1.2mm Sealed Conn System Appl Spec Datasheet by Molex

View All Related Products | Download PDF Datasheet
molex 1 e, 2 REVISION. ECR/ECN \NFORMATION. TITLE. SHEET No. EC No. DATE. DOCUMENT NUMBER. CREATED / REVISED BY. CHECKED BY. APPROVED BY. AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
1 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
1.0 Scope: This manual contains supplemental information pertaining to the Molex 1.2mm Sealed product line,
Molex series numbers 34899 and 34900
2.0 Product Description: The Molex 1.2 sealed system is a series of connectors with 1x2, 1x3, 1x4 and 1x6
terminal configurations, designed to be used with the following Tyco 1.2 MCON terminals
1452665-3
MCON-1.2 LL (Locking- Lance) Receptacle terminal
(wire size 0.25 - 0.35mm²)
1452668-3
MCON-1.2 LL (Locking- Lance) Receptacle terminal
(wire size 0.50 - 0.75mm²)
7-1452671-1
MCON-1.2 LL (Locking-Lance) Receptacle terminal
(wire size 1.0 - 1.5mm²)
2141114-3
MCON-1.2 CB (Clean- Body) Blade terminal
(wire size 0.25 - 0.35mm²)
2141116-3
MCON-1.2 CB (Clean- Body) Blade terminal
(wire size 0.50 - 0.75mm²)
Or the following Kostal MLK 1.2 terminals
32124734110
MLK-1.2mm Single wire seal LL (Locking- Lance) receptacle
terminal (wire size 0.35mm²)
32124734120
MLK-1.2mm Single wire seal LL (Locking- Lance) receptacle
terminal (wire size 0.5mm²)
32124734130
MLK-1.2mm Single wire seal LL (Locking- Lance) receptacle
terminal (wire size 0.75 - 1.0mm²)
Male Terminal Connector
Female Terminal Connector
molex REVISION. ECR/ECN \NFORMATION. TITLE. SHEET N0. EC No. DATE. DOCUMENT NUMBER. CREATED / REVISED EV. CHECKED EV. APPROVED BY. AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
2 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
3.0 Reference Documents:
3.1 Molex Drawings
SD-34899-2001
1.2mm Sealed Inline 1 x 2, 1 x 3 Blade Assembly
SD-34899-6001
1.2mm Sealed Inline 1 x 4, 1 x 6 Blade Assembly
SD-34900-2001
1.2mm Sealed Inline 1 x 2, 1 x 3 Receptacle Assembly
SD-34900-6001
1.2mm Sealed Inline 1 x 4, 1 x 6 Receptacle Assembly
PS-34900-0001
1.2mm Sealed Inline Product Specification
PK-31301-898
1.2mm Sealed Inline Packaging Specification
SD-34996-1501
Cavity Plug Pin
SD-34996-1901
Cavity Plug Seal
3.2 Tyco Drawings
C-1452674
Rev. C2
Single wire sealed receptacle terminals (Locking Lance)
C-1418754
Rev. C6
Single wire sealed blade terminals (Locking Lance)
C-1718398
Rev. B4
Single wire sealed blade terminals (Clean Body)
967056GEN
Rev. B1
Rubber plug for cavity DIA 3.45
3.3 Kostal Drawings
DOC00079128
Rev. 03
Single Wire sealed receptacle terminals (Locking Lance)
molex REVISION: ECR/ECN INFORMATION: TITLE: SHEET N0. EC N : DATE: DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
3 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.0 Procedure
4.1 General Requirements:
4.1.01 Receptacle Terminals
4.1.02 Blade Terminals
4.2 Assembly Instructions:
4.2.01 Connector Assembly, as shipped:
The PLR/ISL is shown in the as shipped position. The PLR/ISL should remain in the pre-
lock position until all circuits are fully loaded. THE PLR/ISL SHOULD NEVER BE REMOVED
FROM THE ASSEMBLY!
4.2.02 ISL “slide to pre-lock”
If during shipping the connector ISL moves from its pre-lock position, it must be moved
back to its pre-lock position. The ISL must be in pre-lock position to populate the
connector. Slide a small (3.5mm maximum) slotted tip screwdriver under the edge of the
ISL on one side. Using the blade of the screwdriver gently slide the ISL out. THE ISL
SHOULD NEVER BE FULLY REMOVED!
Cutaway view of male
connector shown for
clarity
molex REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. EC No: DATE: DOCUMENT NUMBER: CREATED / REVISED BV: CHECKED BV: APPROVED BV: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
4 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.2.03 If during shipping the Connector PLR moves from its pre-lock position, it must be moved
back to its pre-lock position. The PLR must be in pre-lock position to populate the
connector. Using a set of serrated tip tweezers (refer to section 5.0 for details), grab the
center rib feature of the PLR and lift the PLR to the pre-lock position. The PLR should
never be fully removed!
molex REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. EC N : DATE: DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
5 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.2.04 Molex Cavity Plug Installation
4.2.04.1 A 2-piece assembly is available for plugging un-used circuits in the
connector assembly. This assembly consists of a seal, part number 349961902
and a plastic pin, Part Number 349961501. The cavity plug should be installed
prior to terminal insertion.
4.2.04.2 The seal is to be installed over the long, cylindrical portion of the pin and
pressed on until it contacts the head of the pin
molex REVISION: ECR/ECN INFORMATION: TITLE: SHEET N0. EC N : DATE: DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
6 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.2.04.3 The cavity plug assembly can then be installed into the connector.
NOTE: Care should be taken while installing the cavity plug assembly so that the
seal is not pinched.
- Insert the plug assembly into the circuit you wish to plug and carefully press
the cavity plug in until the head of the pin is flush with the surface of the
connector
A pinched seal may increase the force required to completely seat the cavity plug.
molex REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. EC No: DATE: DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BV: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
7 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.2.05 TE Cavity Plug #967056-1
4.2.05.1 Installation per TE Application Specification 114-18025
4.2.06 Terminal Installation Blade and receptacle
4.2.06.1 With ISL/PLR in pre-lock position, orient terminal to rear of connector.
Grip the wire no less than 1.25 inches from the terminal insulation crimp and
insert through appropriate circuit opening. If resistance is encountered, retract
the terminal and adjust the angle of insertion. Continue inserting the terminal
until it stops and locks up on the lock finger.
Cable seal terminal
orientation feature
(proper orientation)
REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. EC No: DATE: DOCUMENT NUMBER: CREATED / REVISED BV: CHECKED BV: APPROVED BV: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
8 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
After installing the terminals, use a small (3.5mm maximum) slotted tip screwdriver to
seat the PLR. Care should be taken to prevent damaging the terminal blades.
Cable seal terminal
orientation feature
(proper orientation)
molex REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. EC N : DATE: DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
9 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
After Installing the terminals, push the ISL into the lock position. If the ISL is
difficult to seat, verify that all terminals are seated properly.
4.2.07 Harness taping recommendation
There should be a minimum of 15mm between the back of the connector and the tape
used on the wire harness.
The PLR/ISL must be closed prior to the taping operation.
The tape must not contact the connector housing.
molex REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. EC No: DATE: DOCUMENT NUMBER: CREATED / REVISED BV: CHECKED BV: APPROVED EV: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
10 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.3 Connector Mating
4.3.01 Begin mating procedure by sliding the connector and header together, press firmly until
the connectors are fully mated and locked
molex REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. EC No: DATE: DOCUMENT NUMBER: CREATED / REVISED BV: CHECKED BV: APPROVED BV: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
11 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.3.02 Once the connector halves are mated, seat the CPA by pressing in the center of the
CPA until positive engagement is felt
4.4 Connector Un-mating
4.4.01 Disengage the CPA by pulling back as shown
molex REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. EC N : DATE: DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
12 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.4.02 Push the connector halves together to unload the pressure on the latch system
4.4.03 Depress the latch with your thumb and hold it down while gently pulling the connector
halves apart
molex REVISION: ECR/ECN INFORMATION: TITLE: SHEET N0. EC No: DATE: DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
13 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.5 Terminal servicing
4.5.01 Male Connector
4.5.01.1 Lift the PLR to the pre-lock position using a set of serrated tip tweezers
(refer to section 5.0 for details); grab the center rib feature of the PLR and lift the
PLR to the pre-lock position.
THE PLR SHOULD NEVER BE FULLY REMOVED!
Magnified view (male connector)
Use serrated, medium
tweezers to lift PLR to
pre-lock position. Grab
the center rib feature of
the of PLR
molex REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. EC No: DATE: DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
14 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.5.01.2 Disengage the terminal lock finger by inserting the service tool (Molex
#63824-2900) through the service hole in the PLR. Push straight down gently
and apply pressure to release the lock finger/ This motion will release the lock
finger, “picking” is not required
PLR in locked
position
PLR in
unlocked
position
terminal REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. EC N : DATE: DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
15 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.5.01.3 While holding pressure on the lock finger with the service tool, gently pull
on the wire to remove the terminal
Holes to insert
service tool to
disengage
terminal
REVISION: ECR/ECN INFORMATION: TITLE: SHEET N0. EC N : DATE: DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
16 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.5.02 Female connector
4.5.02.1 Slide a small (3.5mm maximum) slotted tip screwdriver under the edge of
the ISL on one side. Using the blade of the screwdriver gently slide the ISL out.
THE ISL SHOULD NEVER BE FULLY REMOVED!
Magnified view showing
Service hole to insert tool
to disengage the terminal
ISL in
locked
position
ISL in
unlocked
position
Do not insert the
service tool in to the
receptacle terminal;
damage to the
contact beam will
occur
molex REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. EC N : DATE: DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
17 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.5.02.2 Disengage the terminal by inserting the service tool (Molex #63824-2900)
through the service hole in the PLR. Push straight down gently and apply
pressure to release the terminal, “picking” is not required
4.5.02.3 While holding pressure on the terminal release feature with the service
tool, gently pull on the wire to remove the terminal.
molex 1X1 www.|onestarindustrial.com REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. EC No: DATE: DOCUMENT NUMBER: CREATED / REVISED BV: CHECKED BV: APPROVED BV: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
18 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.6 Electrical Continuity Checking
4.6.01 Male Connector
4.6.01.1 Recommended Pogo Pin
Lone Star Industrial part number LS054RS-318 with the standard spring
force (3.7oz) option (or equivalent).
www.lonestarindustrial.com
4.6.01.2 Pogo Pin Contact Point
4.6.01.3 Pogo Pin Patterns
The pogo pin is
positioned to contact
the tip of the blade
terminal.
molex ‘Xl www.|onestarindustrial.com 1X6 REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. EC N : DATE: DOCUMENT NUMBER: CREATED / REVISED BV: CHECKED BV: APPROVED BV: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
19 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.6.02 Female Connector
4.6.02.1 Recommended Pogo Pin
Lone Star Industrial part number LS054RS-312 with the standard spring
force (3.7oz) option (or equivalent).
www.lonestarindustrial.com
4.6.02.2 Pogo Pin Contact Point
The pogo pin is
positioned to contact
the visible edge of
the terminal box
located within the
terminal service hole
molex 1x2 1K! 1 x & 1 X ‘ REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. EC N : DATE: DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
20 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
4.6.02.3 Pogo Pin Patterns
molex http:llww‘excelta‘com/product cateqories/qeneraI-purpose- tweezers/products/straiqht-tip-medium-point-tweezer REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. EC No: DATE: DOCUMENT NUMBER: CREATED / REVISED BV: CHECKED BV: APPROVED BV: AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
21 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
5.0 Service tool information
5.1 Slotted tip screwdriver with a maximum tip width of 3.5 mm
5.2 Straight tip, serrated, medium point tweezers
5.2.01 Reference: http://www.excelta.com/product_categories/general-purpose-
tweezers/products/straight-tip-medium-point-tweezer
5.3 Terminal service tool: Molex Part Number 638242900
5.4 Alternative Terminal Service tool: GM #J-38125-22
molex REVISION. ECR/ECN \NFORMATION. TITLE. SHEET No. EC No. DATE. DOCUMENT NUMBER. CREATED / REVISED EV. CHECKED EV. APPROVED BY. AS-34900-0001
MXP120 Sealed Connection System
Application Specification
REVISION:
ECR/ECN INFORMATION:
TITLE:
MXP120 Sealed Connection System
SHEET No.
D3
EC No:
UAU2016-0871
22 of 22
DATE:
2015/12/08
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
AS-34900-0001
J. Burgio
M. Vanslambrouck
V. Koshy
TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC
6.0 Revision Information
Revision
Date
Description
1
8/1/2012
Initial draft
A
1/30/2014
Updated with 1x3, 1x4 CKT sizes and added Kostal terminal
part#
B
6/27/2014
Removed Tyco ‘Locking Lance’ blade terminals, Added photos of
service tools
C
1/21/2015
Removed USCAR interface drawing information; Added cavity
plug installation procedure. Added GM service and probe tool
information.
D
3/16/2015
Added fixture probing information. Removed GM probing tool
information.
D1
4/27/2015
Added taping recommendation
D3
12/08/2015
LL terminal added for 1.0 1.5mm² wire size. Addition of TE
Cavity Plug #967056-1.

Products related to this Datasheet

CONN RCPT HSG 3POS 4.00MM
Available Quantity: 5,598
Unit Price: 1.13
CONN RCPT HSG 3POS 4.00MM
Available Quantity: 4,986
Unit Price: 1.2
CONN RCPT HSG 6POS 4.00MM
Available Quantity: 3,474
Unit Price: 2.05
CONN RCPT HSG 4POS 4.00MM
Available Quantity: 2,377
Unit Price: 1.38
CONN RCPT HSG 6POS 4.00MM
Available Quantity: 2,038
Unit Price: 2.05
CONN RCPT HSG 2POS 4.00MM
Available Quantity: 1,878
Unit Price: 0.94
SLD M BLADE CONN 2CRCT YL
Available Quantity: 1,632
Unit Price: 1.32
CONN RCPT HSG 4POS 4.00MM
Available Quantity: 1,395
Unit Price: 1.38
SLD M BLADE CONN 2CRCT YL
Available Quantity: 0
Unit Price: 0
CONN PLUG HSG 6POS 4.00MM
Available Quantity: 0
Unit Price: 1.36927
CONN RCPT HSG 3POS 4.00MM
Available Quantity: 0
Unit Price: 0
CONN PLUG HSG 3POS 4.00MM
Available Quantity: 0
Unit Price: 0.66672
CONN PLUG HSG 3POS 4.00MM
Available Quantity: 0
Unit Price: 0
CONN PLUG HSG 6POS 4.00MM
Available Quantity: 0
Unit Price: 1.05525
CONN PLUG HSG 6POS 4.00MM
Available Quantity: 0
Unit Price: 0
CONN PLUG HSG 6POS 4.00MM
Available Quantity: 0
Unit Price: 0
CONN PLUG HSG 6POS 4.00MM
Available Quantity: 0
Unit Price: 0
CONN RCPT HSG 4POS 4.00MM
Available Quantity: 0
Unit Price: 1.17837
CONN RCPT HSG 4POS 4.00MM
Available Quantity: 0
Unit Price: 1.17837
CONN RCPT HSG 6POS 4.00MM
Available Quantity: 0
Unit Price: 1.01742
CONN RCPT HSG 6POS 4.00MM
Available Quantity: 0
Unit Price: 1.01742
CONN RCPT HSG 6POS 4.00MM
Available Quantity: 0
Unit Price: 2.1
CONN RCPT HSG 6POS 4.00MM
Available Quantity: 0
Unit Price: 1.01742
CONN RCPT HSG 6POS 4.00MM
Available Quantity: 0
Unit Price: 1.01742