Available Quantity: 0
Unit Price: 1.14728
FIXED IND 22UH 4.05A 31.2MOHM SM
Available Quantity: 0
Unit Price: 1.14728
FIXED IND 1MH 680MA 1.112OHM SMD
Available Quantity: 0
Unit Price: 0
FIXED IND 220UH 1.35A 245MOHM SM
Available Quantity: 5,962
Unit Price: 2.23
FIXED IND 1MH 680MA 1.112OHM SMD
Available Quantity: 0
Unit Price: 0
FIXED IND 5.6UH 4.45A 21MOHM SMD
Available Quantity: 0
Unit Price: 0.60369
FIXED IND 6.8UH 5.22A 16.8 MOHM
Available Quantity: 0
Unit Price: 0.71022