TPS3800-xx, 3801-xx,3802-xx Datasheet by Texas Instruments

I TEXAS % INSTRUMENTS I: j i I: i I: j foi I: j I: i I: :

TPS380x . . . DCKPACKAGE

(TOPVIEW)

RESET

GND

VDD

GND

TPS3801−01. . . DCKPACKAGE

(TOPVIEW)

RESET

GND

SENSE

VDD

GND

VDD =1.8V

100nF

TPS3801E18

TMS320VC5420

GND

MR RESET RESET

CoreVDD

VDD

TPS3800-xx

TPS3801-xx

TPS3802-xx

www.ti.com

SLVS219E –AUGUST 1999–REVISED OCTOBER 2010

ULTRA-SMALL SUPPLY VOLTAGE SUPERVISORS

Check for Samples: TPS3800-xx,TPS3801-xx,TPS3802-xx

1FEATURES DESCRIPTION

2• Small, 5-Pin SC-70 (SOT-323) Package

• Supply Current of 9 mAThe TPS380x family of supervisory circuits monitor

supply voltages to provide circuit initialization and

• Power-On Reset Generator With Fixed Delay timing supervision, primarily for DSPs and other

Time processor-based systems.

– TPS3800 = 100 ms These devices assert a push-pull RESET signal when

– TPS3801 = 200 ms the SENSE (adjustable version) or VDD (fixed version)

– TPS3802 = 400 ms drops below a preset threshold. The RESET output

remains asserted for the factory programmed delay

• Precision Supply Voltage Monitor 1.8 V, 2.5 V, time after the SENSE or VDD return above its

2.7 V, 3 V, 3.3 V, 5 V, and Adjustable threshold.

• Manual Reset Input (Except TPS3801-01) The TPS380x devices, except the TPS3801-01,

• Temperature Range: –40°C to +85°C incorporate a manual reset input (MR). A low level at

MR causes RESET to become active.

APPLICATIONS The TPS380x uses a precision reference to achieve

• Applications Using DSPs, Microcontrollers, or an overall threshold accuracy of 2%—2.5%. These

Microprocessors devices are available in a 5-pin SC-70 package,

• Wireless Communication Systems which is only about half the size of a 5-pin SOT-23

• Portable/Battery-Powered Equipment package.

• Programmable Controls The TPS380x devices are fully specified over a

• Intelligent Instruments temperature range of –40°C to +85°C.

• Industrial Equipment

• Notebook/Desktop Computers

• Automotive Systems

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2All trademarks are the property of their respective owners.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

l TEXAS INSTRUMENTS

TPS3800-xx

TPS3801-xx

TPS3802-xx

SLVS219E –AUGUST 1999–REVISED OCTOBER 2010

www.ti.com

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

AVAILABLE OPTIONS(1)

TADEVICE NAME THRESHOLD VOLTAGE TYP DELAY TIME MARKING

TPS3801-01DCK Adjustable (Vref = 1.14 V) 200 ms ARF

TPS3801E18DCK 1.71 V 200 ms ARE

TPS3801J25DCK 2.25 V 200 ms NJA

TPS3800G27DCK 2.5 V 95 ms ARI

TPS3801L30DCK 2.64 V 200 ms NPA

–40°C to 85°C TPS3801K33DCK 2.93 V 200 ms NWA

TPS3802L30DCK 2.64 V 380 ms ASA

TPS3802K33DCK 2.93 V 380 ms ARK

TPS3801T50DCK 4.00 V 25 ms AVI

TPS3801I50DCK 4.55 V 200 ms NSA

(1) For the most current package and ordering information, see the Package Option Addendum at the end of this data sheet, or refer to our

web site at www.ti.com.

ABSOLUTE MAXIMUM RATINGS(1) (2)

Over operating free-air temperature range (unless otherwise noted).

UNIT

Supply voltage, VDD 7 V

SENSE –0.3 V to 5 V

All other pins –0.3 V to 7 V

MR –0.3 V to VDD + 0.3 V

RESET –0.3 V to VDD + 0.3 V

Maximum low-output current, IOL 5 mA

Maximum high-output current, IOH –5 mA

Input-clamp current, IIK (VI< 0 or VI> VDD) ±20 mA

Output-clamp current, IOK (VO< 0 or VO> VDD) ±20 mA

Operating junction temperature range, TJ(3) –40°C to +85°C

Storage temperature range, Tstg –65°C to +150°C

(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings

only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating

conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

(2) All voltage values are with respect to GND. For reliable operation, the device should not be operated at 7 V for more than t = 1000h

continuously.

(3) Due to the low dissipation power of this device, it is assumed that TJ= TA.

RECOMMENDED OPERATING CONDITIONS

MIN MAX UNIT

TPS3801J25, TPS3801L30, TPS3801K33, TPS3801I50, TPS3801T50 2 6

Supply voltage, VDD V

All other devices 1.6 4

SENSE 0 See (1) V

Input voltage, VI0 VDD +0.3 V

High-level input voltage, VIH 0.7 × VDD VDD +0.3 V

Low-level input voltage, VIL 0.3 × VDD V

Input transition rise and fall rate at MR, Δt/ΔV 100 ns/V

VPull-up

Pull-up resistor value, RESET Ω

50µA

Operating free-air temperature range, TA–40 +85 °C

(1) Maximum = VDD + 0.3 or 4.5 V, whichever is greater.

Product Folder Link(s): TPS3800-xx TPS3801-xx TPS3802-xx

l TEXAS INSTRUMENTS

TPS3800-xx

TPS3801-xx

TPS3802-xx

www.ti.com

SLVS219E –AUGUST 1999–REVISED OCTOBER 2010

ELECTRICAL CHARACTERISTICS

Over –40°C to +85°C free-air temperature range (unless otherwise noted).

TPS3800-xx, TPS3801-xx,

TPS3802-xx

PARAMETER TEST CONDITIONS

MIN TYP MAX UNIT

VDD = 1.6 V to 6 V IOH = –500 mA VDD –0.2

VOH High-level output voltage (RESET) VDD = 3.3 V IOH = –2 mA VDD –0.4 V

VDD = 6 V IOH = –4 mA (1) VDD –0.4

VDD = 1.6 V to 6 V, IOL = 500 mA 0.2

VOL Low-level output voltage (RESET) VDD = 3.3 V, IOL = 2 mA 0.4 V

VDD = 6 V, IOL = 4 mA (1) 0.4

Power-up reset voltage(2) VDD ≥1.1 V, IOL = 50 mA 0.2 V

TPS380x-01 1.117 1.14 1.163

TPS380xE18 1.67 1.71 1.75

TPS380xJ25 2.2 2.25 2.3

TPS380xG27 2.45 2.5 2.55

Negative-going input

VIT– TA= –40°C to 85°C V

threshold voltage(3) TPS380xL30 2.58 2.64 2.7

TPS380xK33 2.87 2.93 2.99

TPS380xI50 4.45 4.55 4.65

TPS380xT50 3.92 4 4.08

TPS380x-01 15

TPS380xx18 25

TPS380xx25 30

Vhys Threshold hysteresis TPS380xx27 35 mV

TPS380xx30 35

TPS380xx33 40

TPS380xx50 60

IIH High-level input current (MR) MR = 0.7×VDD, VDD = 6 V –40 –60 –100 mA

IIL Low-level input current (MR) MR = 0 V, VDD = 6 V –130 –200 –340

IIInput current (SENSE) –25 25 nA

TPS3801J25, VDD = 2 V, MR and output 9 12

TPS3801L30, unconnected

TPS3801K33, VDD = 6 V, MR and output

TPS3801I50, 20 25

unconnected

TPS3801T50

VDD = 1.6 V, SENSE = 0 V to VDD,7 10

output unconnected

IDD Supply current mA

TPS3801-01 VDD = 4 V, SENSE = 0 V to VDD,9 12

output unconnected

VDD = 1.6 V, MR and output

TPS3801E18, 8 11

unconnected

TPS3800G27,

TPS3802K33, VDD = 4 V, MR and output 13 18

TPS3802L30 unconnected

CiInput capacitance VI= 0 V to VDD 5 pF

(1) Only valid for the TPS3801J25, TPS3801L30, TPS3801K33, TPS3801I50, and TPS3801T50.

(2) The lowest supply voltage at which RESET becomes active. tr, VDD ≥15 ms/V.

(3) To ensure the best stability of the threshold voltage, a bypass capacitor (0.1-mF ceramic) should be placed near the supply terminals.

Product Folder Link(s): TPS3800-xx TPS3801-xx TPS3802-xx

‘5‘ TEXAS INSTRUMENTS

VDD

V(NOM)

VIT

1.1 V

Undefined Behavior of

RESET Output For VDD < 1.1 V

RESET

tdtd

TPS3800-xx

TPS3801-xx

TPS3802-xx

SLVS219E –AUGUST 1999–REVISED OCTOBER 2010

www.ti.com

TIMING REQUIREMENTS

at RL= 1 MΩ, CL= 50 pF, TA= +25°C

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

at SENSE VDD = 1.6 V, VIH = 1.1 × VIT–, VIL = 0.9 × VIT– 1ms

twPulse width at VDD VDD = VIT– + 0.2 V, VDD = VIT– –0.2 V 3

at MR VDD ≥VIT– + 0.2 V, VIL = 0.3 × VDD, VIH = 0.7 × VDD 100 ns

SWITCHING CHARACTERISTICS

at RL= 1 MΩ, CL= 50 pF, TA= +25°C

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

TPS3801T50 15 25 35

VDD ≥VIT– + 0.2 V,

TPS3800 60 95 140

tdRESET recovery delay time MR ≥0.7 × VDD ms

TPS3801 120 200 280

See timing diagram

TPS3802 240 380 560

VDD ≥VIT– + 0.2 V,

MR to RESET delay VIL = 0.3 × VDD, 15 ns

Propagation (delay) time, high-to-low-level VIH = 0.7 × VDD

tPHL output VDD to RESET delay VIL = VIT– – 0.2 V, 1ms

VIH = VIT– + 0.2 V

SENSE to RESET

TIMING DIAGRAM

NOTE: RESET should not be forced high during the power-up sequence (until VDD > 1.1 V).

Product Folder Link(s): TPS3800-xx TPS3801-xx TPS3802-xx

*9 TEXAS INSTRUMENTS R2 Resel Logic . Tlmev TPSSBm >01 Device Supply Voltage SENSE

FUNCTION/TRUTH TABLE, TPS380x

RESET

VDD>VIT

VDD

30 kΩ

VDD

GND

RESET

TPS380x

Oscillator

Reference

Voltage

of 1.14 V

Reset

Logic

Timer

SENSE

RESET

TPS3801−01

Oscillator

Reference

Voltage

of 1.14 V

Reset

Logic

Timer

VDD Device Supply

Voltage VDD

TPS3800-xx

TPS3801-xx

TPS3802-xx

www.ti.com

SLVS219E –AUGUST 1999–REVISED OCTOBER 2010

FUNCTIONAL BLOCK DIAGRAMS

Figure 1.

Figure 2.

Product Folder Link(s): TPS3800-xx TPS3801-xx TPS3802-xx

l TEXAS INSTRUMENTS

−50

−40

−30

−20

−10

−2 0 2 4 6

MR = OPEN

TA = 25°C

VDD − Supply Voltage − V

ISupply Current − − Aµ

TPS3801J25

0.00

0.25

0.50

0.75

1.00

1.25

1.50

1.75

2.00

2.25

2.50

2.75

0.0 2.5 5.0 7.5 10.0 12.5

VDD = 2.5 V

MR = OPEN

TA = 85°C

TA = -40°C

IOL − Low-Level Output Current − mA

V− Low-Level Output Voltage − V

TA = 25°C

TA = 0°C

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

5.0

5.5

6.0

6.5

IOH − High-Level Output Current − mA

VDD = 6.0 V

MR = OPEN

TA = 85°C

0 −10 −20 −30 −40 −50

VOH − High-Level Output Voltage − V

TA = -40°C

TA = 0°C

TA = 25°C

0.00

0.25

0.50

0.75

1.00

1.25

1.50

1.75

2.00

2.25

2.50

2.75

3.00

IOH − High-Level Output Current − mA

VDD = 2.5 V

MR = OPEN

TA = 85°C

0 −2 −4 −6 −8 −10

VOH − High-Level Output Voltage − V

TA = -40°C

TA = 25°C

TA = 0°C

TPS3800-xx

TPS3801-xx

TPS3802-xx

SLVS219E –AUGUST 1999–REVISED OCTOBER 2010

www.ti.com

TYPICAL CHARACTERISTICS

spacer

LOW-LEVEL OUTPUT VOLTAGE SUPPLY CURRENT

vs vs

LOW-LEVEL OUTPUT CURRENT SUPPLY VOLTAGE

Figure 3. Figure 4.

HIGH-LEVEL OUTPUT VOLTAGE HIGH-LEVEL OUTPUT VOLTAGE

vs vs

HIGH-LEVEL OUTPUT CURRENT HIGH-LEVEL OUTPUT CURRENT

Figure 5. Figure 6.

Product Folder Link(s): TPS3800-xx TPS3801-xx TPS3802-xx

l TEXAS INSTRUMENTS | 7 : 1 \ 1 \ . S \ o 5 5 A . v. 7 6 / ,, TA - Free-Air Temperature al VDD TA - Free-Air Temperature at vDD

MR = OPEN

1.5

0.5

00 0.2 0.4 0.6

3.5

0.8 1

2.5

VDD Threshold Overdrive Voltage − V

− Minimum Pulse Duration at µs

VDD−tw

−500

−400

−300

−200

−100

100

−2 0 2 4 6

VDD = 6 V

TA = 25°C

VI − Input Voltage at MR − V

− Input Current − A

IIµ

0.988

0.990

0.992

0.994

0.996

0.998

1.002

1.004

1.006

−40 −20 0 20 40 60 80

TPS3801−01

TPS3801E18

TPS3800

TPS3802

− Normalized Input Threshold Voltage − VVIT

TA − Free-Air Temperature at VDD − °C

0.995

0.996

0.997

0.998

0.999

1.000

1.001

TA − Free-Air Temperature at VDD − °C

−40 −20 0 20 40

Normalized Input Threshold Voltage

60 85

MR = OPEN

VIT (TA)/VIT (25 )

TPS3801S25

TPS3801L30

TPS3801K33

TPS3801I50

TPS3801T50

TPS3800-xx

TPS3801-xx

TPS3802-xx

www.ti.com

SLVS219E –AUGUST 1999–REVISED OCTOBER 2010

TYPICAL CHARACTERISTICS (continued)

spacer spacer

INPUT CURRENT MINIMUM PULSE DURATION AT VDD

vs vs

INPUT VOLTAGE AT MR VDD THRESHOLD OVERDRIVE VOLTAGE

Figure 7. Figure 8.

NORMALIZED INPUT THRESHOLD VOLTAGE NORMALIZED INPUT THRESHOLD VOLTAGE

vs vs

FREE-AIR TEMPERATURE AT VDD FREE-AIR TEMPERATURE AT VDD

Figure 9. Figure 10.

Product Folder Link(s): TPS3800-xx TPS3801-xx TPS3802-xx

l TEXAS INSTRUMENTS

TPS3800-xx

TPS3801-xx

TPS3802-xx

SLVS219E –AUGUST 1999–REVISED OCTOBER 2010

www.ti.com

Changes from Revision D (December 2006) to Revision E Page

• Added Pull-up resistor value, RESET to the Recommended Operating Conditions Table .................................................. 2

Product Folder Link(s): TPS3800-xx TPS3801-xx TPS3802-xx

I TEXAS INSTRUMENTS Samples Samples Samples Samples Samples Samples Samples Samples Sample: Sample: Samples Samples Samples Samples Samples Samples Samples Samples

PACKAGE OPTION ADDENDUM

www.ti.com 10-Dec-2020

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead finish/

Ball material

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

HPA00763DCKR ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ARF

TPS3800G27DCKR ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ARI

TPS3800G27DCKRG4 ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ARI

TPS3801-01DCKR ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ARF

TPS3801-01DCKRG4 ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ARF

TPS3801E18DCKR ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ARE

TPS3801I50DCKR ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 NSA

TPS3801I50DCKRG4 ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 NSA

TPS3801J25DCKR ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 NJA

TPS3801K33DCKR ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 NWA

TPS3801K33DCKRG4 ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 NWA

TPS3801L30DCKR ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 NPA

TPS3801L30DCKRG4 ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 NPA

TPS3801T50DCKR ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AVI

TPS3801T50DCKRG4 ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AVI

TPS3802K33DCKR ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ARK

TPS3802L30DCKR ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ASA

TPS3802L30DCKRG4 ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ASA

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

I TEXAS INSTRUMENTS

PACKAGE OPTION ADDENDUM

www.ti.com 10-Dec-2020

Addendum-Page 2

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance

do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may

reference these types of products as "Pb-Free".

RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.

Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based

flame retardants must also meet the <=1000ppm threshold requirement.

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two

lines if the finish value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

I TEXAS INSTRUMENTS REEL DIMENSIONS TAPE DIMENSIONS Reel Dlameter Cavtty AD Dimension destgned to accommodate the component wmth Eu Dimension destgned to accommodate the componenl Iength K0 Dtmenston destgned to accommodate the component thickness 7 w Ovevau with at the earner tape i Pt PIlCh between successtve cavtty cemers f T ReelWidIh(W1) QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE C) O O O C) O O O ispmckeIHuIes —> User Dtrecllnn OI Feed \I/ Pockel Quadrams

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

TPS3800G27DCKR SC70 DCK 5 3000 180.0 8.4 2.41 2.41 1.2 4.0 8.0 Q3

TPS3800G27DCKR SC70 DCK 5 3000 178.0 9.0 2.4 2.5 1.2 4.0 8.0 Q3

TPS3801-01DCKR SC70 DCK 5 3000 178.0 9.0 2.4 2.5 1.2 4.0 8.0 Q3

TPS3801-01DCKR SC70 DCK 5 3000 180.0 8.4 2.41 2.41 1.2 4.0 8.0 Q3

TPS3801E18DCKR SC70 DCK 5 3000 178.0 9.0 2.4 2.5 1.2 4.0 8.0 Q3

TPS3801E18DCKR SC70 DCK 5 3000 180.0 8.4 2.41 2.41 1.2 4.0 8.0 Q3

TPS3801I50DCKR SC70 DCK 5 3000 180.0 8.4 2.41 2.41 1.2 4.0 8.0 Q3

TPS3801J25DCKR SC70 DCK 5 3000 180.0 8.4 2.41 2.41 1.2 4.0 8.0 Q3

TPS3801K33DCKR SC70 DCK 5 3000 178.0 9.0 2.4 2.5 1.2 4.0 8.0 Q3

TPS3801K33DCKR SC70 DCK 5 3000 180.0 8.4 2.41 2.41 1.2 4.0 8.0 Q3

TPS3801L30DCKR SC70 DCK 5 3000 180.0 8.4 2.41 2.41 1.2 4.0 8.0 Q3

TPS3801T50DCKR SC70 DCK 5 3000 178.0 9.0 2.4 2.5 1.2 4.0 8.0 Q3

TPS3801T50DCKR SC70 DCK 5 3000 180.0 8.4 2.41 2.41 1.2 4.0 8.0 Q3

TPS3802K33DCKR SC70 DCK 5 3000 178.0 9.0 2.4 2.5 1.2 4.0 8.0 Q3

TPS3802K33DCKR SC70 DCK 5 3000 180.0 8.4 2.41 2.41 1.2 4.0 8.0 Q3

TPS3802L30DCKR SC70 DCK 5 3000 178.0 9.0 2.4 2.5 1.2 4.0 8.0 Q3

TPS3802L30DCKR SC70 DCK 5 3000 180.0 8.4 2.41 2.41 1.2 4.0 8.0 Q3

PACKAGE MATERIALS INFORMATION

www.ti.com 24-Apr-2020

Pack Materials-Page 1

I TEXAS INSTRUMENTS TAPE AND REEL BOX DIMENSIONS

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

TPS3800G27DCKR SC70 DCK 5 3000 183.0 183.0 20.0

TPS3800G27DCKR SC70 DCK 5 3000 180.0 180.0 18.0

TPS3801-01DCKR SC70 DCK 5 3000 180.0 180.0 18.0

TPS3801-01DCKR SC70 DCK 5 3000 183.0 183.0 20.0

TPS3801E18DCKR SC70 DCK 5 3000 180.0 180.0 18.0

TPS3801E18DCKR SC70 DCK 5 3000 183.0 183.0 20.0

TPS3801I50DCKR SC70 DCK 5 3000 183.0 183.0 20.0

TPS3801J25DCKR SC70 DCK 5 3000 183.0 183.0 20.0

TPS3801K33DCKR SC70 DCK 5 3000 180.0 180.0 18.0

TPS3801K33DCKR SC70 DCK 5 3000 183.0 183.0 20.0

TPS3801L30DCKR SC70 DCK 5 3000 183.0 183.0 20.0

TPS3801T50DCKR SC70 DCK 5 3000 180.0 180.0 18.0

TPS3801T50DCKR SC70 DCK 5 3000 183.0 183.0 20.0

TPS3802K33DCKR SC70 DCK 5 3000 180.0 180.0 18.0

TPS3802K33DCKR SC70 DCK 5 3000 183.0 183.0 20.0

TPS3802L30DCKR SC70 DCK 5 3000 180.0 180.0 18.0

TPS3802L30DCKR SC70 DCK 5 3000 183.0 183.0 20.0

PACKAGE MATERIALS INFORMATION

www.ti.com 24-Apr-2020

Pack Materials-Page 2

MECHANICAL DATA DCK (R—PDSO—GS) PLASTIC SMALL—OUTLINE PACKAGE E was 5 47 Fl Fl f f 240 \ ,i, w 1,80 1,10 Pm/ \ ‘ $ ‘ . maexArea Wm H 1* MO Um Gauge Mane Seanng Mane ﬁt Scam Mane gig/Em 409555575/8 U‘ /200/ , m m hmeters NO'FS AH \mec' dwmensiur: Umm> FuHs an JFDFC M07763 vunuhcn AA Tm drawmq \s sumsc: 0 change wmu: nome Body mmensmns do nut mc‘ude mom ﬂcsh m aroms'm Mom Has» and pruvuswon W m exceed 015 :2r m INSrRUMEm-s www.1i.com

LAND PATTERN DATA DC< (="" 7pjsoic5=""> PLASTC SMALL OU’LME Exc'm‘e Boc'd LuyuM stem Openings Based or a stencﬂ tn'ckndss uf 127mm (005m) /23\\der Musk Cpen'v‘g d d s W \‘ ‘\“=bd Geometry \ v y \ NOTES- A M \meur dimensmns are m miHWete's a. In: druwv‘q is sweat (a chc'vge mud: 'vuhce c Custume's snodd p‘uce d note 01 me mm: buurd (abr'cahun c'awmg nm :0 mm the ce'ﬂe' smder musk denned Dad, n mundmn many is reco'n'nended (Dr uHernme designs EV Laser cumrq opc'mvcs wnn "apczmda wuHs and mo rouncmq corners wm am bcncr dosxc readscv Cdstomcrs shou‘c can thew Guard asse’na‘y me for Ska design recom’nencnhons EXONP‘S s‘ercﬂ des‘g’v baSeC on a 50% vo‘umemc \Dud su‘der paste M‘cr m H’C’ bk) Var other S‘cncﬂ rccowmcwdatnrs. ' hams Q‘ INSTRUMENTS www.li.com

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE

DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”

AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD

PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate

TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable

standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you

permission to use these resources only for development of an application that uses the TI products described in the resource. Other

reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third

party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,

damages, costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on

ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable

warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265