SVH1920v2 Manual Datasheet by Digital View Inc.

View All Related Products | Download PDF Datasheet
IO '5 l—l .)> '< l="">
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
1 of 60
PC, DVI, VIDEO, HD Component INTERFACE CONTROLLER
FOR TFT PANEL
Model: SVH-1920v2
Part number : 41752004X-3 or up
INSTRUCTIONS
CONTENTS
Page: 2. Introduction, How to Proceed, Usage Note, Disclaimer
3. System design – Diagram of a suggested system
4. Assembly notes – Important information about system elements
6. Connection & Operation – How to use the controller
13. Connectors, pinouts & jumpers – Essential connection information
27. Controller dimensions
28. Application notes
30. Troubleshooting
31. Specifications
32. Appendix I – Supported graphics modes table
35. Appendix II – RS-232 control protocols
48. Appendix III Mapping definition
52. Appendix IV – Auto Color Gain
53. Appendix V – DV remote control unit work for SVH-1920v2
54. Appendix VIIPIP mix table
55. Appendix VIIHD-1000 / HD-2000 connection
56. Appendix VIII – Procedure for showing how to select the baud rate
58. Warranty, Caution & Limitation of Liability, Trademarks
59. Contact details
60. Revision History
It is essential that these instructions are read and understood before connecting or
powering up this controller.
See at : hngz/lwww dig\la‘vwewLum/cumw‘lsvs/csg Eng
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
2 of 60
Introduction
Designed for LCD monitor and other flat panel display applications, the SVH-1920v2 is a feature rich interface
controller for :
TFT (active matrix) LCD panels of 1920x1200, 1920x1080, 1920x480, 1600x1200, 1600x900, 1680x1050, 1440x900,
1366x768, 1280x1024, 1280x800, 1280x768 1024x768, 1024x600, 800x600, 800x480 and 640x480 resolutions.
Computer video signals of VGA, SVGA, XGA, SXGA, WXGA, UXGA, WUXGA standard.
Video signals of NTSC, PAL and SECAM standard.
DVI input support up to 1920x1200 60Hz input signals
HD-SDI input support by using optional HD-SDI adaptor board (Kit P/N 546013410-3 / P/N 546013310-3 )
Ordering information :
Controller Part number Ordering part number
SVH-1920v2 P/N 41752004X-3 P/N 4175200XX-3
HOW TO PROCEED
Ensure you have all parts & that they are correct, refer to:
Connection diagram
Connector reference (in following section)
Assembly notes (refer to page 4 – 5)
Check controller switch & jumper settings (errors may damage the panel)
Prepare the PC
Connect the parts
Understand the operation & functions
IMPORTANT USAGE NOTE
This equipment is for use by developers and integrators, the manufacturer accepts no liability for damage or injury
caused by the use of this product. It is the responsibility of the developer, integrators or other user of this product to:
Ensure that all necessary and appropriate safety measures are taken.
Obtain suitable regulatory approvals as may be required.
Check power settings to all component parts before connection.
DISCLAIMER
There is no implied or expressed warranty regarding this material.
Controller Solution Generator
Full web resource matching controllers & panels with connection diagrams for download.
See
at
:
ht
tp://www.digitalview.com/controllers/csg.php
LCD PANEL \NVERTER CABLE 41 0PTTONAL LED OPTTCNAL TR SENSOR 43 D‘SPLAYFCRT EXTERNAL PANEL FUNCT‘UN 2ANEL CABLE p T FOR was FANEL OUT LT POWER ‘NPUT EXTERNAL PANEL CONTROLS POWER OUTPUT R5721: comm HAW": ML", PUNCTTON TNTEREAOE (3;. pm CONNECT To HDrSDTlé §[ COW/13g ADAPTOR BOARD @ ‘ H (HD71000/HD72OOU) LCD EOPT‘ONAL HD COMPONENT A CONTROLLER AUDTO VHJEC TNPUT L ADAPTOR BACKLTOHT STATUS BOARD ‘NPUT "SW“! (NOT AMBTENT LN;HT 4w.“ ‘1‘“ ESUFF‘ORT SENSOR CONNEOTTON —‘ Now) VGA 2 TNPUT DVH (VGA 2 U AUXHJARY /DvPB) TNPUT +5VDC OUTPUT VGA T TNPUT DC Tzv/zw, ALTERNATE AJXHJARY POWER \NPUT COMPOSTTE T A; vTDEO TNPUT SiV‘DEO T TNPUT (COMPOSTTE SrVTDEo T TNPUT L“ AND rx/TDED TM) CDMPDSTTE T \NPLT
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
3 of 60
SYSTEM DESIGN
A typical LCD based display system utilizing this controller is likely to comprise the following:
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
4 of 60
ASSEMBLY NOTES
This controller is designed for monitor and custom display projects using 1920x1200 or 1920x1080 or 1600x1200 or 1600x900
or 1680x1050 or 1440x900 or 1366x768 or 1280 x 1024 or 1280x800 or 1024 x 768 or or 1024x600 or 800x600 or 800x480 or
640x480 resolution TFT panels with a VGA, SVGA, WXGA, XGA, SXGA, UXGA or WUXGA signal input. The following
provides some guidelines for installation and preparation of a finished display solution.
Preparation: Before proceeding it is important to familiarize yourself with the parts making up the system and the various
connectors, mounting holes and general layout of the controller. As much as possible connectors have been labeled. Guides
to connectors and mounting holes are shown in the following relevant sections.
1. LCD Panel: This controller is designed for typical LVDS interfaced panels with panel voltage 3.3V, 5V or 12V, External for
12V~18V interface. Due to the variation between manufacturers of panels signal timing and other panel
characteristics,
factory setup and confirmation should be obtained before connecting to a panel. (NOTE: Check panel power jumper
settings before connection)
2. Controller: Handle the controller with care as static charge may damage electronic components. Make sure correct
jumper and dip switches settings to match the target LCD panel.
3. LCD signal cable (LVDS panel): In order to provide a clean signal it is recommended that LVDS signal cables are no
longer than 46cm (18 inches). If those wire cabling is utilized these can be made into a harness with cable ties. Care
should be taken when placing the cables to avoid signal interference. Additionally it may be necessary in some systems
to add ferrite cores to the cable to minimize signal noise.
5. Inverter: This will be required for the backlight of an LCD, some LCD panels have an inverter built in. As LCD panels
may have 1 or more backlight tubes and the power requirements for different panel backlights may vary it is important to
match the inverter in order to obtain optimum performance. See Application notes page 18 for more information on
connection.
6. Inverter Cables: Different inverter models require different cables and different pin assignment. Make sure correct cable
pin out to match inverter. Using wrong cable pin out may damage the inverter.
7. Function Controls: The following section discusses the controls required and the section on connectors provides the
detail. The controls are minimal: On/Off, Backlight Brightness (depends on inverter), OSD (5 momentary buttons) analog
VR type or (8 momentary buttons) digital type.
The 8 momentary buttons OSD switch mount P/N 416100520-3 or OSD membrane interface P/N 416100120-3 must be
used when 24VDC input.
8. Function controls cable: The cables to the function switches should be of suitable quality and length so that impedance
does not affect performance. Generally lengths up to 1 meter (3 feet) should be acceptable.
9. Status LED: The pin direction of the LED should be corrected for right colour indication. Red colour stands for standby.
Green colours stands for signal on. The status LED is an optional part only, can be unconnected.
10. IR sensor: It is an optional part only, can be unconnected if not using IR remote control. See Appendix V in details.
11. RS-232 control interface : Firmware upgrade and serial control via CN8 interface port.
12. Audio add-on board P/N 416940020-3: The audio add-on board gives the audio input and output signal connection. It is
an optional part only, can be unconnected if not using audio.
13. VGA Input Cable: Plug the VGA cable to the connector P1 (for VGA 1) or P2 / CN6 (for VGA 2) on the controller board.
As this may affect regulatory emission test results and the quality of the signal to the controller a suitably shielded cable should
be utilized.
14. DVI-D input cable : Plug the DVI cable to the connector P2 on the controller board.
15. Composite video input : Standard Composite cables can be used. Reasonable quality cable should be used to avoid
image quality degradation.
16. S-Video input : Standard S-video cables can be used. Reasonable quality cable should be used to avoid image quality
degradation.
17. Alternate composite 1 and S-video 1 input : Plug the video input cable P/N 426000500-3 on CNV1 connector
18. HD component video input : Plug the component video input cable P/N 426000600-3 on CNV2 connector
5460133‘073
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
5 of 60
20. Interface for connecting to HD-SDI adaptor board
HD-SDI (1-in-1-out) adaptor board, Kit number P/N 546013410-3 includes :
HD-1000 adaptor (1-in-1-out) P/N 416013410-3
Ribbon cable P/N 426171120-3, 180mm
HD-SDI (2-in-2-out) adaptor board, Kit number P/N 546013310-3
includes :
HD-2000 adaptor (2-in-2-out) P/N 416013310-3
Ribbon cable P/N 426171120-3, 180mm
21. Power Input: 12V/24VDC is required, this should be a regulated supply. The power rating is depending on the panel and
inverter used. Normally, power supply with 3.5Amp current output should enough for most of 4x CCFT panels. Although the
controller provides power regulation for the LCD power this does not relate to the power supplied to the backlight inverter. If an
unregulated power supply is provided to an inverter any fluctuations in power may affect operation, performance and lifetime of
the inverter and or backlight tubes.
22. External panel power input : Allow to supply external power to the panel separately for max 3.3V (7A) or 5V (7A) or 12V
(5A) or 18V (3.5A) via PP4 power input connector.
23. Auxiliary video input : This port provides Composite video 1 & 2, S-video 1 & 2. The video input selection can be
switched via RS-232 command (0x98).
24. Auxiliary +5VDC output : 2 ways connector provides +5VDC output.
25. Ambient light sensor connection : 3 ways connector provides interface for ambient light sensor connection.
26. Backlight status input : 2 ways connector provides interface for connection with panel which support the panel with
backlight status monitoring function.
Power output: Note the controller has an overall 3Amp current limit and the current available from the auxiliary power
output will be dependent on the power input and other system requirements.
Power Safety: Note that although only 12V / 24VDC is required as ‘power-in’ a backlight inverter for panel backlighting
produces significantly higher voltages (the inverter does not connect to the ground plane). We strongly advise
appropriate insulation for all circuitry.
EMI: Shielding will be required for passing certain regulatory emissions tests. Also the choice of external Controller to PC
signal cable can affect the result.
Ground: The various PCB mounting holes are connected to the ground plane.
Servicing: The board is not user serviceable or repairable. Warranty does not cover user error in connecting up to the
controller and is invalidated by unauthorized modification or repairs.
Controller Mounting: It is recommended that a clearance of at least 10mm is provided above and 5mm below the
controller when mounted. Additionally consideration should be given to:
Electrical insulation.
Grounding.
EMI shielding.
Cable management. Note: It is important to keep panel signal cables apart from the inverter & backlight cables to
prevent signal interference.
Heat & Ventilation: Heat generated from other sources, for example the backlight of a very high brightness panel
may generate significant heat which could adversely affect the controller.
Other issues that may affect safety or performance.
PC Graphics Output: A few guidelines:
Signal quality is very important, if there is noise or instability in the PC graphics output this may result in visible noise
on the display.
Refer to graphics modes table in specifications section for supported modes.
Non-interlaced & interlaced video input is acceptable.
IMPORTANT: Please read the Application Notes section for more information.
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
6 of 60
CONNECTION & OPERATION
CAUTION: Never connect or disconnect parts of the display system when the system is powered up as this may cause serious
damage.
CONNECTION
Connection and usage is quite straight forward (it is useful to have the relevant connection diagram available at this time):
1. LCD panel & Inverter: Connect the inverter (if it is not built-in the panel) to the CCFT lead connector of the LCD panel.
LVDS type panels: The controller board has the built-in LVDS transmitter driver. Plug the LVDS cable to J3. Insert the
panel end of the cable the LCD panel connector.
2. Inverter & Controller: Plug the inverter cable to CNB1 and CNA1 (if necessary). Plug another end to the connector on
the inverter.
3. Function switch & Controller: Plug the OSD switch mount cable to CNC1 on the controller board and another to the
OSD switch mount.
4. LED & Controller: Plug in a 3-way with dual colour LED to connector LED1 on the controller board.
5. IR & Controller: Plug in a 3-way with IR sensor to connector IR1 on the controller board.
6. Jumpers & Switches: Check all jumpers and switches (SW3, SW4) are set correctly. Details referring the connection
diagram (a separate document) or the jumpers and switches setting table (in the following section).
7. Jumpers & Inverter & Panel voltage: Particularly pay attention to the settings of JA3, JA5, JA6, JB2 and JB3. JB2 &
JB3 are used for inverter control (read inverter specification and information on the jumper table to define the correct
settings). JA3 & JA5 & JA6 is used for panel voltage input (read panel specification and information on the jumper table
to define the correct settings).
8. VGA cable & Controller: Plug the VGA cable to the connector P1 on the controller board. VGA 2 is supported via P2
(DVI-I) or CN6 connector.
9. DVI cable & Controller : Plug the DVI cable to the connector P2 on the controller board.
10. Power supply & Controller: Plug the DC 12V/24V power in to the connector PP5 or PP2. You can consider to use
DigitalView mating power cable P/N 426013800-3, 160mm for PP5 connection.
11. External panel power input : Plug power cable : P/N 426013700-3 for external panel power input (3.3 (max 7A) / 5V
(max 7A) / 12V (max 5A) / 18V (max3.5))
12. Power on: Switch on the controller board and panel by using the OSD switch mount.
LED status (LED1) :
State LED color
Backlight OFF RED
Backlight ON GREEN
General:
If you are using supplied cables & accessories, ensure they are correct for the model of panel and controller.
If you are making your own cables & connectors refer carefully to both the panel & inverter specifications and the section
in this manual, “Connectors, Pinouts & Jumpers” to ensure the correct pin to pin wiring.
PC SETTINGS
The controller has been designed to take a very wide range of input signals however to optimize the PC’s graphics
performance we recommend choosing 60Hz vertical refresh rate – this will not cause screen flicker.
OPERATION
Once the system has been connected and switched on there are a number of functions available to adjust the display
image as summarized in the following sections. The settings chosen will be saved for each mode independently.
EWSHNEES E E E 5““ E |:| UA‘DFF AFN“ , |:| + ESL DN
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
7 of 60
LCD DISPLAY SYSTEM SETTINGS
NOTE: By way of explanation the following refers to a set of sample buttons that may be obtained as an option. In
addition to power on/off and connection for backlight brightness the controller provides an On Screen Display of certain
functions which are controlled by 5 momentary type buttons (analog VR type) or 8 momentary type buttons (digital type):
Controls Analog VR type Digital type
On/Off – turns controller board power on VR toggle switch On/Off button
Brightness – controls backlight brightness Rotary VR Brightness +/- buttons
Menu
Turns OSD menu On or Off (it will auto time
off)
Back to previous OSD menu page
Menu button Menu button
Select down
Moves the selector to the next function (down)
SEL DN SEL DN
Select up
Moves the selector to the previous function
(up)
SEL UP SEL UP
+
Increase the OSD parameter values
Go into the sub-menu page from the top
Confirm to select the OSD function
+ +
-
Decrease the OSD parameter values
- Go into the sub-menu page from the bottom
- -
Reset to Factory Defaults Press and hold SEL DN button,
then power on the controller
Press and hold SEL DN
button, then power on the
controller
Access “Programming Mode” Press and hold MENU button,
then power on the controller
Press and hold MENU button,
then power on the controller
ON/Off/Brightness
SEL UP
SEL DN
+
-
Menu
Analog VR type
Digital type
12V / 24VDC power input :
Analog 10K VR Type OSD
switch mount uses
P/N 410680550-3 or up
12V / 24VDC power input :
Digital 10K Type OSD
switch mount uses
P/N 416100520-3 or up
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
8 of 60
Picture :
Volume
###
Increase/decrease volume level, total: 100 steps
Brightness Increase/decrease panel brightness level, total: 100 steps
Contrast Increase/decrease panel contrast level, total: 100 steps
Saturation Increase/decrease saturation, total: 100 steps
Hue ** Increase/decrease Hue level, total: 100 steps
Sharpness Increase/decrease sharpness, total: 30 steps
Backlight Backlight brightness adjustment (Functions when
light detector sets OFF)
Position
##
Aspect / Size 4
44
4
- Fill Screen : Enable full screen expansion for lower resolution Image
- Fill to Aspect Ratio: Enable fill screen expansion for lower resolution
image according to aspect ratio
- 4 : 3 : scaling format in 4:3
- 16 : 9 : scaling format in 16:9
- 16 : 10 : scaling format in 16:10
- 2.35 : 1 : scaling format in 2.35:1
- 2 : 1 : scaling format in 2:1
- 1 : 1 : Display the exact image resolution on the screen without
image expansion.
** : FUNCTION IN ARGB/ DVI / VIDEO NTSC MODE ONLY
## : FUNCTION IN ARGB MODE ONLY
### : DISPLAY WHEN AUDIO ADD-ON BOARD CONNECTED
Move the image position upward
Move the image position downward
Move the image position to the left
Move the image position to the right
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
9 of 60
Source : Select the input video signal
Main Port Change 4
VGA 1
VGA 2
DVI
Composite 1
Composite 2
S-Video 1
S-Video 2
Component 1
HD/SD SDI 1
++
HD/SD SDI 2
++
PIP Port change4
PIP Off / VGA 1/ VGA 2/ DVI / Composite 1 / Composite 2 / S-Video 1 / S-Video 2 /
Component 1 / HD/SD SDI 1 / HD/SD SDI 2
PIP Size4: Off / PIP Size 1~18 / Size by Size / Size by Size Tall
The PIP capability on display input sources refer to Appendix VII – PIP mix table
PIP Position :
PIP Blend Level : 6.25% ~ 100% : PIP Transparency
PIP Swap : Swap between the main window and PIP window
PIP Auto Turn off : : OFF / ON
ON : When PIP is no signal input after 30 seconds, the PIP
window will turn off automatically.
OFF : PIP window keeps on
++ DISPLAY WHEN HD-1000/-2000 CONNECTED
Utilities :
Setup 4
Auto Picture Setup
#
: Auto adjust the image position, phase and size
Auto Color Gain
+
4
44
4 : Auto Color Calibration (See appendix IV)
- Return
- Execute
Wide Screen Mode Selection
#
4
44
4 : Recognize the wide screen mode coming from ARGB port
- Group 1
- 1024x768
- 1280x768
- 1360x768
- 1366x768
- Group 2
- 1440x900
- 1600x900
Manual Clock
#
: Adjust the image horizontal size
Manual Phase
#
: Fine tune the data sampling position (adjust image
quality)
Auto Source Seek :
- Auto : : OFF / ON
ON – Auto source select always enable
OFF – Disable auto source select function
- Setup4
44
4 Selection for the corresponding input sources detection
VGA 1
Move the PIP position upward
Move the PIP position downward
Move the PIP position to the left
Move the PIP position to the right
34:3” Sam;
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
10 of 60
VGA 2
DVI
Composite 1
Composite 2
S-Video 1
S-Video 2
HD/SD SDI 1
++
HD/SD SDI 2
++
The corresponding input port name display on OSD menu will disappear once
setting “OFF”.
Auto Power : OFF / ON
ON – Enable soft power off function if absence of input signals
OFF – Disable soft power function
Video Standard (SD)
+++
4
AUTO
NTSC*
NTSC 4.43*
PAL*
PAL M*
SECAM*
(* - No image found when non-matching video system signal input)
Anti Image Retention :
Anti Image Retention :
Method : Flash / Pixel Shift / Horizontal Pan / Vertical Pan
Flash : Flashing the screen
Pixel Shift : Image shift pixel by pixel around the screen
Horizontal Pan : Display a pattern moving horizontally on screen.
Vertical Pan : Display a pattern moving horizontally on screen.
Horizontal Pan Setting :
Height > Panel Height : ÷2 / ÷4 / ÷6 / ÷8 : Configure the pattern height
Width > Panel Width : ÷2 / ÷4 / ÷6 / ÷8 : Configure the pattern width
Pattern : Black / White : Configure the pattern color
Pass : 1 ~ 100 : Configure the pattern moving cycle
Vertical Pan Setting :
Height > Panel Height : ÷2 / ÷4 / ÷6 / ÷8 : Configure the pattern height
Width > Panel Width : ÷2 / ÷4 / ÷6 / ÷8 : Configure the pattern width
Pattern : Black / White : Configure the pattern color
Pass : 1 ~ 100 : Configure the pattern moving cycle
Flash Setting :
Timer : 1 ~ 100s : Configure the flashing duration
Flash Period : 1 ~ 100 : Configure the flashing cycle
Note : Anti Image retention state will be cleared once you press the MENU button.
Gamma : 1.8 / 1.9 / 2.0 / 2.1 / 2.2 / 2.3 / 2.4 / 2.5 / 2.6 (default 2.2)
(Effective on V1.27.00.00 or later firmware revision)
Image Orientation** 4
Normal
Horizontal Flip
Vertical Flip
Rotate
OSD 4
OSD position :
OSD Timeout (sec) : ON – 60 : Adjust the OSD menu timeout period in a step of 5
Move the OSD menu image position upward
Move the OSD menu position downward
Move the OSD menu position to the left
Move the OSD menu position to the right
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
11 of 60
seconds (max 60 seconds)
ON =
Continuous to display OSD menu.
60 = 60 seconds later will turn off the OSD menu.
Language : English / Spanish / French / German / Chinese :Select OSD menu language
display
Display Input : OFF / ON : Display input source info after switching source.
IR Remote control : IR Remote Enable : Set enable on IR remote control
IR Remote Disable : Set disable on IR remote control
Freeze : Freeze the image (use “+” button)
Zoom 4
Zoom level : : Enable the zoom in function on the image displayed.
Use “+” button to zoom in the image
Use “-“ button to decrease the zoomed image
Horizontal pan : : Pan the image horizontally
Vertical pan : : Pan the image vertically
Factory Reset
Note : Freeze state will be cleared when you using zoom function.
Color Temperature 4
5000K
Red Gain :
Green Gain :
Blue Gain :
Red Offset :
Green Offset :
Blue Offset :
Reset to Defaults : Resume to the default values
6500K
Red Gain :
Green Gain :
Blue Gain :
Red Offset :
Green Offset :
Blue Offset :
Reset to Defaults : Resume to the default values
8000K
Red Gain :
Green Gain :
Blue Gain :
Red Offset :
Green Offset :
Blue Offset :
Reset to Defaults : Resume to the default values
9300K
Red Gain :
Green Gain :
Blue Gain :
Red Offset :
Green Offset :
Blue Offset :
Reset to Defaults : Resume to the default values
User setting :
Red Gain :
Green Gain :
Blue Gain :
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
12 of 60
Red Offset :
Green Offset :
Blue Offset :
Reset to Defaults : Resume to the default values
Reset All to Defaults : Resume all color temperature settings to the default values.
Hot Key 4
Hot key 1 : Brightness / Contrast / Inputs / Aspect Ratio/ Zoom / Freeze / PIP Size / PIP Swap
/ PIP ON/OFF / Saturation / Hue / Backlight / Auto Picture Setup / Image Orientation*** /No
Function
Hot key 2 : Brightness / Contrast / Inputs / Aspect Ratio/ Zoom / Freeze / PIP Size / PIP Swap
/ PIP ON/OFF / Saturation / Hue / Backlight / Auto Picture Setup / Image Orientation*** / No
Function
Monochrome Mode4 (Effective on V1.26.00.00 or later firmware revision)
- Color
- Red Monochrome
- Green Monochrome
- Blue Monochrome
- Red Only (Display when JP4 position 5-6 is closed)
- Green Only (Display when JP4 position 5-6 is closed)
- Blue Only (Display when JP4 position 5-6 is closed)
Backlight Setup4
44
4
- B/L Invert : : Invert for the backlight brightness
-
B/L Control : D/A / PWM : Selection for voltage level dimming control / PWM
dimming control
- Backlight Frequency : 100 ~ 440Hz in a step of 20
- Light Detector : : Enable ambient light detector function by using KIT
70220-3
- Min Backlight Level : 0 ~ 50% : Default the minimum backlight adjustment.
Default Setting 4
44
4
Reset to Factory Defaults 4
44
4 (Activate when JC1 position 4 sets open)
Are you sure ? Yes/No
Reset to Factory Defaults with (Color Temp.) 4
44
4 (Activate when JC1 position 4 sets open)
Are you sure ? Yes/No
Save Current Settings as Calibrated Values 4
44
4 (Activate when JC1 position 2 sets closed)
Are you sure ? Yes/No
Recall Stored Calibrated Values 4
44
4
Are you sure ? Yes/No
# : DISPLAY IN ARGB MODE ONLY
+ DISPLAY IN ARGB & COMPONENT MODE ONLY
++ DISPLAY WHEN HD-1000/-2000 CONNECTED
+++ DISPLAY IN COMPOSITE & S-VIDEO MODE ONLY
** The image orientation function is not support under the following conditions :
- PIP
- Component 1 (via CNV2 connector) input.
- Driving with 1366x768 panel
- Zoom
*** Support on V1.26.00.00 firmware or later version.
Once it selects the image orientation on hotkey 1 or hotkey 2, it will cycle
through the 4 image orientation modes (Normal/Horizontal Flip/Vertical
Flip/Rotate) by pressing each time of hotkey button (SEL UP/SEL DN or + /
- buttons).
Not support rotate mode when running with PIP mode or Component input.
Firmware V1.27.00.00 or up
54:11.11 1111 SW 11111111111 SW1 "A CHE! SVH’1920VL 15 T ‘ 1mm L7R+4Lur§¢ug I”B ~85 vB7 EN?
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
13 of 60
CONNECTORS, PINOUTS & JUMPERS
The various connectors are:
Summary: Connectors
Ref Purpose Description
CN1 Second RS-232 serial control JST 6-way, B6B-XH-A (Matching type : XHP-6)
CN3 Panel connector HIROSE DF20G-10DP-1V (Matching type : DF20A-10DS-1C)
CN6 VGA 2 input connector Hirose 12-pin, DF11-12DP-2DSA (Matching type : DF11-12DS-2C)
CN7 Audio board connector DIL socket header 5x2 right angle
(Matching audio Add-on Board P/N 416940020-3)
CN8 RS-232 serial control JST 6-way, B6B-XH-A (Matching type : XHP-6)
CN9 Ambient light sensor connector JST 3-way, B3B-PH-K (Matching type : PHR-3)
CNA1 Auxiliary power output JST 4-way, B4B-XH-A (Matching type : XHP-4)
CNA2 Auxiliary +5VDC output JST 2 way, B2B-PH-K (Matching type : XHP-2)
CNB1 Backlight inverter JST 5-way, B5B-XH-A (Matching type : XHP-5)
CNB2 Backlight status input connector JST 2 way, B2B-XH-A (Matching type : XHP-2)
CNC1 OSD controls Hirose DF13-12P-1.25H (Mating type : DF13-12S-1.25C)
(Matching OSD switch mount cable P/N 426122200-3 (150mm) or
426122210-3 (250mm)
CNV1 Alternate video in (Composite 1 & S-
Video 2)
JST 5-way, B5B-PH-K (Matching type : PHR-5)
(Matching video cable P/N 426000500-3)
CNV2 Component (YPbPr) video input
connector:
JST 6-way, B6B-PH-K (Matching type : PHR-6)
CNV5 Auxiliary video input (Composite 1&2,
S-Video 1&2)
Header pin 13x2 (Matching video cable P/N 426000800-3)
J1 S-video 1 in Mini din 4-way
J2 Composite video 1 in BNC connector
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
14 of 60
J3 Panel signal for LVDS panel JAE FI-RE51S-HF (Matching type : FI-RE51HL)
J4 HD-SDI adaptor board interface
connector
2 x 25 ways, 2.54x1.27 header
(Matching connector type : DF13-40DS-1.25C)
(Matching ribbon cable : P/N 426171100-3)
J5 Display port output for panel
connection
I-PEX 20455-030E-12 (Matching type : I-PEX 20454-030T)
J6 Panel power output for Disport port
interface panel use.
JS-1147A-08 Top 1.25mm (Matching type : Molex 51021-0800)
IR1 Infra-Red sensor connector JST 3-way, B3B-XH-A (Matching type : XHP-3)
LED1 Dual color LED connector JST B3B-XH-A (for 4x-3 or up version) (Matching type : XHP-3)
P1 VGA analog input DB-15 way high density 3 row
P2 DVI-I (DVI-D or VGA 2) input DVI-I connector
PP2 Power input (alternative) DC power Molex 2 pin 0.156” pitch
PP4 External panel power input Molex 43045-0400 compatible
(Matching connector type : Molex 43025-0400 compatible)
(Matching power cable : P/N 426013700-3)
PP5 Power input Molex 43650-0200 compatible
(Matching connector type : Molex 43645-
0200 compatible)
(Matching power cable : P/N 426013800-3)
Summary: Jumpers setting
Ref
Purpose Note
JA3 Panel power voltage select
CAUTION: Incorrect setting can damage
panel
See panel voltage setting table 1
JA5 Panel power voltage select
CAUTION: Incorrect setting will cause panel
damage
See panel voltage setting table 1
JA6 Panel power voltage select
CAUTION: Incorrect setting will cause panel
damage
See panel voltage setting table 1
JB1 Backlight brightness voltage range 1-2 closed = 5V max
2-3 closed = 3.3V max
JB2 Backlight inverter on/off control – signal
level
2-3 = On/Off control signal ‘High’ = +5V
1-2 = On/Off control signal ‘High’ = +3.3V
Open = On/Off control signal ‘High’ = Open collector
CAUTION: Incorrect setting can damage inverter.
JB3 Backlight inverter on/off control – polarity 1-2 = control signal ‘high’ = CCFT ON
2-3 = control signal ‘low’ = CCFT ON
JB4 GPIO pins voltage selection 1-2 = 3.3V
2-3 = 5V
JB5 Backlight control type selection 1-2 = VR/Digital switch mount control
3-4 = Analog backlight brightness - voltage range 0~5V
5-6 = PWM (Pulse Width Modulation) brightness
JB7 Backlight control voltage on CNB1 pin 4
(Function when JB5 sets 1-2 closed)
Open = For OSD switch mount control (Default)
1-2 = 0V
2-3 = 3.3V / 5V controlled by JB1
JC1 Custom configuration Position 1 :
Closed = Disable B/L setup menu
Position 2 :
Closed = Enable save Current Settings as Calibrated
Values on OSD menu
Position 3 :
Closed = Enable baud rate selection function in
programming mode
Position 4 :
Closed = Hide “Reset to Factory Defaults” and “Reset to
Factory Defaults with (Color Temp.)” from OSD menu.
Position 7 :
Closed = Enable for selection of the “RM-DN5
Assembly” menu on Programming mode.
JC2 Custom configuration Position 1 : Enable J3 – pin 16 (OP1) controlled by JB4
Position 2 : Enable J3 – pin 17 (OP2) controlled by JB4
JP4 Custom configuration 1-2 closed = Reserved
3-4 closed = On-board programming
5-6 closed = Display "Red/Green/Blue only selection
under Monochrome mode on OSD menu
JP6 Input power control Short = External switch control
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
15 of 60
Open = Switch mount control
JP9 Factory use Default Open
JT1 Composite video-in terminator enable Open = composite video 1 input is not terminated
Close = composite video 1 input is terminated with 75
JT2 S-Video luma-in terminator enable Open = S-video 1 luma input is not terminated
Close = S-video 1 luma input is terminated with 75
JT3 S-Video chroma-in terminator enable Open = S-video 1 chroma input is not terminated
Close = S-video 1 chroma input is terminated with 75
JT4 Component luma-in terminator enable Open = S-video 2 luma input is not terminated
Close = S-video 2 luma input is terminated with 75
JT5 Component Cr-in terminator enable Open = S-video 2 chroma input is not terminated
Close = S-video 2 chroma input is terminated with 75
JT6 Component Cb-in terminator enable Open = composite video 2 input is not terminated
Close = composite video 2 input is terminated with 75
SW3 Panel & function selection See table 2
SW4 Panel & function selection See table 3
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
16 of 60
Table 1 : Panel voltage setting table :
Input voltage via
PP2, PP5 Panel Voltage JA3 JA5
JA6 Jumper on board
12VDC
3.3V 3V3 closed
1-3 & 2-4 1-3 & 2-4
5V 5V closed 1-3 & 2-4 1-3 & 2-4
12V OPEN 1-3 & 2-4 5-7 & 6-8
CAUTION: Incorrect setting can damage panel & controller
Input voltage via
PP2, PP5 Panel Voltage JA3
JA5 JA6 Jumper on board
24VDC**
3.3V 3V3 closed
1-3 & 2-4 1-3 & 2-4
5V 5V closed 1-3 & 2-4 1-3 & 2-4
10V 10V closed
1-3 & 2-4 3-5 & 4-6
12V 12V closed
1-3 & 2-4 3-5 & 4-6
18V
18V closed
1-3 & 2-4 3-5 & 4-6
CAUTION: Incorrect setting can damage panel & controller
** Ensure that the backlight inverter supports 24V operation prior to connecting a 24VDC input.
Because CNA1 pin 1 and CNB1 pin 2 will output 24VDC if input 24VDC via PP2/PP3 or PP5.
,z-n JAb.-u A52“- 'D- 2n- JAe‘u- 2n- JAS‘E 2n- JAe‘u- 2n- JAS‘E 2n- JAe‘u- 2n- JAS‘E
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
17 of 60
Input voltage via
PP4 Panel Voltage JA3
JA5 JA6 Jumper on board
3.3 / 5 / 12 /
18VDC*
3.3V OPEN 3-5 & 4-6 1-3 & 2-4
5V OPEN 3-5 & 4-6 1-3 & 2-4
10V OPEN 3-5 & 4-6 3-5 & 4-6
12V OPEN 3-5 & 4-6 3-5 & 4-6
18V
OPEN 3-5 & 4-6 3-5 & 4-6
* Maximum current for 3.3V, 5V = 7A, Maximum current for 12V = 5A, Maximum current for 18V =
3.5A
”5‘ CNN CHE S‘w’H719ZOvZ 11111 81 1 11111 C\ CNW 1:01 W JT TZJU JT‘HTSJT P1 J1 J2 -€19 it mm M CNm g [J3 JBS JEZ
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
18 of 60
JA3, JA5 & JA6 location on board : (Please pay attention to the jumper settings on JA3, JA5
& JA6 which are red in color)
!
!
JA3
JA6 & JA5
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
19 of 60
Table 2 : DIP Switch selection – SW3
Pos #1 Pos #2 Pos #3 Pos.#4 Description Panel resolution
For WUXGA panels
OFF ON ON OFF LG LM260WU1-SLB1 1920x1200
ON ON ON OFF LG LM240WU2-SLA1 1920x1200
OFF OFF OFF OFF Sharp LQ445D3LZ19 1920x1080
ON OFF OFF OFF Samsung LTA460H2-L02 1920x1080
OFF ON OFF OFF Sharp LQ170M1LZ04 1920x1200
ON ON OFF OFF Samsung LTA700HH-LH1 (1
st
trial testing) 1920x1080
OFF OFF ON OFF Samsung LTA700HH-LH1 (2
nd
trial testing) 1920x1080
OFF OFF ON ON AU Optronics P645HW03 V0 (1920x1080) 1920x1080
OFF OFF ON ON AU Optronics P645HW03 V0 1920x1080
OFF ON ON ON Samsung ASI545FB01-0 (OLED)* 1920x1080
For UXGA panels
OFF OFF OFF OFF Fujitsu FLC59UXC8V-02A 1600x1200
ON OFF OFF OFF Samsung LTM213U6-L01 1600x1200
For WXGA panels
OFF OFF OFF OFF LG LC420W02-A4 1366x768
ON OFF OFF OFF Sharp LQ315T3LZ24 1366x768
ON ON OFF OFF Samsung LTA320W2-L01 / LTA230W1-L02 1366x768
ON ON ON ON NEC NL12876BC26-21 / Samsung LTM170W1-L01 1280x768
OFF ON ON ON CHI MEI N154I4-L01 1280x800
OFF OFF ON OFF AU Optronics M190PW01 1440x900
OFF OFF ON ON Sharp LQ072K1LA03 1280x768
For SXGA panel
OFF OFF OFF OFF Sharp LQ181E1LW31 1280x1024
ON OFF OFF OFF AU Optronics M170EN05 1280x1024
ON ON OFF OFF Sharp LQ121S1LG81* 800x600
For XGA panel
OFF OFF OFF OFF Sharp LQ150X1LGN2A 1024x768
Sharp LQ150X1LGB1 1024x768
For SVGA panel
OFF OFF OFF OFF Sharp LQ121S1DG11/41 800x600
Toshiba LTM08C351 800x600
For WVGA panel
OFF OFF OFF OFF NEC NL8048BC24-01 800x480
ON OFF OFF OFF Kyocera TCG085WV1AB-G00 800x480
ON OFF ON OFF Sharp LQ070Y3LG4A 800x480
For VGA panel
OFF OFF OFF OFF Sharp LQ104V1DG51 640x480
ON OFF OFF OFF Sharp LQ104V1DG21 640x480
Kyocera TCG075VG2AC-G00 640x480
Others
OFF ON OFF OFF AU Optronics M201EW02 V8 1680x1050
ON OFF OFF ON Samsung LTM201M1-L01 1680x1050
OFF OFF ON ON Hitachi TX48D02VM0BAA / JDI TX48D02VM0BAA* 1680x1050
OFF OFF ON OFF Samsung LTI430LA01 1920x480
OFF ON ON OFF NEC NL10260BC19-01D 1024x600
ON ON ON OFF AU Optronics M200RW01 1600x900
Samsung LTM200KP01 1600x900
Remark :
* Effective on V1.26.00.00 version or up.
Remark : The above panel timings are generated based on the panel specification. Some of
the panel timings settings may not exactly to match the panel model we specified in this table.
Pos #5 Pos #6 Pos #7 Description
OFF OFF OFF WUXGA
ON OFF OFF UXGA
OFF ON OFF SXGA
ON ON OFF WXGA
OFF OFF ON XGA
ON OFF ON SVGA
OFF ON ON VGA
ON ON ON WVGA / Others
Pos. #8 Video lock ON – Disable : Always fix the output be 60Hz.
OFF – Enable : The output refresh rate locks to the input for 50Hz / 60Hz mode
(other resolution lock the output be 60Hz. )
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
20 of 60
Table 3 : DIP switch selection – SW4
Pos. # Function Description
1 Reserved Reserved
2 Panel pixel format OFF : Double Pixel
ON : Single Pixel
3 Panel selection Default ON : Single / Double pixel LVDS panel (controlled by SW4
position 2)
4 LVDS data mapping select
(Refer to Table 2)
If SW4 position 5 = OFF (8 bit)
OFF : Mapping B
ON : Mapping A
Please adjust to get the correct picture. See as Appendix I for details of
mapping of A and B.
If SW4 position 5 = ON (10 bit)
OFF : JEIDA (LVDS panel)
ON : VESA (LVDS panel)
Please adjust to get the correct picture. See as Appendix I for details of
mapping of VESA and JEIDA.
5 Output LVDS display mode selection OFF : 8 bit
ON : 10 bit
6 LVDS mapping swap OFF : Normal
ON : Swap
Support "Resolution default by EDID" for different resolution panel.
The controller will set the preferred timing based off the dip switch setting (SW3 position 1-7)
selection, but also be able to go higher to 1920x1200. For example, if the panel is a 1024x768 and the
dip switch setting are set for 1024x768. The preferred EDID resolution should be 1024x768. It should
also have the capability to set the max resolution to 1920x1200.
* This function is only effective on V1.26.00.00 or later firmware revision.
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
21 of 60
CN1 – Slave RS-232 serial control: JST B6B-XH-A (Matching type : XHP-6)
PIN SYMBOL DESCRIPTION
1 EXT_MSTR2_SCL Reserved
2 EXT_MSTR2_SDA Reserved
3 VCC +5V
4 TXD RS-232 Tx data
5 GND Ground
6 RXD RS-232 Rx data
CN3 – Panel connector: HIROSE DF20G-10DP-1V (Matching type : DF20A-10DS-1C)
PIN SYMBOL DESCRIPTION
1 OP1 Reserved
2 OP2 Reserved
3 OP3 Reserved
4 OP4 Reserved
5 IP1 Reserved
6 IP2 Reserved
7 IP3 Reserved
8 IP4 Reserved
9 EXT_MSTR2_SDA Reserved
10 EXT_MSTR2_SCL Reserved
CN6 - VGA 2 input connector : Hirose 12-pin, DF11-12DP-2DSA (Matching type : DF11-12DS-2C)
PIN SYMBOL DESCRIPTION
1 R Red, analog
2 DDC_5V +5V power supply for DDC (optional)
3 G Green, analog
4 GND Ground
5 B Blue, analog
6 GND Ground
7 HS Horizontal sync or composite sync, input
8 GND Ground
9 VS Vertical sync, input
10 DDC_SCL DDC serial clock
11 NC No connection
12 DDC_SDA DDC serial data
CN7 - Audio connector: DIL socket header 5x2 right angle
PIN SYMBOL DESCRIPTION
1 VCC Audio board logic power supply, +5V
2 VOLSEL0 Reserved
3 VOLSEL1 Reversed
4 TUNAUDSEL Reserved
5 CLK/CNT Reserved
6 GND Ground
7 +12V/+24V Audio board power supply, +12V/+24V
8 NC No connection
9 NC No connection
10 GND Ground
CN8 – RS-232 serial control: JST B6B-XH-A (Matching type : XHP-6)
PIN SYMBOL DESCRIPTION
1 SDATA Reserved
2 SCLK Reserved
3 VCC +5V
4 TXD RS-232 Tx data
5 GND Ground
6 RXD RS-232 Rx data
CN9 – Ambient light sensor connector : JST B3B-PH-K (Matching type : PHR-3)
PIN SYMBOL DESCRIPTION
1 GND Ground
2 VCC_5V VCC 5V
3 ALSF Ambient light sensing feedback
CN11 – SPDIF audio output connector : JST B3B-PH-K (Matching type : PHR-3)
PIN SYMBOL DESCRIPTION
1 SPDIF SPDIF Digital audio output
2 GND Ground
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
22 of 60
CNA1 - Auxiliary power output: JST B4B-XH-A (Matching type : XHP-4)
PIN SYMBOL DESCRIPTION
1 AUX 12V / 24V +12V / +24V DC
2 GND Ground
3 GND Ground
4 AUX 5V +5V DC, 500mA max
CNA2 - Auxiliary power output: JST B2B-PH-K (Matching type : XHP-2)
PIN SYMBOL DESCRIPTION
1 Vcc_5V +5V DC, 500mA max with fuse
2 GND Ground
CNB1 – Backlight inverter connector: JST B5B-XH-A (Matching type : XHP-5)
PIN SYMBOL DESCRIPTION
1 GND Ground
2 VBKL +12V / +24V DC, backlight power supply
3 BLCTRL On/Off control (enable) – see JB2 & JB3
4 BVR_WIP Brightness VR – WIP
5 BVR_A Brightness VR A
CNB2 – Backlight status input inverter connector: JST B2B-XH-A (Matching type : XHP-2 )
PIN SYMBOL DESCRIPTION
1 BL_STATUS Backlight status (Normal = High)
2 GND Ground
CNC1 – OSD switch mount control, Hirose DF13-12P-1.25H (Mating type : DF13-12S-1.25C)
PIN SYMBOL DESCRIPTION
1 PSWIN Power button A
2 SW_ON Power button B
3 BVR_A Backlight Brightness VR pin A
4 BVR_WIP Backlight Brightness R pin WIP
5 BVR_B Backlight Brightness VR pin B (470 ohm resistor to +5V Vcc)
6 GND Ground
7 MENU OSD menu
8 -/LEFT OSD -/Left
9 +/RIGHT OSD +/Right
10 SEL_DN OSD Select down
11 SEL_UP OSD Select up
12 NC No connection
The VR for brightness depends on the inverter. The main power load for On/Off is handled by a relay on the controller.
CNV1 – Alternate Video in input, JST B5B-PH-K (Matching type : PHR-5)
PIN DESCRIPTION
1 S-Video : Chroma in
2 S-Video : Luma in
3 Ground
4 Ground
5 Composite video in
CNV2 – Component (YPbPr) video input connector: JST 6-way, B6B-PH-K (Matching type : PHR-6)
PIN SYMBOL DESCRIPTION
1 A_Y1 Luma in / Green in
2 GND Ground
3 A_Pb1 Pb in / Blue in
4 GND Ground
5 A_Pr1 Pr in / Red in
6 GND Ground
VLCD LV VLCD LV VLCD LV VLCD LV
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
23 of 60
CNV5 – Auxiliary Video input connector, DIL socket header 13x2
PIN DESCRIPTION
1 S-Video : Chroma in
2 Ground
3 S-Video : Luma in
4 Ground
5 Composite video in
6 Ground
7 No connection
8 Ground
9 No connection
10 Ground
11 No connection
12 Ground
13 S-Video_2 : Chroma in
14 Ground
15 S-Video_2 : Luma in
16 Ground
17 Composite video in_2
18 Ground
19 No connection
20 Ground
21 No connection
22 Ground
23 No connection
24 Ground
25 No connection
26 Ground
IR1 – Infra-Red sensor connector: JST B3B-XH-A (Matching type : XHP-3)
PIN SYMBOL DESCRIPTION
1 GND Ground
2 STDBY_Vcc Stand by voltage
3 IR Data IR data
J3 – LVDS output connector: JAE FI-RE51S-HF (Matching type : JAE FI-RE51HL)
PIN SYMBOL DESCRIPTION
1 VLCD_HV Panel power supply (+12V / 18V) (selected by JA3, JA5 & JA6)
2 VLCD_HV Panel power supply (+12V / 18V) (selected by JA3, JA5 & JA6)
3 VLCD_HV Panel power supply (+12V / 18V) (selected by JA3, JA5 & JA6)
4 VLCD_HV Panel power supply (+12V / 18V) (selected by JA3, JA5 & JA6)
5 VLCD_HV Panel power supply (+12V / 18V) (selected by JA3, JA5 & JA6)
6 VLCD_LV Panel power supply (3,3V/5V) (selected by JA3, JA5 & JA6)
7 VLCD_LV
Panel power supply (3,3V/5V) (selected by JA3, JA5 & JA6)
8 VLCD_LV
Panel power supply (3,3V/5V) (selected by JA3, JA5 & JA6)
9 VLCD_LV
Panel power supply (3,3V/5V) (selected by JA3, JA5 & JA6)
10 VLCD_LV
Panel power supply (3,3V/5V) (selected by JA3, JA5 & JA6)
11 GND Ground
12 GND Ground
13 GND Ground
14 GND Ground
15 GND Ground
16 OP1 -
17 OP2 -
18 NC No function
19 NC No function
20 GND Ground
21 GND Ground
22 LVDS_OUT1_A4+ Positive differential LVDS data bit A4
23 LVDS_OUT1_A4- Negative differential LVDS data bit A4
24 LVDS_OUT1_A3+ Positive differential LVDS data bit A3
25 LVDS_OUT1_A3- Negative differential LVDS data bit A3
26 GND Ground
27 LVDS_OUT1_AC+ Positive LVDS clock for A channel
28 LVDS_OUT1_AC- Negative LVDS clock for A channel
29 GND Ground
30 LVDS_OUT1_A2+ Positive differential LVDS data bit A2
31 LVDS_OUT1_A2- Negative differential LVDS data bit A2
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
24 of 60
32 LVDS_OUT1_A1+ Positive differential LVDS data bit A1
33 LVDS_OUT1_A1- Negative differential LVDS data bit A1
34 LVDS_OUT1_A0+ Positive differential LVDS data bit A0
35 LVDS_OUT1_A0- Negative differential LVDS data bit A0
36 GND Ground
37 LVDS_OUT1_B4+ Positive differential LVDS data bit B4
38 LVDS_OUT1_B4- Negative differential LVDS data bit B4
39 LVDS_OUT1_B3+ Positive differential LVDS data bit B3
40 LVDS_OUT1_B3- Negative differential LVDS data bit B3
41 GND Ground
42 LVDS_OUT1_BC+ Positive LVDS clock for B channel
43 LVDS_OUT1_BC- Negative LVDS clock for B channel
44 GND Ground
45 LVDS_OUT1_B2+ Positive differential LVDS data bit B2
46 LVDS_OUT1_B2- Negative differential LVDS data bit B2
47 LVDS_OUT1_B1+ Positive differential LVDS data bit B1
48 LVDS_OUT1_B1- Negative differential LVDS data bit B1
49 LVDS_OUT1_B0+ Positive differential LVDS data bit B0
50 LVDS_OUT1_B0- Negative differential LVDS data bit B0
51 GND Ground
J4 – HD-SDI adaptor board interface connector: 2 x 25 ways, 2.54x1.27 header
(Matching ribbon cable : P/N 426171100-3)
PIN SYMBOL DESCRIPTION
1 GND Ground
2 GND Ground
3 CbCr0 (Input) CbCr0 (Input)
4 Y0 (Input) Y0 (Input)
5 CbCr1 (Input) CbCr1 (Input)
6 Y1 (Input) Y1 (Input)
7 CbCr2 (Input) CbCr2 (Input)
8 Y2 (Input) Y2 (Input)
9 CbCr3 (Input) CbCr3 (Input)
10 Y3 (Input) Y3 (Input)
11 CbCr4 (Input) CbCr4 (Input)
12 Y4 (Input) Y4 (Input)
13 CbCr5 (Input) CbCr5 (Input)
14 Y5 (Input) Y5 (Input)
15 CbCr6 (Input) CbCr6 (Input)
16 Y6 (Input) Y6 (Input)
17 CbCr7 (Input) CbCr7 (Input)
18 Y7 (Input) Y7 (Input)
19 CbCr8 (Input) CbCr8 (Input)
20 Y8 (Input) Y8 (Input)
21 CbCr9 (Input) CbCr9 (Input)
22 Y9 (Input) Y9 (Input)
23 N.C No connection
24 N.C No connection
25 VCC(5V) VCC(5V)
26 VCC (5V) VCC (5V)
27 CLOCK (Input) CLOCK (Input)
28 SCLK_TCK(control pin) SCLK_TCK(control pin)
29 GND Ground
30 SDIN_TDI(control pin) SDIN_TDI(control pin)
31 Field (Input) Field (Input)
32 SDOUT_TDO(control pin) SDOUT_TDO(control pin)
33 V sync (Input) V sync (Input)
34 CS_TMS(control pin) CS_TMS(control pin)
35 H sync (Input) H sync (Input)
36 GND Ground
37 DE (Input) DE (Input)
38 N.C No connection
39 N.C No connection
40 N.C No connection
41 HDSDI_LOCK (control pin) HDSDI_LOCK (control pin)
42 N.C No connection
43 GND Ground
44 GND Ground
45 N.C No connection
46 N.C No connection
DP PWR Powerlor cannecmv 3.3 v 500 mA Hum Hu‘fl Demm AUX CH n Auxm Channe‘ ne We AUX CH Auxn Channe‘ e CONFIGZ connec‘ed m Glound ML Lanes n LaneB n We ML Lanes LaneB osmve ML Lanez n Lanee n We ML Lane! Lane‘ osmve ML LaneD n Laneo n We ML LaneD Lane 0 osmve
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
25 of 60
47 N.C No connection
48 HDSDI_IPSEL (control pin) HDSDI_IPSEL (control pin)
49 Videomux_CAB (control pin) Video mux detected pin
50 HDSDI_CAB (control pin) HDSDI_CAB (control pin)
J5 – Display port output for panel connector:
I-PEX 20455-030E-12 (Matching type : I-PEX 20454-030T)
PIN SYMBOL DESCRIPTION
1 GND Ground
2 GND Ground
3 GND Ground
4 GND Ground
5 VLCD_LV Panel power supply (3,3V/5V) (selected by JA3, JA5 & JA6)
6 VLCD_LV Panel power supply (3,3V/5V) (selected by JA3, JA5 & JA6)
7 VLCD_LV Panel power supply (3,3V/5V) (selected by JA3, JA5 & JA6)
8 VLCD_LV Panel power supply (3,3V/5V) (selected by JA3, JA5 & JA6)
9 NC No connection
10
DP_PWR
Power for connector (3.3 V 500 mA)
11 Return Return for Power
12
Hot
Plug
Hot Plug Detect
13
AUX
CH
(n)
Auxiliary Channel (negative)
14 GND Ground
15
AUX
CH
(p)
Auxiliary Channel (positive)
16
CONFIG2
connected to
Ground
17 CONFIG1 connected to Ground
18
ML_Lane
3
(n)
Lane 3 (negative)
19 GND Ground
20
ML_Lane
3
(p)
Lane 3 (positive)
21
ML_Lane
2
(n)
Lane 2 (negative)
22 GND Ground
23 ML_Lane 2 (p) Lane 2 (positive)
24 ML_Lane 1 (n) Lane 1 (negative)
25 GND Ground
26
ML_Lane
1
(p)
Lane 1 (positive)
27
ML_Lane
0
(n)
Lane 0 (negative)
28 GND Ground
29
ML_Lane
0
(p)
Lane 0 (positive)
30 GND Ground
J6 – Panel power output: JS-1147A-08 Top 1.25mm (Matching type : Molex 51021-0800)
PIN SYMBOL DESCRIPTION
1 PVLCD_Low (3,3V/5V)
Panel power supply (3,3V/5V) (selected by JA3, JA5 & JA6)
2 PVLCD_Low (3,3V/5V)
Panel power supply (3,3V/5V) (selected by JA3, JA5 & JA6)
3 GND Ground
4 GND Ground
5 GND Ground
6 PVLCD_High (12V/18V)
Panel power supply (+12V / 18V) (selected by JA3, JA5 & JA6)
7 PVLCD_High (12V/18V)
Panel power supply (+12V / 18V) (selected by JA3, JA5 & JA6)
8 PVLCD_High (12V/18V)
Panel power supply (+12V / 18V) (selected by JA3, JA5 & JA6)
LED1 – Status LED connector: 3-pin header
PIN DESCRIPTION
1 Green LED pin (anode)
2 LED pin common (cathode)
3 Red LED pin (anode)
P1 - Analog VGA in - 15 way connector
PIN SYMBOL DESCRIPTION
1 PCR Red, analog
2 PCG Green, analog
3 PCB Blue analog
4 ID2 Reserved for monitor ID bit 2 (grounded)
5 DGND Digital ground
6 AGND Analog ground red
7 AGND Analog ground green
8 AGND Analog ground blue
9 DDC_5V +5V power supply for DDC (optional)
10 DGND Digital ground
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
26 of 60
11 ID0 Reserved for monitor ID bit 0 (grounded)
12 DDC_SDA DDC serial data
13 HS_IN Horizontal sync or composite sync, input
14 VS_IN Vertical sync, input
15 DDC_SCL DDC serial clock
P2 – DVI-I input
PIN SYMBOL DESCRIPTION
1 /RX2 TMDS Data 2-
2 RX2 TMDS Data 2+
3 GND Digital Ground
4 NC No connection
5 NC No connection
6 DDC_CLK DDC Clock
7 DDC_DAT DDC Data
8 VS_IN Analog vertical Sync
9 /RX1 TMDS Data 1-
10 RX1 TMDS Data 1+
11 GND Digital Ground
12 NC No connection
13 NC No connection
14 DDC_5V +5V power supply for DDC (optional)
15 GND Ground (+5, Analog H/V Sync)
16 HPD Hot Plug Detect
17 /RX0 TMDS Data 0-
18 RX0 TMDS Data 0+
19 GND Digital Ground
20 NC No connection
21 NC No connection
22 GND Digital Ground
23 RXC TMDS Clock+
24 /RXC TMDS Clock-
C1 R Red
C2 G Green
C3 B Blue
C4 HS_IN Analog horizontal sync
C5 GND Ground
C6 NC No connection
PP2 – Alternate 12V/24VDC input power supply
PIN DESCRIPTION
1 +12VDC / +24VDC in
2 Ground
PP4 – External panel power input
PIN DESCRIPTION
1 External panel power
2 Ground
3 External panel power
4 Ground
PP5 – 12V/24VDC input power supply
PIN DESCRIPTION
1 +12V / +24VDC
2 Ground
'— 179", [706] "—1669 [SSH—u “7854 [3 40179 476%” [P In!» 4‘10 [193] «3* % ass; [:14] , 32 mum K A L 954 474 Pan [[1911 L 1 [ ‘ J J V an [08714 we [3‘12] [3121 e30 [2‘56] 61 [024] V[ . b 44] ‘ ’51 [024] w ( 1 7 ‘ FEM) mnfi Q—J U W+L5 [101] w: 4 / “7705 [378] $32 [$01314 97948 [27414( [n31] E 0—0430 mam r163 [063] , ~\ 130 [(147] gm; ‘ WQ‘QQBKIQ} fl [m] $ 3 (3‘0 [ma] R 1—1 T 17 [1:711 Q m :l/www,di italviswcum/ mdums/svwezovzrwcdrcummner
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
27 of 60
CONTROLLER DIMENSIONS
Ready-made 3D Pro-E (SLDPRT) drawing files - Save time and effort for your system volumetric analysis design.
Includes jpg file previews. Please go to download at http://www.digitalview.com/products/svh-1920v2-lcd-controller
The maximum thickness of the controller is 20.7mm with or without video add-on board (measured from bottom of
PCB to top of components, including any underside components & leads). We recommend clearances of:
5mm from bottom of PCB - if mounting on a metal plate we also recommend a layer of suitable insulation
material is added to the mounting plate surface.
10mm above the components
3~5mm around the edges
Any of the holes shown above can be used for mounting the PCB, they are 3.2mm in diameter.
CAUTION: Ensure adequate insulation is provided for all areas of the PCB with special attention to high
voltage parts such as the inverter.
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
28 of 60
APPLICATION NOTES
USING THE CONTROLLER WITHOUT BUTTONS ATTACHED
This is very straightforward:
Firstly setup the controller/display system with the buttons. With controls attached and display system active make any
settings for colour, tint and image position as required then switch everything off.
Remove the control switches, the 12-way (CNC1) cable.
Use a jumper or similar to connect pins 1 & 2 on CNC1, this will fix the board On.
Refer to inverter specifications for details as to fixing brightness to a desired level, this may require a resistor, an open
circuit or closed circuit depending on inverter.
Summary: On CNC1 the only pins that are used are for On/Off and Brightness (if controller mounted inverter is used). On
CNC1 the pins are for momentary type buttons so it doesn’t matter that no buttons are attached.
INVERTER CONNECTION
There are potentially 3 issues to consider with inverter connection:
Power
Enable
Brightness
Please read the following sections for a guide to these issues.
Inverter Power: As per the table for CNB1 pin 1 is ground and pin 2 provides 12V/24V DC. This should be matched with the
inverter specification: see table.
CNB1
PIN DESCRIPTION
1 Ground
2 +12V/+24VDC
Remark: For higher power inverter, more current (for 12V/24V) can be taken from CNA1 pin 1.
Enable: This is a pin provided on some inverters for On/Off function and is used by this panel controller for VESA DPMS
compliance. If the inverter does not have an enable pin or the enable pin is not used then DPMS will not be operational. Pin 3
should be matched to the inverters specification for the ‘enable’ or ‘disable’ pin.
CNB1
PIN DESCRIPTION
3 Enable
Further, jumpers JB2 & JB3 should be set to match the inverters specification for the enable pin power and High or Low
setting: see table.
Ref
Purpose Note
JB2 Inverter enable voltage 1-2 H = 3.3VV, 2-3 H = 5V (Vcc), OPEN H = open collector
JB3 Inverter control 1-2 H = On, 2-3 L = On
Brightness: There are various methods for brightness control and it is important to consider the specifications for the inverter
to be used. Generally the situation is:
Brightness can control by using a resistor or VR (Variable Resistor).
Brightness controlled by adding a circuit such as PWM (Pulse Width Modulation).
No adjustment of brightness is possible.
CNB1 pins 4 & 5 are available for connecting to an inverter or circuit where VR control is supported.
CNB1
PIN DESCRIPTION
4 VR WIP
5 VR A
This can then be matched with function controls connected to CNC1 pins 4 & 3 or 5: see table.
CNC1
PIN DESCRIPTION
3 VR A
4 VR WIP
5 VR B
Design G e for making VF! circuitry: ninnai vim VR ck: ducripnnn 5v R1 = 4m nhln (an-board) RPOT o— mum; [Wtflneflnnl available at CNC1 pin 6). Figure 1 5 V 470 ohm a BVR_B “5’9 EVE?" ‘P RPOT o—h BVR_WIP 2.5 K 1.2 V 5 K 2.4 V 7.5 K 3.6 V 10 K 4.8 V I: Rpm = Rab + Rbc
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
29 of 60
Design Guideline for making VR circuitry :
CNB1 – Backlight inverter connector: JST B5B-XH-A (Matching type : XHP-5)
PIN SYMBOL DESCRIPTION
1 GND Ground
2 VBKL +12V/24VDC, backlight power supply
3 BLCTRL On/Off control (enable) – see JB2 & JB3
4 BVR_WIP Brightness VR - WIP
5 BVR_A Brightness VR A
CNC1 – Control switch, JST B12B-XH-A (Matching type : XHP-12)
PIN SYMBOL DESCRIPTION
1 PSWIN Power button A
2 SW_ON Power button B
3 BVR_A Backlight Brightness VR pin A
4 BVR_WIP Backlight Brightness R pin WIP
5 BVR_B Backlight Brightness VR pin B (470 ohm resistor to +5V Vcc)
6 GND Ground
7 MENU OSD menu
8 -/LEFT OSD -/Left
9 +/RIGHT OSD +/Right
10 SEL_DN OSD Select down
11 SEL_UP OSD Select up
12 NC No connection
The VR for brightness depends on the inverter. The main power load for On/Off is handled by a relay on the controller.
Example for circuit design :
Signal description / Notes :
1) R1 : 470ohm on board
2) RPOT is an external potentiometer (in-line dip
style) that can be plugged directly into CNC1 pins
3,4,5. RPOT must be supplied / installed by user.
3) BVR_B : Voltage tapped from “top” of
potentiometer, the node of R1 and RPOT.
4) BVR_WIP : Voltage tapped from wiper arm of
RPOT.
5) BVR_A : Voltage tapped from “bottom” of
RPOT.
Note : BVR_A voltage is left floating on the
controller board. To use this circuit, you need
to tie this point to a potential (usually GND,
available at CNC1 pin 6).
1.)Choose RPOT = 10K
2.) Tie BVR_A to GND
3.) Circuit analysis gives BVR_WIP as the
following (see Figure 1)
BVR_WIP = 5 x (Rbc/10.47)
where BVR_WIP is in Volts.
And Rbc is the resistance from the wiper arm
to bottom of pot in Kohms.
To evaluate, plug in different values of Rbc :
Rbc BVR_WIP
0 0 V
2.5 K 1.2 V
5 K 2.4 V
7.5 K
3.6 V
10 K 4.8 V
So this circuit could provide Brightness adjust
voltage ranging from 0V to 5V.
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
30 of 60
TROUBLESHOOTING
General
A general guide to troubleshooting a flat panel display system it is worth considering the system as separate elements, such
as:
Controller (jumpers, PC settings)
Panel (controller, cabling, connection, panel, PC settings)
Backlight (inverter, cabling, backlight tubes)
Cabling
Computer system (display settings, operating system)
Through step by step cross checking with instruction manuals and a process of elimination to isolate the problem it is usually
possible to clearly identify the problem area.
No image:
If the panel backlight is not working it may still be possible to just see some image on the display.
A lack of image is most likely to be caused by incorrect connection, lack of power, failure to provide a signal or incorrect
graphic card settings.
Image position:
If it is impossible to position the image correctly, i.e. the image adjustment controls will not move the image far enough, then
test using another graphics card. This situation can occur with a custom graphics card that is not close to standard timings or if
something is in the graphics line that may be affecting the signal such as a signal splitter (please note that normally a signal
splitter will not have any adverse effect).
Image appearance:
A faulty panel can have blank lines, failed sections, flickering or flashing display
Incorrect graphics card refresh rate, resolution or interlaced mode will probably cause the image to be the wrong size, to
scroll, flicker badly or possibly even no image.
Incorrect jumper settings on the controller may cause everything from total failure to incorrect image. CAUTION: Do not
set the panel power input incorrectly.
Sparkling on the display: faulty panel signal cable.
Found "Loading" message displayed on screen message at DVI input indicates the unstable DVI source
detected (especially connected to DVI splitter) causing flashing image.
No image found when non-matching video system signal input. For example, the condition of setting NTSC video system
(under OSD menu > Video System (SD)) and input PAL signal.
Backlight:
Items to check include: Power input, Controls, Inverter and Tubes generally in this order.
If half the screen is dimmer than the other half:
Check cabling for the inverter.
For a specific backlight tube check the AC pins orientation (CAUTION: Never reverse any DC power pins).
Also:
If adjusting brightness control has no effect the chances are that the VR rating or method of adjusting brightness is not
compatible or correctly connected to the inverter.
If system does not power down when there is a loss of signal
Continued failure:
If unit after unit keeps failing consider and investigate whether you are short circuiting the equipment or doing something else
seriously wrong.
Generally after common sense issues have been resolved we recommend step by step substitution of known working parts to
isolate the problem.
eve powe 40“ 70 o 50“
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
31 of 60
SPECIFICATIONS
Panel compatibility Compatible with 1920x1200, 1920x1080, 1680x1050, 1600x1200, 1440x900
1366x768, 1280x1024, 1024x768, 800x600 & 640x480 resolutions of TFT LCD
panels.
A specified BIOS and some factory adjustment may be required for individual
panel timings.
No. of colours Up to 3 x 8 bit providing 16.7 million colours.
Panel power DC 3.3V, 5V, 10V, 12V, 18V
Panel signal LVDS
Vertical refresh rate 60Hz at 1920x1200, 60Hz at 1920x1080, 60Hz at UXGA and up to 75Hz other
lower resolution
Display clock maximum 165MHz
ADC clock maximum 195 MHz
DVI differential input clock maximum 165MHz
Graphics formats Standard VESA VGA, SVGA, XGA, SXGA, WXGA, UXGA, WUXGA
Other special formats through specified BIOS and factory adjustment.
Graphics auto mode detect VGA, SVGA, XGA, SXGA, WXGA, UXGA & WUXGA interlaced and non-interlaced
Standard input at source (analog
RGB)
VGA analog (15 pin) standard with automatic detection of:
Digital Separate Sync;
Composite Sync
Sync On Green.
Video formats PAL, NTSC & SECAM
Video inputs VGA 1
DVI-I (DVI-D + VGA 2)
HD Component video
Composite video 1
Composite video 2
S-Video
S-Video 2
HD-SDI 1 (via HD-1000/2000)
HD-SDI 2 (via HD-2000)
Functions display On screen display (OSD) of functions
OSD menu functions Image controls:
Panel brightness/contrast, Saturation, Hue, Color temperature, Sharpness, Video
Scaling, PIP, OSD position, OSD timeout, Image orientation, Auto Source Seek,
etc.
OSD menu controls available Power On/Off
Backlight brightness
OSD Menu
OSD Select up
OSD Select down
Setting +
Setting -
Control interface Buttons, RS-232, Remote control
Settings memory Settings are stored in non volatile memory
PC Connectivity VGA / SVGA / XGA / SXGA / UXGA / WUXGA analog or digital
Controller dimensions 179mm x 120.4mm (7.” x 4.74”)
Power consumption 10w approx. (not including panel power consumption)
Power load maximum The controller has an overall 3Amp current limit.
Input voltage 12V/24VDC +/- 5%
Power protection Fuse fitted (Resettable)
DC Power handling Reverse power polarity protection is equipped on the board
Storage temperature limits -40
o
C to +70
o
C
Operating temperature limits 0
o
C to +60
o
C
Use of memory on board - 2pcs DDR3-1600 1Gbit which is a volatile memory for system processing and
frame buffer
- 1pc flash 32Mbit which is a non-volatile(NVRAM) memory for system program
- 2pcs EEPROM 2Kbit which is a non-volatile(NVRAM) memory for DDC
information.
- 1pc EEPROM 512Kbit which is a non-volatile(NVRAM) for system and user
settings
NOTES
Please note the following:
For specific panel setup a sample of an LCD may be required (this will be returned) and a copy of the full
technical specifications for the panel from the manufacturer.
Re-layout and custom development services are available.
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
32 of 60
APPENDIX I – SIGNAL SUPPORT MODE TABLE
VGA PORT :
Mode Resolution Clk [MHz]
Horizontal
freq [KHz]
Vertical
freq [Hz]
Sync Mode
V_60
640x480
60Hz
25.175 31.469 59.940 Digital Separate Sync
V_60
640x480
60Hz
25.175 31.469 59.940 Composite Sync
V_72
640x480
72Hz
31.500 37.861 72.809 Digital Separate Sync
V_72
640x480
72Hz
31.500 37.861 72.809 Sync On Green
V_72
640x480
72Hz
31.500 37.861 72.809 Composite Sync
V_75 640x480
75Hz
31.500 37.500 75.000 Digital Separate Sync
V_75
640x480
75Hz
31.500 37.500 75.000 Sync On Green
V_75
640x480
75Hz
31.500 37.500 75.000 Composite Sync
SV_56
800x600
56Hz
36.000 35.156 56.250 Digital Separate Sync
SV_56
800x600
56Hz
36.000 35.156 56.250 Composite Sync
SV_60
800x600
60Hz
40.000 37.879 60.317 Digital Separate Sync
SV_60
800x600
60Hz
40.000 37.879 60.317 Sync On Green
SV_60
800x600
60Hz
40.000 37.879 60.317 Composite Sync
SV_72
800x600
72Hz
50.000 48.077 72.188 Digital Separate Sync
SV_72
800x600
72Hz
50.000 48.077 72.188 Sync On Green
SV_72
800x600
72Hz
50.000 48.077 72.188 Composite Sync
SV_75 800x600
75Hz
49.500 46.875 75.000 Digital Separate Sync
SV_75 800x600
75Hz
49.500 46.875 75.000 Sync On Green
SV_75 800x600
75Hz
49.500 46.875 75.000 Composite Sync
X_60 1024x768
60Hz
65.000 48.363 60.004 Digital Separate Sync
X_60 1024x768
60Hz
65.000 48.363 60.004 Sync On Green
X_60 1024x768
60Hz
65.000 48.363 60.004 Composite Sync
X_70 1024x768
70Hz
75.000 56.476 70.069 Digital Separate Sync
X_70 1024x768
70Hz
75.000 56.476 70.069 Sync On Green
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
33 of 60
X_70 1024x768
70Hz
75.000 56.476 70.069 Composite Sync
X_75 1024x768
75Hz
78.750 60.023 75.029 Digital Separate Sync
X_75
1024x768
75Hz
78.750 60.023 75.029 Sync On Green
X_75
1024x768
75Hz
78.750 60.023 75.029 Composite Sync
SX_60 1280x1024
60Hz
108 63.81 60.020 Digital Separate Sync
SX_60 1280x1024
60Hz
108 63.81 60.020 Sync On Green
SX_60 1280x1024
60Hz
108 63.81 60.020 Composite Sync
SX_75 1280x1024
75Hz
135 79.976 75 Digital Separate Sync
SX_75 1280x1024
75Hz
135 79.976 75 Sync On Green
SX_75 1280x1024
75Hz
135 79.976 75 Composite Sync
WUX_60 1920x1080
60Hz
172.8 67.5 60 Digital Separate Sync
WUX_60 1920x1080
60Hz
172.8 67.5 60 Sync On Green
WUX_60 1920x1080
60Hz
172.8 67.5 60 Composite Sync
Remark :
The controller has been designed to take a very wide range of input signals however to optimize the PC’s graphics
performance we recommend choosing 60Hz vertical refresh rate. To support on higher refresh rate over 60Hz, the
LCD panel may not support.
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
34 of 60
DVI input port :
Mode Resolution Clk [MHz]
Horizontal
freq [KHz]
Vertical
freq [Hz]
V_60 640x480 60Hz 25.175 31.469 59.940
V_67 640x480 67Hz 31.5 37.5 67
V_75 640x480 75Hz 31.5 37.5 75
SV_56 800x600 56Hz 36 35.156 56
SV_60 800x600 60Hz 40.000 37.879 60.317
SV_72 800x600 72Hz 50 48.077 72
SV_75 800x600 75Hz 49.5 46.875 75
X_60 1024x768 60Hz 65.000 48.363 60.004
X_70 1024x768 70Hz 75 56.476 70
X_75 1024x768 75Hz 78.75 60.023 75
SX_60 1280x1024 60Hz 108 63.81 60.020
SX_75 1280x1024 75Hz 135 79.976 75
UX_60 1600x1200 60Hz 162 75.000 60
WUX_60 1920x1080 60Hz 172.8 67.5 60
1080p60 1920x1080p 60Hz 135 67.5 60
1080p59 1920x1080 59Hz 148.35 67.433 60
1080p50 1920x1080 50Hz 149 62.75 50
720p60 1280x720P 60Hz 74.25 45 60
576p50 720x576P 50Hz 26.9568 31.2 50
480p60 720x480P 60Hz 26.9568 31.4 60
HD-COMPONENT PORT :
COMPOSITE, S-VIDEO INPUT PORT :
System Resolution Horizontal freq
[KHz]
Vertical freq
[Hz]
NTSC 720x480i 15.7 60
NTSC 4.43
720x480i 15.7 60
PAL 720x576i 15.6 50
PAL M 720x576i 15.6 50
SECAM 720x576i 15.6 50
Mode
720p60
720p59.94
720p50
720p30
720p29.97
1080p30
1080p29.97
1080p25
1080p24
1080p23.98
1080i60
1080i59.94
1080i50
1080p60
1080p59.94
1080p50
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
35 of 60
Appendix II – RS-232 control protocols
RS-232 Serial control (Baud rate 2400/4800/9600/14400/19200/38400/57600/115200,
8 bits, 1 stop bit
and no parity
)
Please refer to Appendix VIII for the procedure how to select different baud rate to be used.
Physical connection :
Controller side Computer side
Connector interface : CN8 Connector interface : Serial port
Mating connector : JST XHP-6 Mating connector : DB9 Female
PIN# Description PIN# Description
4 RS-232 Tx Data 2 RS-232 Rx Data
5 Ground 3 RS-232 Tx Data
6 RS-232 Rx Data 5 Ground
Remark :
(1) : RS-232 connection cable, 600mm P/N 4260902-00 can be ordered separately for connection.
Software connection :
The OSD function can be controlled through sending the RS-232 protocol.
The RS-232 program can be custom-made to fit for application or it can be used the serial control program, like Accessport,
Telix or Serial Utility program developed by DigitalView. Please contact your local support for information.
5
4
6
3
1
78
9
Mating face of CN8 Mating face of RS-232 DB9 Male
5 4
63
1
Menu button 0x17 Menu button pressed Button equwa‘ent button Select-up button Oxtb Select-up button pressed Button equwa‘ent Rigntl+ button Oxtc RignI/+ button pressed Button equwa‘ent o", 55, Query, Source ‘1 o", 55, Query, Source ‘1 setect(0x98) o", 55, Query, Source ‘1 “7“ Query “7“ Query “7“ Query “7“ Query Frequency Oxab, Set Irequency = Graphtc mode H actwe size (in
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
36 of 60
1. Commands to implement switch mount control buttons
Function Command Description Remark
Menu button 0xf7 Menu button pressed Button equivalent
Select-down
button
0xfa Select-down button pressed Button equivalent
Select-up button 0xfb Select-up button pressed Button equivalent
Right/+ button
0xfc
Right/+ button pressed
Button equivalent
Left/- button 0xfd Left/- button pressed Button equivalent
2. Parameter setting - immediate, relative, reset and query
Function Command Description Acknowledge (if enabled)
Brightness control 0x81,
nn | “+” | “-” |
“r” | “R” |
“?”
“m”
“n”
“i” , ss, nn
o, ss,
Set brightness =
value/increment/decrement
Reset
Query Current Source
Maximum query *1
Minimum query *1
Set, Source, value *1
Query, Source *1
Brightness.
Range : “4””E”-“B””2”
Default : “8””0”
ss - reference by Input main
select(0x98)
Contrast control -
all channels
0x82, “a” | “A”,
nn | “+” | “-” |
“r” | “R” |
“?”
“m”
“n”
“i ” , ss, nn
o, ss,
Set all contrast =
value/increment/decrement
Reset
Query
Maximum query *1
Minimum query *1
Set, Source, value *1
Query, Source *1
Contrast
Range : “1””C”-“E””4”
Default : “8””0”
ss - reference by Input main
select(0x98)
Saturation control 0x83,
nn | “+” | “-” |
“r” | “R” |
“?”
“m”
“n”
“i” , ss, nn
“o”, ss,
Set color =
value/increment/decrement
Reset
Query
Maximum query *1
Minimum query *1
Set, Source, value *1
Query, Source *1
PAL/NTSC color (In video mode
only )
Range : “0””1”-“F””F”
Default : “8””0”
ss - reference by Input main
select(0x98)
Hue control 0x84,
nn | “+” | “-” |
“r” | “R” |
“?”
“m”
“n”
“i” , ss, nn
o, ss,
Set tint =
value/increment/decrement
Reset
Query
Maximum query *1
Minimum query *1
Set, Source, value *1
Query, Source *1
NTSC tint (In NTSC mode only)
Range : “0”"1”-“F””F”
Default : “8””0”
ss - reference by Input main
select(0x98)
Phase (tuning)
control
0x85,
nn | “+” | “-” |
?
Set dot clock phase =
value/increment/decrement
Query
Dot clock phase.
(In PC mode only)
Image H position 0x86,
nnnn | “+” | “-” |
?
Set img_hpos =
value/increment/decrement
Query
Image horizontal position.
(In PC mode only)
Image V position 0x87,
nnnn | “+” | “-” |
?
Set img_vpos =
value/increment/decrement
Query
Image vertical position.
(In PC mode only)
Sharpness 0x8a,
nn | “+” | “-” |
“r” | “R” |
?
Set sharpness =
value/increment/decrement
Reset
Query
Sharpness.
(Video Mode Source only)
Default : “0””C
Frequency 0x8b, Set frequency = Graphic mode H active size (in
”7,, Query “D"—2:1 “N" — Not suppon. “7” Query “7” Query it to the max available step. “8" — Chinese “0X46,0X31"DV| “0X46,0X31"DV| ”7,, Query “"-2 Picture by Picture (PBP)
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
37 of 60
nnnn | “+” | “-“ |
?
Value/increment/decrement
Query
pixels)
Scaling Mode 0x8c,
“0” | “1” | “2” | “3” |
“9” | “A” |
“B” | “C” | “D” |
“r” | “R” |
“?”
Set graphic image scaling mode
=
value
Reset
Query
Image expansion on/off.
“0” – 1:1
“1” – fill screen
“2” – fill to aspect ratio
“9” – 4:3
“A” – 16:9
“B” – 16:10
“C” – 2.35:1
D 2:1
Set display
orientation
(Effective on
V1.26.00.00 or later
firmware revision)
0x8e,
n |
“r” | “R” |
“?”
Set display orientation =
value/increment/decrement
Reset
Query
“0” – Normal.
“1” – Vertical Flip.
“2” – Horizontal Flip.
“3” – Rotate.
N Not support.
OSD H position 0x90,
nnn | “+” | “-” |
“r” | “R” |
?
Set osd_hpos =
value/increment/decrement
Reset
Query
OSD horizontal position.
OSD V position 0x91,
nnn | “+” | “-” |
“r” | “R” |
?
Set osd_vpos =
value/increment/decrement
Reset
Query
OSD vertical position.
OSD menu
timeout
0x93,
nn | “+” | “-” |
“r” | “R” |
“?”
Select menu timeout =
value/increment/decrement
Reset
Query
OSD menu timeout value.
“0””0” – Continuous.
value – Round up to nearest
available step.
if value > max available step, set
it to the max available step.
Select OSD
language
0x95,
n |
“r” | “R” |
“?”
Select language =
English, Chinese,…
Reset
Query
“0” – English.
“2” - French
“3” – Spanish
“6” - German
8 Chinese
Input main select 0x98,
nn | “+” | “-” |
“r” | “R” |
“?”
Select input main =
PC or VIDEO or next available
Reset
Query
Main selected.
“0x41,0x31” VGA 1
“0x41,0x32” VGA 2
“0x42,0x31” Composite 1
“0x42,0x32” Composite 2
“0x43,0x31” S-video 1
“0x43,0x32” S-video 2
“0x44,0x31” HD/SD Component
“0x45,0x31” HDSDI 1
++
“0x45,0x32” HDSDI 2
++
0x46,0x31 DVI
Auto Source Seek 0x99,
nn ,
“0” | “1” |
“?” |
”o”
Set Auto source enable = *1
Source
Disable/ Enable
Query
Valid Source query
“nn” =
“0x41,0x31” VGA 1
“0x41,0x32” VGA 2
“0x42,0x31” Composite 1
“0x42,0x32” Composite 2
“0x43,0x31” S-video 1
“0x43,0x32” S-video 2
“0x44,0x31” HD/SD Component
“0x45,0x31” HDSDI 1
++
“0x45,0x32” HDSDI 2
++
0x46,0x31 DVI
Source Layout 0x9a,
n |
“r” | “R” |
?
Select source layout =
Single, PIP, PBP, PBPT
Reset,
Query
Query:
“0”- Single
“1”- Picture in Picture (PIP)
2- Picture by Picture (PBP)
“F" — Turn ON PIP Window ‘ “C" — 2.6 Query "K" - PIP ON/OFF "K" - PIP ON/OFF Query Query Query Query “1"""9 : Srze by Size
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
38 of 60
“3”- Picture by Picture Tall
(PBPT)
F Turn ON PIP Window
***
Gamma value
select
(Effective on
V1.27.00.00 or later
firmware revision)
0x9d,
n |
“r” | “R”
“?”
Select GAMMA value =
Value
Reset
Query
GAMMA value:
“5” – 1.8,
“6” – 1.9,
“7” – 2.0,
“8” – 2.1,
“2” – 2.2,
“9” – 2.3,
“A” – 2.4,
“B” – 2.5,
C 2.6
Auto power off 0x9f,
“0” | “1” |
“r” | “R” |
?
Set power down option =
On/Off
Reset
Query
“0” – Off.
“1” – On.
Hotkey 1
0xa0, “1”,
n |
“r” | “R” |
“?”
Set Hotkey 1=
Value
Reset
Query
“2” – brightness.(Default)
“3” – contrast.
“4” – colour.
“5” – input source.
“7” – zoom
“8” – freeze
"9" - PIP
“B” – No function
"D" - PIP Swap
“E” – Aspect Ratio
“G” – Hue
“H” – Backlight
“I” – Auto Picture Setup
"K" - PIP ON/OFF
Hotkey 2
0xa0, “2”,
n |
“r” | “R” |
“?”
Set Hotkey 2 =
value
Reset
Query
“2” – brightness.
“3” – contrast. (Default)
“4” – colour.
“5” – input source.
“7” – zoom
“8” – freeze
"9" - PIP
“B” – No function
"D" - PIP Swap
“E” – Aspect Ratio
“G” – Hue
“H” – Backlight
“I” – Auto Picture Setup
"K" - PIP ON/OFF
Runtime counter 0xa1,
nnnnn |
“r” | “R” |
?
runtime counter value =
nnnnn (* 0.5 hour)
Reset
Query
Runtime = nnnnn.
PIP H position 0xa4,
nnn | “+” | “-” |
“r” | “R” |
?
Set PIP_hpos =
value/increment/decrement
Reset
Query
PIP window horizontal position.
"0""0""0" ~"0""6""4"
Default : "0""5""5"
PIP V position 0xa5,
nnn | “+” | “-” |
“r” | “R” |
?
Set PIP_vpos =
value/increment/decrement
Reset
Query
PIP window vertical position.
"0""0""0" ~"0""6""4"
Default : "0""1""4"
PIP window size
select
0xa6,
nn |
“r” | “R” |
?
Select PIP window size =
PIP window size value
Reset
Query
Main selected.
PIP off if “nn” = “0””0”
“0””0” ~ “1””2”
19 : Size by Size
“0X46,0X31"DV| “7“ Query resolution. resolution. “4" - User “0", 55, c Query, Source ‘1 se‘ectmeB) Query, Source ‘1 se‘ectmeB). “7“ Derauh : “E""3"1or 8000K Query
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
39 of 60
“1””A” : Size by Size Tall
Default : "0""0"
PIP source select 0xa7,
n |
“r” | “R” |
“?”
Select input main =
Video source value
Reset
Query
Main selected.
“0x41,0x31” VGA 1
“0x41,0x32” VGA 2
“0x42,0x31” Composite 1
“0x42,0x32” Composite 2
“0x43,0x31” S-video 1
“0x43,0x32” S-video 2
“0x44,0x31” HD/SD Component
“0x45,0x31” HDSDI 1
++
“0x45,0x32” HDSDI 2
++
0x46,0x31 DVI
Zoom level
0xa8,
nnnn | “+” | “-” |
“r” | “R” |
?
Set Zoom level =
value/increment/decrement
Reset
Query
Zoom level.
Zoom H position 0xa9,
nnnn | “+” | “-” |
“r” | “R” |
“?”
Set Zoom_hpos =
value/increment/decrement
Reset
Query
Zoom window horizontal position.
Default : 0x30 0x30 0x30 0x30
The min and max values will
change depends on input
resolution.
Zoom V position
0xaa,
nnnn | “+” | “-” |
“r” | “R” |
“?”
Set Zoom_vpos =
value/increment/decrement
Reset
Query
Zoom window vertical position.
Default : 0x30 0x30 0x30 0x30
The min and max values will
change depends on input
resolution.
Colour
temperature select
0xb3,
n |
“r” | “R” |
“?”
Select colour temperature =
value
Reset
Query
Main selected.
“0” – 9300K.
“1” – 8000K.(Default)
“2” – 6500K.
“3” – 5000K
4 - User
Red level for
selected colour
temperature
0xb4,
nn | “+” | “-” |
“r” | “R” |
“?”
“m”
“n”
“i” , ss, c, nn
o, ss, c
Set the level of the red channel
for the selected colour temp. =
value/increment/decrement
Reset
Query
Maximum query *1
Minimum query *1
Set, Source, Temperature
Group, value *1
Query, Source *1
Red level for selected colour
temperature.
Range : “9””C”-“F””F”
Default : “E””3” for 8000K
c – reference by Color
Temperature
ss - reference by Input main
select(0x98)
Green level for
selected colour
temperature
0xb5,
nn | “+” | “-” |
“r” | “R” |
“?”
“m”
“n”
“i” , ss, c, nn
“o”, ss, c
Set the level of the green
channel for the selected colour
temp. =
value/increment/decrement
Reset
Query
Maximum query *1
Minimum query *1
Set, Source, Temperature
Group, value *1
Query, Source *1
Green level for selected colour
temperature
Range : “9””C”-“F””F”
Default : “E””3” for 8000K
c – reference by Color
Temperature
ss - reference by Input main
select(0x98).
Blue level for
selected colour
temperature
0xb6,
nn | “+” | “-” |
“r” | “R” |
?
Set the level of the blue channel
for the selected colour temp. =
value/increment/decrement
Reset
Query
Blue level for selected colour
temperature.
Range : “9””C”-“F””F”
Default : E3 for 8000K
“o”, 55, c Query, Source ‘1 se‘ectmeB). reso‘ulion enquiry 3 digit hex number reso‘ulion enquiry digit nex number enquiry number or Progressive(p)1eedback. enquiry “1"— OSD turned on seconds. “1"— successiu‘. “7" — Not Support 440HZ : “0"”0" ~ “1D “R“ \ “r” “7"— Backhght On/Oii Query
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
40 of 60
“m”
“n”
“i” , ss, c, nn
o, ss, c
Maximum query *1
Minimum query *1
Set, Source, Temperature
Group, value *1
Query, Source *1
c – reference by Color
Temperature
ss - reference by Input main
select(0x98).
Graphic horizontal
resolution enquiry
0xb7 Horizontal resolution (in pixels) in
3 digit hex number
“nnn” = horizontal resolution
Graphic vertical
resolution enquiry
0xb8 Vertical resolution (in lines) in 3
digit hex number
“nnn” = vertical resolution
Graphic horizontal
sync frequency
enquiry
0xb9 Horizontal sync frequency (in
units of 100Hz) in 3 digit hex
number
“nnn” = horizontal frequency
Graphic vertical
sync frequency
enquiry
0xba Vertical sync frequency (in units
of Hz) in 3 digit hex number and
1 char
“nnnn” = vertical frequency
nnn = 3 digit hex
c= “i” or “p”
interlace or Progressive
0xba added the interlace(i)
or
Progressive(p) feedback.
OSD status
enquiry
0xbb Status of OSD “0” – OSD turned off
1 OSD turned on
Display Video
Source Select
0xbc,
“?” |
“0” |
“1”
Display Video source select
Query
Name of video source not
displayed.
After switching to a new video
source, the name of the video
source is displayed for 5
seconds.
“0” – Disabled.
“1” – Enabled.
OSD turn off 0xbd Turn off the OSD. “0” – fail.
1 successful.
Query External
Memory
0xcb, “2” Check External Menory 24c256 “0” – Not Installed
“1” – Installed
? Not Support
Query Revision
Number
0xcb, “3” Read Revision Number “nn” = Revision number
Backlight control 0xe0,
nn | “+” | “-” |
"="|
“R” | “r” |
“?”
Set Backlight =
value/increment/decrement
Display OSD indicator
Reset
Query
Backlight.
Range:
D/A : “0””0” ~ “5””2”
100Hz : “0””0” ~ “8””3”
120Hz : “0””0” ~ “6”"D”
140Hz : “0””0” ~ “5””D”
160Hz : “0””0” ~ “5””2”
180Hz : “0””0” ~ “4””8”
200Hz : “0””0” ~ “4””2”
220Hz : “0””0” ~ “3””B”
240Hz : “0””0” ~ “3””6”
260Hz : “0””0” ~ “3””2”
280Hz : “0””0” ~ “2””E”
300Hz : “0””0” ~ “2””B”
320Hz : “0””0” ~ “2””8”
340Hz : “0””0” ~ “2””6”
360Hz : “0””0” ~ “2””4”
380Hz : “0””0” ~ “2””2”
400Hz : “0””0” ~ “2””0”
420Hz : “0””0” ~ “1””E”
440Hz : 00 ~ 1D
Backlight On/Off 0xe1,
“0” | “1” |
R | r
Backlight Off / Backlight On
/Status
“0” – Backlight Off
“1” – Backlight On.(Default)
? Backlight On/Off Query
Query 440HZ:“1""B“,"8" Query “o", 55, c Query, Source ‘1 se‘ectmeB) Query, Source ‘1 se‘ectmeB) temperature nn \ “+" | “-“ \ temp. =
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
41 of 60
?
Color
Monochrome
mode selection
(Output Channel
Select)
(Effective on
V1.26.00.00 or later
firmware revision)
0xe2
“0” | “1” | “2” | “3” |
| “4” | “5” | “6” |
“R” | “r”|
”?”
Off/
Blue Only/
Red Only/
Green Only/
Blue Mono/
Red Mono/
Green Mono/
“0” – Off
“1” – Blue Only
“2” – Red Only
“3” – Green Only
“4” – Blue Mono
“5” – Red Mono
“6” – Green Mono
Backlight D/A /
PWM
0xe5
“0” | “1” |
“R” | “r”
”?”
Set : PWM or D/A
Reset
Query
“0” – PWM
“1” – D/A (Default)
Backlight PWM
Frequency
0xe6,
nnn | “+” | “-” |
“R” | “r” |
“?”
Set Backlight PWM Frequency =
value/increment/decrement
Reset
Query
+/- 20Hz
Value
100Hz : “0”,”6”,”4”
120Hz : “0”,”7”,”8”
140Hz : “0”,”8”,”C”
160Hz : “0”,”A”,”0” (Default)
180Hz : “0”,”B”,”4”’
200Hz : “0”,”C”,”8”
220Hz : “0”,”D”,”C”
240Hz : “0”,”F”,”0”
260Hz : “1”,”0”,”4”
280Hz : “1”,”1”,”8”
300Hz : “1”,”2”,”C”
320Hz : “1”,”4”,”0”
340Hz : “1”,”5”,”4”
360Hz : “1”,”6”,”8”
380Hz : “1”,”7”,”C”
400Hz : “1”,”9”,”0”
420Hz : “1”,”A”,”4”
440Hz : 1,B,8
Backlight Invert 0xe7
“0” | “1” |
“R” | “r”
”?”
Set On or Off
Reset
Query
“0” – Off
“1” – On
Red Offset for
selected colour
temperature
0xe8,
nn | “+” | “-” |
“r” | “R” |
“?”
“m”
“n”
“i” , ss, c, nn
o, ss, c
Set the Offset of the red channel
for the selected colour temp. =
value/increment/decrement
Reset
Query
Maximum query *1
Minimum query *1
Set, Source, Temperature
Group, value *1
Query, Source *1
Red Offset for selected colour
temperature.
Range : “8””0”-“7””F”
Default : "0""0"
c – reference by Color
Temperature
ss - reference by Input main
select(0x98)
Green Offset for
selected colour
temperature
0xe9,
nn | “+” | “-” |
“r” | “R” |
“?”
“m”
“n”
“i” , ss, c, nn
“o”, ss, c
Set the Offset of the green
channel for the selected colour
temp. =
value/increment/decrement
Reset
Query
Maximum query *1
Minimum query *1
Set, Source, Temperature
Group, value *1
Query, Source
*1
Green Offset for selected colour
temperature.
Range : “8””0”-“7””F”
Default : "0""0"
c – reference by Color
Temperature
ss - reference by Input main
select(0x98)
Blue Offset for
selected colour
temperature
0xea,
nn | + | - |
Set the Offset of the blue
channel for the selected colour
temp. =
Blue Offset for selected colour
temperature.
Query, Source ‘1 se‘ectmeB) “0"1": 93.75% “0“0" = 100%. “S“ “5“ Light Detector Value Query Value Query 0x00~0xFF “7“ Query 440HZ : "0”"0" ~ "3”"1" “7“ Query “3" Prxe‘ Shit! Amr Image “0xee”, “0x60"
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
42 of 60
“r” | “R” |
“?”
“m”
“n”
“i” , ss, c, nn
“o”, ss, c
value/increment/decrement
Reset
Query
Maximum query *1
Minimum query *1
Set, Source, Temperature
Group, value *1
Query, Source *1
Range : “8””0”-“7””F”
Default : "0""0"
c – reference by Color
Temperature
ss - reference by Input main
select(0x98)
PIP Window Blend
Level
0xed,
nn | “+” | “-” |
“R” | “r” |
“?”
Select PIP Transparency Level
PIP Transparency value
Reset
Query
PIP Transparency
“0”F” = 6.25% “0”E” = 12.5%
“0”D” = 18.75% “0”C” = 25%
“0”B” = 31.25% “0”A” = 37.5%
“0”9” = 43.75% “0”8” = 50%
“0”7” = 56.25% “0”6” = 62.5%
“0”5” = 68.75% “0”4” = 75%
“0”3” = 81.25% “0”2” = 87.5%
01 = 93.75% 00 = 100%.
Light Detector
“0xee”, “0x4A”
“0” | “1” |
“R” | “r”
”?”
S | s
Light Detector Off / Light
Detector On
Light Detector On/Off Query
Light Detector Value Query
“0” –Light Detector Off (Default)
“1” –Light Detector On.
“?” – Light Detector On/Off
Query “S”|”s” –Light Detector
Value Query 0x00~0xFF
Access
Programming
Mode
"0xee", "0x59"
"0" | "1"
"2"
"?"
Cancel Access / Set Access
Run Smart ISP programming
Query
"0" - Cancel Access
"1' - Set next start up to access
the programming mode.
Minimum
Backlight Value
0xee, "0x5C"
nn| "+" | "-"|
"R" | "r" |
"?"
Set Minimum Backlight value =
value / increment / decrement
Reset
Query
Minimum Backlight value/
Range :
D/A : "0""0" ~ "3""2"
100Hz : "0""0" ~ "3""2"
120Hz : "0""0" ~ "3""2"
140Hz : "0""0" ~ "3""2"
160Hz : "0""0" ~ "3""2"
180Hz : "0""0" ~ "3""2"
200Hz : "0""0" ~ "3""2"
220Hz : "0""0" ~ "3""2"
240Hz : "0""0" ~ "3""2"
260Hz : "0""0" ~ "3""2"
280Hz : "0""0" ~ "3""2"
300Hz : "0""0" ~ "3""2"
320Hz : "0""0" ~ "3""2"
340Hz : "0""0" ~ "3""0"
360Hz : "0""0" ~ "3""0"
380Hz : "0""0" ~ "3""0"
400Hz : "0""0" ~ "3""1"
420Hz : "0""0" ~ "3""1"
440Hz : "0""0" ~ "3""1"
OSD Switch
Mount Lock
"0xee", "0x62"
"0" | "1"
"?"
Unlock / Lock
Query
"0" - Unlock
"1" - Lock
Anti image
retention
“0xee”, “0x6C”
“E” ,
“1” | “0”
Anti image retention
On / Off
Anti image
retention Method
“0xee”, “0x6C”
“M” ,
“0” |
“1”|
“2”|
3
Run Anti image retention Method
Horizontal Pan
Vertical Pan
Flash
Pixel Shift
Anti image 0xee, 0x6C
acknowledge acknowledge. “1"— acknowledge enabled. vmode. “1"— successlul. availability available. “1"— available. ol the RGB amplilier. “1"— successlul. ”7.. query “F","1 “ DVI YY= Version Number
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
43 of 60
retention Pixel
Shift Manual
“P” ,
“H” | “V”|
“nn” | “+” | “-” |
“R” | “r” |
“?”
Anti image retention Pixel Shift
Manual
Horizontal / Vertical Shift
value/increment/decrement
Reset
Query
Remark :
++ - Support when HD-1000/-2000/-3000S connected.
3. Other control
Function Command Description Acknowledge (if enabled)
Select RS-232
acknowledge
0xc1, “0” | “1”
Disable/enable command
acknowledge.
“0” – acknowledge disabled.
1
acknowledge enabled.
Auto-setup 0xc3 Start auto-setup of current
vmode.
“0” – fail.
1 successful.
Command
availability
0xc4, n Check whether a command is
available.
“0” – not available.
1 available.
Auto-calibration 0xc5 Start auto-calibration of gain
of the RGB amplifier.
“0” – fail.
1 successful.
Freeze frame
0xc6, “0” | “1”
"="|
Unfreeze / freeze frame
Display OSD indicator
“0” – unfreeze.
“1” – freeze.
Soft Power On/Off 0xc8,
“0” | “1” |
?
Soft power
off/on
query
"0" - Soft power off
"1" - Soft power on
Query video input
status
0xc9 Query the status of the
primary & pip status
“nn,nn” = input status
“nn,xx” digit = primary status:
“0”,”0” : invalid
“A”,”1” VGA 1
“A”,”2” VGA 2
“B”,”1” Composite 1
“B”,”2” Composite 2
“C”,”1” S-video 1
“C”,”2” S-video 2
“D”,”1” Component 1 (via CNV2)
“E”,”1” HDSDI 1
++
“E”,”2” HDSDI 2
++
“F”,”1” DVI
“xx,nn”= PIP input status:
“0”,”0” : invalid
“A”,”1” VGA 1
“A”,”2” VGA 2
“B”,”1” Composite 1
“B”,”2” Composite 2
“C”,”1” S-video 1
“C”,”2” S-video 2
“D”,”1” Component 1 (via CNV2)
“E”,”1” HDSDI 1
++
“E”,”2” HDSDI 2
++
F,1 DVI
Query BIOS
version
0xcb, “0” Read BIOS version BIOS version “VV.YY.ZZ”
VV = V0 or E0,
V0 = Release version
E0 = Engineering Sample
YY= Version Number
22: Customer Number number SVH-1920V2: “41752" Deiauits deiault vaiue temp) deiault deiault vaiue “E" — Checksum Error "5" - 1600x900 Function Command Description Acknowledge (if enabled)
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
44 of 60
ZZ= Customer Number
Query PCBA
number
0xcb, “1” Read PCBA number “nnnnn” = PCBA number
SV
H
-
1920v2
= 41
752
Reset to Factory
Defaults
0xce Reset all parameters to
default value
“1” – successful.
Reset to Factory
Defaults with (color
temp)
0xcf Reset all parameters for all
video modes to default value
“1” - successful.
Saved Calibrated
default
0xd7 Saving all parameters to user
default value
“1” - successful.
Load Calibrated
default
0xd8 Loading all parameters to
user default value
“1” - successful.
“0” - not successful
E Checksum Error
Wide Screen
Mode Selection
0xd9,
“n""n”
“r” | “R”
“?”
Wide Screen Mode
Reset
Query
“n,n” = input status
“n,x” digit = Group 1 mode select:
"0" – 1024x768 (Default)
“1” – 1280x768
“2” – 1366x768
"3" - 1360x768
“x,n”= :Group 2 mode select
"4" - 1440x900 (Default)
"5" - 1600x900
The following commands for sending texts by using RS-232 command.
Function
Command
Description
Acknowledge (if enabled)
Send Line 0xF0,
|”S” |”LL”|”TEXT”|
“0x0A”
Return “1”
“S” = “0x53 or 0x73”
Send command
-------------------------------------------
-
“LL” = “0x30,0x31~0x30,0x34”
Line number (Rang 0~4 lines)
-------------------------------------------
-
“Text”= ASCII code,
“0x20~0x7E”
Character( Rang 0~34 )
-------------------------------------------
-
0x0A = End of line
“S” – Send Command
“LL” – Line Number
“Text” – Character
“0x0A” – End of Line
“1” - successful.
e.g Display “Send Text” message on screen:
RS232 Code:“0xF0 0x53 0x30 0x31 0x53 0x65 0x6E 0x64 0x20 0x54 0x65 0x78 0x74 0x0A”
Return Code: “0xF0 0x53 0x30 0x31 0x53 0x65 0x6E 0x64 0x20 0x54 0x65 0x78 0x74 0x0A 0x31”
Clear Line 0xF0,
|”C” |”LL”|
Return “nn”
“C” = “0x43 or 0x63”
Clear command
-------------------------------------------
-
“LL” = “0x30,0x31~0x30,0x34”
Line number (Rang 0~4 lines)
“C” – Clear command
“LL” – Line Number
“nn” – Return Line number
e.g Clear Line 1
RS232 Code: “0xF0 0x43 0x30 0x31
Return Code: “0xF0 0x43 0x30 0x31 0x30 0x31”
“nn” — Return Positron number “nn” — Return Positron number Return n “N" = “0X30~0x31" “0" Turn 0" Text Overlay
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
45 of 60
Text Window
Horizontal Position
0xF0,
|”H” |”ss”|
Return “nn”
“H” = “0x48 or 0x68”
------------------------------------------
--“nn” = “0x30,0x30~0x46,0x46”
“H” – Horizontal Position
command
“ss” – Set Horizontal Position
number
nn Return Position number
e.g Set Text Window Horizontal Position
RS232 Code: “0xF0 0x48 0x30 0x31
Return Code: “0xF0 0x48 0x30 0x31 0x30 0x31”
Text Window
Vertical Position
0xF0,
|”V” |”ss”|
Return “nn”
“V” = “0x56 or 0x76”
------------------------------------------
--“nn” = “0x30,0x30~0x46,0x46”
“V” – Vertical Position command
“ss” – Set Vertical Position
number
nn Return Position number
e.g Set Text Window Vertical Position
RS232 Code: “0xF0 0x56 0x30 0x31
Return Code: “0xF0 0x56 0x30 0x31 0x30 0x31”
Left offset 0xF0,
|”O” |”SSS”|
Return “nnn”
“O” = “0x4F or 0x6F”
Set Left Offset command
-------------------------------------------
-
“SSS” = “0x30,0x30,0x30~
0x33,0x46,0x46”
Offset Value (Rang 000~3ff)
“O” – Left Offset Command
“SSS”- Offset Value (pixels)
“nnn”- Return Value(pixels)
e.g Set Left Offset = 100 pixels ( 0x64 (HEX))
RS232 Code: “0xF0 0x4F 0x30 0x36 0x34”
Return Code: “0xF0 0x4F 0x30 0x36 0x34 0x30 0x36 0x34”
Text Window
Horizontal Size
0xF0,
|”X” |”SSS”|
Return “nnn”
“X” = “0x58”
Set Horizontal Size command
-------------------------------------------
-
“SSS” = “0x31,0x45,0x30~
0x37,0x38,0x30”
Horizontal Size Value (Rang
000~3ff)
“X” –Horizontal Size
“SSS”- Size Value (pixels)
“nnn”- Return Value(pixels)
e.g Set Text Window Horizontal Size = 640 pixels ( 0x280 (HEX))
RS232 Code: “0xF0 0x58 0x32 0x38 0x30”
Return Code: “0xF0 0x58 0x32 0x38 0x30 0x32 0x38 0x30”
Background
Transparency
0xF0,
|”B”|”N”|
Return “n”
“B” = “0x42 or 0x62”
Set Transparency command
-------------------------------------------
“N” = “0x30~0x46”
Transparency Value
(Rang 00~0F)
“B” - Transparency command
“N” – Transparency Value
“n”- Return Value
0x00 =opaque
Set background Transparency value is 8
RS232 Code: “0xF0 0x42 0x38”
Return Code: “0xF0 0x42 0x38 0x38”
Text Overlay
Background
On or Off
0xF0,
|”Q”|
“N”
Return n
“Q” = “0x51 or 0x71”
Set Background Enable or
Disable ----------------------
N = 0x30~0x31
“B” - command
“1” Turn On Text Overlay
Background
0 Turn Off Text Overlay
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
46 of 60
Background
“n”- Return Value
Set background Transparency value is 8
RS232 Code: “0xF0 0x51 0x31”
Return Code: “0xF0 0x51 0x31 0x31”
Please set the "Background Transparency” and "Left offset" commands before the "Send Line"
command.
0x30 0 0x41 A 0x61 3 0x23 0X31 1 0X42 B 0X62 b 0X2D 0x32 2 0x43 C 0x63 (1 OxaF 0X33 3 0X44 D 0X64 (1 0x34 4 0x45 E 0x65 e 0X35 5 0X46 F 0X66 f 0x36 6 0x47 G 0x67 9 0X37 7 0X48 H 0X68 h 0X38 8 0X49 | 0X69 i 0X39 9 0X4A J OXGA j 0x43 K 0x63 k 0x40 L 0x60 | 0X4D M OXGD m 0X4E N ()er n 0X4F O OXGF a 0x50 P 0x70 p 0x51 0 0x71 q 0x52 R 0x72 r 0x53 8 0x73 5 0X54 T 0x74 1 0x55 U 0x75 u 0x56 V 0x76 v 0x57 W 0x77 w 0x58 X 0x78 x 0x59 Y 0x79 y OXSA Z 0X7A z
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
47 of 60
The RS-232 command strings sent in one time can support up to 380 bytes via CN8 port
The RS-232 command string sent in one time can support up to 50 bytes via CN1 or J1 port.
n = 1-byte ascii-coded hex number, e.g., parameter value of 0x1 is represented by “1” (0x31).
mn or nn = 2-byte ascii-coded hex number, e.g., parameter value of 0x1e is represented by “1”, “e” | “E”
(0x31, 0x6e|0x4e).
Please refer to the ASCII to Hex convert table below.
Hex to ASCII conversion table
Hex ASCII Hex ASCII Hex ASCII Hex ASCII
0x30 0 0x41 A 0x61 a 0x2B +
0x31 1 0x42 B 0x62 b 0x2D -
0x32 2 0x43 C 0x63 c 0x3F ?
0x33 3 0x44 D 0x64 d
0x34 4 0x45 E 0x65 e
0x35 5 0x46 F 0x66 f
0x36 6 0x47 G 0x67 g
0x37 7 0x48 H 0x68 h
0x38 8 0x49 I 0x69 i
0x39 9 0x4A J 0x6A j
0x4B K 0x6B k
0x4C L 0x6C l
0x4D M 0x6D m
0x4E N 0x6E n
0x4F O 0x6F o
0x50 P 0x70 p
0x51 Q 0x71 q
0x52
R
0x72
r
0x53 S 0x73 s
0x54 T 0x74 t
0x55 U 0x75 u
0x56 V 0x76 v
0x57 W 0x77 w
0x58 X 0x78 x
0x59 Y 0x79 y
0x5A Z 0x7A z
1 cycle CKAIIH CK' AlN— \ RAINDI MINU— RAIN“ MINI- MIND EMMA KAIHM MINE- CKBINi CKBIM “1N0! REIND- RBINH RBlNl— RBINH REINZ’ 11mm REIMB-
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
48 of 60
Appendix III – Mapping definition
Definition of Mapping A :
CHIN? CKAIN’ ”mm RAlRfl~ BAml+ KAINF RAINZ! “WP RAIN3+ nm& mam, UmlW HUM RBINfl* HEINH mum Xfllflli RBINZ- RHINS! REIMB- 1 cycle
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
49 of 60
Definition of Mapping B :
DMII Om Pair Bil V B"! BI“ BR! "2 In 1 Silo DBI7 6] l TXDEC DEIJJ] ITXDED GED RB REA REG REE RE1 RED DB[5:4] l TXDEI BE! BED GE5 GE! GE! GE 6E1 DEIQ Bl JTXDE2 EN V5 HS EE5 BEA 5E3 §E2 06(3 2] l TXDEJ "MW 6E7 BEG GE? GEE RET REE 0515 4] / 1x064 mm ‘ 5:9 3:5 559 655 RES its um 51 r txoou 600 R05 R04 R03 R02 R01 R00 DG‘? 6] ”WOO! BO? Bu) 605 604 603 GCXZ 60! mus 1] i'rxnoq’ EN vs HS 805 and 503 302' DRV 6| ITxum nan/pg so? we 607 606 R07 R06 mus a] I1XDOA m 508 BOB 609 Goa RD: R'oo DRIBJI I TXDOC TKDOC /—\—/—- Txood 1x003 TxDoz W001 TxDoa TXDEC IXDEA vxoen 1x062 1XDE1 TXDEfl E a s- v --EEEEEE “1
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
50 of 60
Definition of VESA :
Womp‘llpfll IIC III II“ an: III: M1 [Ill Damn I 1x050 DB[3 21 I must) 3E4 R59 use RE? REG REE REA DB[5 A] iTXDEI 5E5 BEA SE9 6E8 GE! GES 6E5 DEB E] ITXDE2 EN VS HS EEQ BER BE, EES nqamima field/pig as: as: as: :52 ass as) DGIE A] l 7105‘ law BEN BED GEI GEO RE! RED 1:611:61 1 TXDOD 604 R09 R05 R07 R06 R05 R04 DG[9:B]/ TXDOI 305 BOA (30‘) 608 507 606 ‘ 605 09152] I rxooz EN vs HS 509 BOB 507 j me warm] ITXDOI! nan/pm BOG 302 603 (302 RES 1 R02 DRE? B1 I TXDO-l low ‘ BOI 800 901 600 R0! ‘ R00 om 2117x000 ' 1 TXDOC I \ I “W ”003 "W mm mm” [mm mm am mo . vs I6 509 6 mm n-mamaam m I-«Eanm m -uannma- ass -nmum ass rxDEa TXDEI TxDEU
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
51 of 60
Definition of JEIDA :
lay must http://www.d\aitalview.com/support/down\oads/TestPattern 1280.BMP Warning
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
52 of 60
Appendix IV – Auto Color Gain
The Auto Color Gain function is supported in the VGA mode only and is designed to calibrate
the controller to the incoming video signal. In order to calibrate correctly, the display must be
displaying an image containing both black and white data (see illustration below) when the function is
used. The internal processor of the video controller chip will then execute a process to adjust the
relative values of the RGB signals to achieve the best performance. The parameters of the corrected
RGB values are then stored in the controller and are unaffected by the Reset Factory Defaults
function.
The reference pattern can be downloaded at :
http://www.digitalview.com/support/downloads/TestPattern_1280.BMP
This reference pattern is for 1280x1024 resolution and it needs to set your VGA input source to
1280x1024 resolution before performing the Auto Color Gain function. The position of the black
vertical bar in the pattern at the right side is important. It will affect the calibration result if you are
setting the VGA input to other resolution.
Warning - If the Auto Color Gain is executed without an appropriate image being displayed, then the
process will set incorrect values and the display colors will be distorted. If this occurs, then it can
either be corrected by performing the process correctly or if this is not possible then the Reset Color
Gain function can be used. This function will reset the stored RGB values to a set of approximate
values.
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
53 of 60
Appendix V – DV remote control unit work for SVH-1920v2
BUTTON FUNCTION
POWER BUTTON Soft power ON/OFF button.
SEL UP ( ) / SEL DN ( )
Use this button to direct control the hotkey function. Press the “SEL UP” button to
increase the pre-set hotkey parameter value and the “SEL DN” button to decrease the
pre-set hotkey parameter value. In OSD menu, pressing this button to select the
items.
+ / - BUTTON
Use this button to direct control the hotkey function. Press the “+” button to increase
the pre-set hotkey parameter value and the “-” button to decrease the pre-set hotkey
parameter value. In OSD menu, pressing this button to adjust the settings.
OSD BACK BUTTON Use to display the OSD menu and go to the previous OSD screen.
OSD NEXT BUTTON Use to display the OSD menu and go to the next OSD screen.
DISPLAY BUTTON Use to view an on-screen information. When OSD menu displayed, press this button
to turn it off.
AV/TV BUTTON Use to select the input source. (VGA/DVI/..)
SOUND (ZOOM) BUTTON Use to display the zoom menu. Press the “+” to zoom in the picture and the
“-” to zoom out the picture.
PLAY (YPbPr) BUTTON Press this button in the non OSD menu display mode to select Component 1 source.
STOP (VGA) BUTTON Press this button in the non OSD menu display mode to select VGA source.
DVI BUTTON Press this button in the non OSD menu display mode to select DVI source.
P/N 559000106-3 :
DigitalView remote control unit
(without DV logo silk screen
printing)
P/N 559000105-3 :
DigitalView remote control unit
(with DigitalView logo silk screen
printing)
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
54 of 60
Appendix VI – PIP mix table
VGA 1
(P1)
VGA 2
(P2/CN6)
DVI
(P2)
Composite 1
(J2/CNV1/CNV5)
Composite 2
(CNV5)
S-Video 1
(J1/CNV1/CNV5)
S-Video 2
(CNV5)
HD Component 1
(CNV2) HD-SDI 1** HD-SDI 2
##
VGA 1 (P1) X X
X
VGA 2 (P2/CN6) X X
X
DVI (P2)
X
Composite 1
(J2/CNV2/CNV5)
X
X
X
X
Composite 2
(CNV5)
X
X
X
X
S-Video 1
(J1/CNV1/CNV5)
X
X
X
X
S-Video 2
(CNV5)
X
X
X
X
HD-Component 1
(CNV2) X
X
X X X X X
HD-SDI 1**
X
X
HD-SDI 2
##
X
X
** - via HD-1000/HD-2000
## - via HD-2000
SVH-1920v2 & HD-1000 I HD-ZODO connection : KH—H 9.9%.? ME? [‘IWIW] mm W «M I
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
55 of 60
Appendix VII – HD-1000 / HD-2000 connection
SVH-1920v2 & HD-1000 / HD-2000 connection :
Set JC1-3 funclion “Pro-rammi mode" word 5 will dis-Ia on screen on thet ngrhnmplnu lind-
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
56 of 60
Appendix VIII – Procedure for showing how to select the baud rate
Jumper function :
JC1-3 = Closed : Enable the baud rate selection function
JC1-3 = Open : Disable the baud rate selection function and default set as 2400.
STEP 1 :
Set JC1-3 = closed.
STEP 2 :
Press and hold “MENU” button on the OSD switch mount and turn on the controller to enter the
“Programming mode”.
Programming mode wordings will display on screen on the target programming board. (See below) :
Step 3 :
Press “MENU” key to go into the “DDC Programming” & “Set RS232 Baud Rate (CN8)” page.
(See below) :
Step 4 :
Select “Set RS232 Baud Rate(CN8)” setting, then press “+” to enter the sub menu page.
JC1-3 closed to enable
the baud rate selection
function
V $23? Band Rah:
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
57 of 60
Step 5 :
Choose the appropriate baud rate settings (2400 / 4800 / 9600 / 14400 / 19200 / 38400 /
57600 / 115200).
Step 5 :
Press “MENU” key to return previous menu.
Step 6 :
Shut off the controller
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
58 of 60
WARRANTY
The products are warranted against defects in workmanship and material for a period of three (3) year from the date of
purchase provided no modifications are made to it and it is operated under normal conditions and in compliance with the
instruction manual.
The warranty does not apply to:
Product that has been installed incorrectly, this specifically includes but is not limited to cases where electrical short
circuit is caused.
Product that has been altered or repaired except by the manufacturer (or with the manufacturer’s consent).
Product that has subjected to misuse, accidents, abuse, negligence or unusual stress whether physical or electrical.
Ordinary wear and tear.
Except for the above express warranties, the manufacturer disclaims all warranties on products furnished hereunder, including
all implied warranties of merchantability and fitness for a particular application or purpose. The stated express warranties are in
lieu of all obligations or liabilities on the part of the manufacturer for damages, including but not limited to special, indirect
consequential damages arising out of or in connection with the use of or performance of the products.
CAUTION
Whilst care has been taken to provide as much detail as possible for use of this product it cannot be relied upon as
an exhaustive source of information. This product is for use by suitably qualified persons who understand the nature
of the work they are doing and are able to take suitable precautions and design and produce a product that is safe
and meets regulatory requirements.
LIMITATION OF LIABILITY
The manufacturer’s liability for damages to customer or others resulting from the use of any product supplied hereunder shall
in no event exceed the purchase price of said product.
TRADEMARKS
The following are trademarks of Digital View Ltd:
Digital View
SVH-1920v2
ussalestugmwew com uksalestugnalvuew com hksalestugmwew com www,diml.11ucw.cmn
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
59 of 60
CONTACT DETAILS
Digital View has offices in Asia, Europe and USA :
USA
Digital View Inc.
18440 Technology Drive
Building 130
Morgan Hill,
California, 95037
USA
Tel: (1) 408-782 7773 Fax: (1) 408-782 7883
Sales: ussales@digitalview.com
EUROPE
Digital View Ltd.
The Lake House
Knebworth Park
Herts, SG3 6PY
UK
Tel: +44-(0)20-7631-2150 Fax: Fax: +44-(0)20-7631-2156
Sales: uksales@digitalview.com
ASIA
Digital View Ltd
Units 705-708, 7/F Texwood Plaza
6 How Ming Street
Kwun Tong
Hong Kong
Tel: (852) 2861 3615 Fax: (852) 2520 2987
Sales: hksales@digitalview.com
WEBSITE
www.digitalview.com
Date Rev No. Page Summary 30 Oct 2015 100 All First issued 44-45 - Add text overlay function RS-232 commands. command and default PIP size. Plug Detect" pint 15 Aug 2016 5‘00 13 & 22 - Revised matching CNVZ connector to 'PHR-6' different resolution panel.
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 6.00: 22 Nov, 2018 (SVH-1920v2-4x_manual.doc) Page
60 of 60
Revision History
Date Rev No.
Page Summary
30 Oct 2015 1.00 All First issued
10 Feb 2016 2.00 8
12
19
22
31
44-45
Add "Volume" adjustment function on OSD
menu page.
Add a remark to state the limitation of the
image orientation function.
Add the definition of SW3 position 8 for video
lock function.
- Correct typo for the definition of CNV2 pin 3 is
Pb and pin 4 is Pr
- Add "Use of memory on board" section in the
Specification table.
- Add text overlay function RS-232 commands.
29 Apr 2016 3.00 24-25
38
- Revised J4 pin definition
- Add default value and range for PIP H position
(0xa4) & PIP V position (0xa5) RS-232
command and default PIP size.
15 Aug 2016 4.00 10, 38
19
26
- Add standard Gamma selection (0.6~2.6)
support on OSD menu and RS-232 command
(0x9d) start effective from V1.18.00.00
firmware version.
- Add SVGA & VGA panel timings selection in
table 2.
- Revised DVI connector (P2) pin 16 to "Hot
Plug Detect" pin.
15 Aug 2016 5.00 13 & 22 - Revised matching CNV2 connector to 'PHR-6'
22 Nov 2016 6.00
3, 13, 18,
27
12, 41
12, 37
14
16, 17
19
20
For SVH-1920v2 (P/N 41752004X-3) :
- Update PCBA diagram
- Add monochrome mode on OSD menu and
RS-232 command control.
- Add "Image Orientation" on Hotkey 1 &
Hotkey 2 on OSD menu and RS-232
command.
- Change to use JST B3B-XH-A compatible type
connector on LED1.
- Add 10V panel power selection jumper on JA3
- Add three new panel timings support on SW3
dip switch setting table done on V1.26.00.00
firmware.
- Support "Resolution default by EDID" for
different resolution panel.

Products related to this Datasheet

LCD DRVR BRD INFRARED SVH-1920V2
Available Quantity: 20
Unit Price: 522.72