Chip Filters Catalog Datasheet by Taiyo Yuden

View All Related Products | Download PDF Datasheet
TAIYD YUDEN 2019
Notice for TAIYO YUDEN Products
[ For the TAIYO YUDEN Products excluding
Ceramic Capacitors and Inductors ]
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
Product information in this catalog is as of October 2018. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully
before practical application or use of our products.
Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or
equipment incorporating our products, which are caused under the conditions other than those specified in this
catalog or individual product specification sheets.
Please contact TAIYO YUDEN for further details of product specifications as the individual product specification
sheets are available.
Please conduct validation and verification of our products in actual condition of mounting and operating
environment before using our products.
The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA
equipment, home electric appliances, office equipment, information and communication equipment including,
without limitation, mobile phone, and PC). Please be sure to contact TAIYO YUDEN for further information
before using the products for any equipment which may directly cause loss of human life or bodily injury (e.g.,
transportation equipment including, without limitation, automotive powertrain control system, train control system,
and ship control system, traffic signal equipment, disaster prevention equipment, medical equipment classified
as Class I, II or III by IMDRF, highly public information network equipment including, without limitation, telephone
exchange, and base station).
Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g.,
aerospace equipment, aviation equipment, medical equipment classified as Class IV by IMDRF, nuclear control
equipment, undersea equipment, military equipment).
When our products are used even for high safety and/or reliability-required devices or circuits of general electronic
equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to
install a protection circuit as necessary.
Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way
responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog
for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above.
Information contained in this catalog is intended to convey examples of typical performances and/or applications
of our products and is not intended to make any warranty with respect to the intellectual property rights or any
other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights.
Please note that the scope of warranty for our products is limited to the delivered our products themselves and
TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products.
Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality
assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in
accordance with such agreement.
The contents of this catalog are applicable to our products which are purchased from our sales offices or
authorized distributors (hereinafter TAIYO YUDENs official sales channel). Please note that the contents of this
catalog are not applicable to our products purchased from any seller other than TAIYO YUDENs official sales
channel.
Caution for Export
Some of our products listed in this catalog may require specific procedures for export according to U.S. Export
Administration Regulations, Foreign Exchange and Foreign Trade Control Law of Japan, and other applicable
regulations. Should you have any questions on this matter, please contact our sales staff.
19
‘fi ‘1'" |:||:||:l|:l|:l|:l|:l nnvoUn nnvoUo TAIYD YUDEN 2015
HIGH FREQUENCY PRODUCTS
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
MULTILAYER CERAMIC DEVICES / DIPLEXERS / COUPLER / 2 BRANCH COUPLER
REFLOW
chipfilter_e-E07R01
MULTILAYER CERAMIC DEVICES / DIPLEXERS / COUPLER / 2 BRANCH COUPLER
REFLOW
PARTS NUMBER
F I 2 1 2 B 2 4 5 0 2 6 - T △=Blank space
Series name
Code Series name
FI High frequency devices
Electrode code
Code Electrode code
With plating
Dimensions
Code Dimensions[mm]
212 2.0×1.25
168 1.6×0.8
105 1.0×0.5
Special code
Code Special code
B Band pass type
L Low pass type
H High pass type
C Balance type
P Diplexer
W 2 Branch coupler
D Dual type
K Coupler
⑤Frequency
Code
(example) Frequency[MHz]
2450 2400~2500
0620 470~770
⑥Spec code
Code Spec code
01~ Individual spec
⑦Packaging
Code Packaging
-T Taping
EXTERNAL DIMENSIONS / STANDARD QUANTITY
FI 212B type FI 168B/L type FI 105B/L type FI 168L0628M4
0
.9
±
0
.10
0
.30
±
0
.20
2.
0
±
0
.15
1.25±0.15
GND
GND
IN OUT
1.6±0.20
0.5max.
0.30±0.10
1.6±0.10
0.80±0.10
GND
GND
IN OUT
0
.7±
0
.10
0.
4
m
ax.
0.30±0.10
1.00±0.05
0.50±0.05
GND
GND
I
OUT
0.30±0.10
0
.10
±
0
.05
0.10±0.05
0.65max.1.6±0.10
0.80±0.10
(1) (2) (3)
(6) (5) (4)
0.50±0.15
0.2±0.10
FI 168L****G* type FI 168H type FI 168D type FI 212C245033
0.65max.1.6±0.10
0.80±0.10
(1) (2) (3)
0.70±0.10
(1) (2) (3)
0.60±0.10
0.40±0.10
0
.30±0.10 0.30±0.10
0.60±0.10
0.65max.1.6±0.10
0.80±0.10
(1) (2) (3)
0.70±0.10
(1) (2) (3)
0.60±0.10
0.40±0.10
0
.30±0.10 0.30±0.10
0.60±0.10
0
.45m
a
x.
1
.6
±
0
.10
0.80±0.10
(6) (5) (4)
(1) (2) (3)
0.50±0.15
0
.2
±
0
.15
0.9±0.10
0
.30
±
0
.20
2.0±0.15
1.25±0.15
(7) (6) (5)
(1) (2) (3)
(
8) (4)
0.65±0.20
0.3±0.20
FI 212C type FI 212C245075 FI 168P type FI 212P type
0
.
9
±
0
.10
0
.30±
0
.20
2
.
0
±
0
.15
1.25±0.15
(7) (6) (5)
(1) (2) (3)
(
8) (4)
0.65±0.20
0.3±0.20
0
.
7
m
ax.
0.30±0.20
2
.
0
±
0
.15
1.25±0.15
(7) (6) (5)
(1) (2) (3)
(
8) (4)
0.65±0.20
0.3±0.20
0.65
m
a
x.1.6
±
0.10
0.80±0.10
(6) (5) (4)
(1) (2) (3)
0.50±0.150.2±0.1
0.9±0.10
2
.0±0.15
1.25±0.15
(6) (5) (4)
(1) (2) (3)
0.65±0.20
0.
3
±0.20
Unit::mm
148
19
TAIYC) YUDEN 2019
HIGH FREQUENCY PRODUCTS
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
chipfilter_e-E07R01
FI 212P****G* type FI 168W type FI168K type
0
.
9±0
.
10
2
.
0±0
.
15
1.25±0.15
(1) (2) (3)
(6) (5) (4)
0.65±0.10
0.3±0.10
0.30±0.10
0.05typ
(6) (5) (4)
(1) (2) (3)
0.
5
max.
0.20±0.15
1.6±0.10
0.80±0.10
(7) (6) (5)
(1) (2) (3)
(8) (4)
0.50±0.15
0.2±0.15
0.65max.1.6±0.10
0.80±0.10
(6) (5) (4)
(1) (2) (3)
0.50±0.150.20±0.15
Unit:mm
FI 168L0628M4 FI 168L****G* type FI 168H type FI 168D087018 FI 212C2450** FI 168P245030
(1) I/O Port RF IN/OUT RF IN/OUT High Band IN Balanced GND
(2) GND GND GND GND GND Common
(3) I/O Port RF IN/OUT RF IN/OUT Low Band IN Balanced GND
(4) GND - - Low Band OUT GND Low Band
(5) GND - - GND Unbalance GND
(6) GND - - High Band OUT DC High Band
(7) - - - - NC -
(8) - - - - GND -
FI 212P****G* type FI 212P089208
FI 212P085912
FI 212P089213
FI 212P085909 FI 168P157519 FI 168W type FI 168K type
(1) Low Band GND GND GND RF1 IN/OUT COUPLING
(2) GND Common Port Common Port High Band CPL2 RF1 GND
(3) High Band GND GND Common CPL2 RF2 ISOLATION
(4) GND High Band Low Band Low Band GND RF OUT
(5) Common GND GND - RF2 OUT/IN GND
(6) GND Low Band High Band - CPL1 RF2 RF IN
(7) - - - - CPL1 RF1 -
(8) - - - - GND -
Type Standard quantity[pcs]
212 3000~6000
168 4000~8000
105 10000
149
19
TAIYC) YUDEN 2019
HIGH FREQUENCY PRODUCTS
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
PARTS NUMBER
Multilayer device band pass type
Applications External dimensions [mm] Part number
2.0×1.25×1.0max. FI 212B245026
2.0×1.25×1.0max. FI 212B245027
1.6×0.8×0.5max. FI 168B245001
1.0×0.5×0.4max. FI 105B245024
Multilayer device low pass type
Applications External dimensions [mm] Part number
Digtal TV 1.6×0.8×0.45max. FI 168L062005
2.4GHz W-LAN /
Bluetooth
® 1.0×0.5×0.4max. FI 105L250014
1.0×0.5×0.4max. FI 105L186822
1.0×0.5×0.4max. FI 105L087038
1.6×0.8×0.65max. FI 168L0628M4
1.6×0.8×0.65max. FI 168L2200G9
1.6×0.8×0.65max. FI 168L1681G6
Multilayer device high pass type
Applications External dimensions [mm] Part number
Cellular 1.6×0.8×0.65max. FI 168H2593GG
Applications External dimensions [mm] Part number Notes
Other 1.6×0.8×0.45max. FI 168D087018 Dual band LPF
Multilayer device balance type
Applications External dimensions [mm] Part number Notes
Bluetooth
® 2.0×1.25×1.0max. FI 212C245033 Conjugated match to CSR BC3
2.0×1.25×1.0max. FI 212C245036 Conjugated match to CSR BC5
2.0×1.25×0.7max. FI 212C245075 Conjugated match to CSR BC5FM, BC6ROM
Multilayer diplexer
Applications External dimensions [mm] Part number
W-LAN 1.6×0.8×0.65max. FI 168P245030
2.0×1.25×1.0max. FI 212P082931
2.0×1.25×1.0max. FI 212P0829G2
2.0×1.25×1.0max. FI 212P082934
2.0×1.25×1.0max. FI 212P082935
2.0×1.25×1.0max. FI 212P089208
2.0×1.25×1.0max. FI 212P089213
2.0×1.25×1.0max. FI 212P085909
2.0×1.25×1.0max. FI 212P085912
1.6×0.8×0.65max. FI 168P157519
1.6×0.8×0.65max. FI 168P157525
Multilayer coupler
Applications External dimensions [mm] Part number
1.6×0.8×0.5max. FI 168W1697B1
1.6×0.8×0.5max. FI 168K1687AA
GPS / 2.4GHz W-LAN
Cellular
2.4GHz W-LAN /
Bluetooth
®
Cellular
Cellular
chipfilter_e-E07R01
150
19
TAIYC) YUDEN 2015
HIGH FREQUENCY PRODUCTS
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
ELECTRICAL CHARACTERISTICS / TYPICAL CHARACTERISTICS
FI 212B245026
Pass band frequency 2400 - 2500 MHz
Insertion loss at pass band 2.6 dB max. (+25℃)
2.9 dB max. (-40~+85℃)
Ripple at pass band 1.0 dB max.
V.S.W.R. at pass band 2.0 max.
Attenuation 40 dB min. (800 - 960 MHz)
30 dB min. (1710 - 1990 MHz)
25 dB min. (2110 - 2170 MHz)
30 dB min. (4800 - 5000 MHz)
30 dB min. (7200 - 7500 MHz)
Impedance 50 Ω
FI 212B245027
Pass band frequency 2400 - 2500 MHz
Insertion loss at pass band 1.4 dB max. (+25℃)
1.7 dB max. (-40~+85℃)
Ripple at pass band 1.0 dB max.
V.S.W.R. at pass band 2.0 max.
Attenuation 30 dB min. (800 - 915 MHz)
30 dB min. (1710 - 1910 MHz)
6 dB min. (2110 - 2170 MHz)
20 dB min. (4800 - 5000 MHz)
FI 168B245001
Pass band frequency 2400 - 2500 MHz
Insertion loss at pass band 2.2 dB max. (+25℃)
2.5 dB max. (-30~+85℃)
Ripple at pass band 1.0 dB max.
V.S.W.R. at pass band 2.1 max.
Attenuation 25 dB min. (800 - 960 MHz)
25 dB min. (1710 - 1910 MHz)
20 dB min. (4800 - 5000 MHz)
20 dB min. (7200 - 7500 MHz)
Impedance 50 Ω
FI 105B245024
Pass band frequency 2400 - 2500 MHz
Insertion loss at pass band 3.0 dB max. (+25℃)
3.3 dB max. (-40~+85℃)
Ripple at pass band 1.0 dB max.
V.S.W.R. at pass band 2.2 max.
Attenuation 25 dB min. (800 - 960 MHz)
22 dB min. (1710 - 1910 MHz)
20 dB min. (4800 - 5000 MHz)
20 dB min. (7200 - 7500 MHz)
FI 168L062005
Pass band frequency 470 - 770 MHz
Insertion loss at 470 - 600 MHz 1.2 dB max. (+25℃)
1.3 dB max. (-30~+85℃)
Insertion loss at 600 - 710 MHz 2.2 dB max. (+25℃)
2.4 dB max. (-30~+85℃)
Insertion loss at 710 - 770 MHz 4.0 dB max. (+25℃)
4.4 dB max. (-30~+85℃)
Ripple at 470 - 710 MHz 1.4 dB max.
V.S.W.R. 2.0 max. (470 - 710 MHz)
2.5 max. (710 - 770 MHz)
Attenuation 25 dB min. (888 - 925 MHz) (+25℃)
21 dB min. (888 - 925 MHz) (-30~+85℃)
25 dB min. (940 - 960 MHz)
27 dB min. (1429 - 1453 MHz)
26 dB min. (1920 - 1980 MHz)
26 dB min. (2400 - 2500 MHz)
Impedance 50 Ω
FI 105L250014
Pass band frequency 2400 - 2500 MHz
Insertion loss at 2400 - 2500 MHz 0.45 dB max. (+25℃)
0.55 dB max. (-40~+85℃)
V.S.W.R. at 2400 - 2500 MHz 1.7 max.
Attenuation 21 dB min. (4800 - 5000 MHz)
21 dB min. (7200 - 7500 MHz)
Impedance 50 Ω
chipfilter_e-E07R01
151
19
l g .n w u u u a u u 7; u ”mum mun-49H TAIYC) YUDEN 2015
HIGH FREQUENCY PRODUCTS
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
ELECTRICAL CHARACTERISTICS / TYPICAL CHARACTERISTICS
FI 105L186822
Pass band frequency 824 - 915 MHz
Insertion loss at 824 - 915 MHz 0.75 dB max. (-30~+85℃)
V.S.W.R. at 2400 - 2500 MHz 1.5 max.
Attenuation 23 dB min. (1648 - 1830 MHz)
23 dB min. (2472 - 2745 MHz)
Impedance 50 Ω
FI 105L087038
Pass band frequency 824 - 915 MHz
Insertion loss at 824 - 915 MHz 0.75 dB max. (-30~+85℃)
V.S.W.R. at 2400 - 2500 MHz 1.5 max.
Attenuation 23 dB min. (1648 - 1830 MHz)
23 dB min. (2472 - 2745 MHz)
Impedance 50 Ω
FI 168L0628M4
Pass band frequency 470 - 787 MHz
Insertion loss at pass band 0.5 dB max. (+25℃)
0.6 dB max. (-40~+90℃)
Ripple at pass band -
V.S.W.R. at pass band 2.0 max.
Attenuation 26 dB min. (1429 - 1501 MHz)
30 dB min. (1565 - 1607 MHz)
35 dB min. (1570 - 1580 MHz)
18 dB min. (1920 - 1980 MHz)
Impedance 50 Ω
FI 168L2200G9
Pass band frequency 1700 - 2170 MHz
2170 - 2500 MHz
2500 - 2700 MHz
Insertion loss at 1700 - 2170 MHz 0.5 dB max. (+25℃)
0.55 dB max. (-30~+85℃)
Insertion loss at 2170 - 2500 MHz 0.65 dB max. (+25℃)
0.75 dB max. (-30~+85℃)
Insertion loss at 2500 - 2700 MHz 0.9 dB max. (+25℃)
1.0 dB max. (-30~+85℃)
Return loss. at 1700 - 2700 MHz 10 dB min.
Attenuation 25 dB min. (3400 MHz)
22 dB min. (3400 - 5400 MHz)
20 dB min. (5400 - 8100 MHz)
Impedance 50 Ω
FI 168L1681G6
Pass band frequency 617 - 2690 MHz
0.5 dB max. (-40~+90℃)
Return loss. at 617 - 2690 MHz 10 dB min.
Attenuation 35 dB min. (4950 - 6000 MHz)
35 dB min. (6000 - 7500 MHz)
35 dB min. (7500 - 8100 MHz)
35 dB min. (8100 - 10500 MHz)
27 dB min. (10500 - 12500 MHz)
Impedance 50 Ω
FI 168H2593GG
Pass band frequency 2496 - 2690 MHz
Insertion loss at 2500 - 2700 MHz 0.9 dB max. (-40~+90℃)
Return loss. at 1700 - 2700 MHz 15 dB min.
Attenuation 25 dB min. (1710 - 1995 MHz)
Impedance 50 Ω
60
50
40
30
20
10
0
0.4 0.8 1.2 1.6 2.0 2.4 2.8
Attenuation[dB]
Frequency[GHz]
S11
S21
-60
-50
-40
-30
-20
-10
0
1.0 2.0 3.0 4.0 5.0 6.0 7.0
Attenuation[dB]
Frequency[GHz]
S11
S21
-60
-50
-40
-30
-20
-10
0
0.5 1.5 2.5 3.5 4.5 5.5 6.5 7.5 8.5 9.5 10.5 11.512.5
Attenuation[dB]
Frequency[GHz]
S11
S21
-50
-40
-30
-20
-10
0
0.5 1.5 2.5 3.5 4.5 5.5 6.5
Attenuation[dB]
Frequency[GHz]
S11
S21
chipfilter_e-E07R01
152
19
TAIYC) YUDEN 2015
HIGH FREQUENCY PRODUCTS
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
ELECTRICAL CHARACTERISTICS / TYPICAL CHARACTERISTICS
FI 168D087018
Low band
Pass band frequency 824 - 915 MHz
Insertion loss at 824 - 915 MHz 0.6 dB max. (-30~+85℃)
V.S.W.R. at 824 - 915 MHz 1.5 max.
Attenuation 25 dB min. (1648 - 1830 MHz)
25 dB min. (2472 - 2745 MHz)
Impedance 50 Ω
High band
Pass band frequency 1710 - 1910 MHz
Insertion loss at 1710 - 1910 MHz 0.6 dB max. (-30~+85℃)
V.S.W.R. at 824 - 915 MHz 1.5 max.
Attenuation 25 dB min. (3420 - 3820 MHz)
25 dB min. (5130 - 5730 MHz)
Impedance 50 Ω
Isolation
In to In/Out to Out 27 dB min. (824 - 915 MHz)
30 dB min. (1710 - 1910 MHz)
In to Out 30 dB min. (824 - 915 MHz)
30 dB min. (1710 - 1910 MHz)
FI 212C245033
Pass band frequency 2400 - 2500 MHz
Insertion loss at pass band 2.7 dB (+25℃)
3.0 dB (-30~+85℃)
Ripple at pass band 1.0 dB max.
Unbalanced port V.S.W.R. at pass band 2.0 max.
Balanced port V.S.W.R. at pass band 2.0 max.
Amplitude Imbalance at pass band 2.0 dB max.
Phase Imbalance at pass band 180 ±10℃
Attenuation 25 dB min. (880 - 960 MHz)
15 dB min. (1710 - 1990 MHz)
15 dB min. (1990 - 2170 MHz)
15 dB min. (4800 - 5000 MHz)
Unbalanced port Impedance 50 Ω
Balanced port Impedance Conjugated match to CSR BC3
FI 212C245036
Pass band frequency 2400 - 2500 MHz
Insertion loss at pass band 3.7 dB (+25℃)
4.0 dB (-30~+85℃)
Ripple at pass band 1.0 dB max.
Unbalanced port V.S.W.R. at pass band 2.0 max.
Balanced port V.S.W.R. at pass band 2.0 max.
Amplitude Imbalance at pass band 2.0 dB max.
Phase Imbalance at pass band 180 ±10℃
Attenuation 35 dB min. (880 - 960 MHz)
20 dB min. (1710 - 1990 MHz)
15 dB min. (1990 - 2170 MHz)
20 dB min. (4800 - 5000 MHz)
Unbalanced port Impedance 50 Ω
Balanced port Impedance Conjugated match to CSR BC5
FI 212C245075
Pass band frequency 2400 - 2500 MHz
Insertion loss at pass band 3.7 dB (+25℃)
4.0 dB (-30~+85℃)
Ripple at pass band 1.0 dB max.
Unbalanced port V.S.W.R. at pass band 2.2 max.
Balanced port V.S.W.R. at pass band 2.2 max.
Amplitude Imbalance at pass band 2.0 dB max.
Phase Imbalance at pass band 180 ±10℃
Attenuation 40 dB min. (880 - 960 MHz)
18 dB min. (1710 - 1990 MHz)
12 dB min. (1990 - 2170 MHz)
30 dB min. (4800 - 5000 MHz)
Unbalanced port Impedance 50 Ω
Balanced port Impedance Conjugated match to CSR BC5FM, BC6ROM
chipfilter_e-E07R01
153
19
TAIYC) YUDEN 2015
HIGH FREQUENCY PRODUCTS
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
ELECTRICAL CHARACTERISTICS / TYPICAL CHARACTERISTICS
FI 168P245030
Low band
Pass band frequency 1 1558 - 1610 MHz
Pass band frequency 2 2400 - 2500 MHz
Insertion loss at Pass band 1 0.50 dB max.
Insertion loss at Pass band 2 0.60 dB max.
V.S.W.R. at Pass band 2.0 dB max.
Attenuation 24 dB min. (4800 - 4900 MHz)
26 dB min. (4900 - 6000 MHz)
Impedance 50Ω
High band
Pass band frequency 4900 - 5950 MHz
Insertion loss at Pass band 0.80 dB max.
V.S.W.R. at Pass band 2.0 dB max.
Attenuation 32 dB min. (30 - 2700 MHz)
Impedance 50Ω
FI 212P082931
Low band
Pass band frequency 1 698 - 894 MHz
Pass band frequency 2 880 - 960 MHz
Insertion loss at 698 - 894 MHz 0.50 dB max. (+25℃)
0.60 dB max. (-40~+85℃)
Insertion loss at 880 - 960 MHz 0.70 dB max. (+25℃)
0.80 dB max. (-40~+85℃)
V.S.W.R. at 698 - 894 MHz 2.0 max.
V.S.W.R. at 880 - 960 MHz 2.0 max.
Attenuation 13 dB min. (1420 - 2690 MHz)
Impedance 50Ω
High band
Pass band frequency 1 1420 - 1520 MHz
Pass band frequency 2 1560 - 1610 MHz
Pass band frequency 3 1710 - 2170 MHz
Pass band frequency 4 2300 - 2690 MHz
Insertion loss at 1420 - 1520 MHz 0.70 dB max. (+25℃)
0.80 dB max. (-40~+85℃)
Insertion loss at 1560 - 1610 MHz 0.50 dB max. (+25℃)
0.60 dB max. (-40~+85℃)
Insertion loss at 1710 - 2170 MHz 0.50 dB max. (+25℃)
0.60 dB max. (-40~+85℃)
Insertion loss at 2300 - 2690 MHz 0.50 dB max. (+25℃)
0.60 dB max. (-40~+85℃)
V.S.W.R. at 1420 - 2690 MHz 2.0 max.
Attenuation 13 dB min. (698 - 960 MHz)
Impedance 50Ω
FI 212P0829G2
Low band
Pass band frequency 698 - 960 MHz
Insertion loss at 698 - 960 MHz 0.27 dB max. (+25℃)
0.32 dB max. (-40~+85℃)
V.S.W.R. at 698 - 960 MHz 2.0 max.
Attenuation 13 dB min. (1710 - 2690 MHz)
Impedance 50Ω
High band
Pass band frequency 1710 - 2690 MHz
Insertion loss at 1710 - 2690 MHz 0.45 dB max. (+25℃)
0.55 dB max. (-40~+85℃)
V.S.W.R. at 698 - 960 MHz 2.0 max.
Attenuation 19 dB min. (698 - 960 MHz)
Impedance 50Ω
-60
-50
-40
-30
-20
-10
0
0 2 4 6 8 10 12 14 16 18
Attenuation/Return Loss [dB]
Frequency. [GHz]
CommonRlo
HighBand
LowBand
chipfilter_e-E07R01
154
19
TAIYC) YUDEN 201B
HIGH FREQUENCY PRODUCTS
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
ELECTRICAL CHARACTERISTICS / TYPICAL CHARACTERISTICS
FI 212P082934
Low band
Pass band frequency 698 - 960 MHz
Insertion loss at 698 - 960 MHz 0.50 dB max. (-40~+85℃)
V.S.W.R. at 698 - 960 MHz 1.4 max.
Attenuation 15 dB min. (1554 - 1580 MHz)
25 dB min. (1710 - 2110 MHz)
25 dB min. (2110 - 2155 MHz)
25 dB min. (2155 - 2690 MHz)
12 dB min. (2155 - 7830 MHz)
Impedance 50Ω
High band
Pass band frequency 1 1710 - 2170 MHz
Pass band frequency 2 2500 - 2690 MHz
Insertion loss at 1710 - 2170 MHz 0.50 dB max. (-40~+85℃)
Insertion loss at 2500 - 2690 MHz 0.55 dB max. (-40~+85℃)
V.S.W.R. at 1710 - 2170 MHz 1.4 max.
V.S.W.R. at 2500 - 2690 MHz 1.8 max.
Attenuation 17 dB min. (0.3 - 960 MHz)
Impedance 50Ω
FI 212P082935
Low band
Pass band frequency 698 - 960 MHz
Insertion loss at 698 - 960 MHz 0.50 dB max. (-40~+85℃)
V.S.W.R. at 698 - 960 MHz 1.4 max.
Attenuation 15 dB min. (1554 - 1580 MHz)
25 dB min. (1710 - 2110 MHz)
25 dB min. (2110 - 2155 MHz)
25 dB min. (2155 - 2690 MHz)
12 dB min. (2155 - 7830 MHz)
Impedance 50Ω
High band
Pass band frequency 1 1710 - 2170 MHz
Pass band frequency 2 2500 - 2690 MHz
Insertion loss at 1710 - 2170 MHz 0.50 dB max. (-40~+85℃)
Insertion loss at 2500 - 2690 MHz 0.55 dB max. (-40~+85℃)
V.S.W.R. at 1710 - 2170 MHz 1.4 max.
V.S.W.R. at 2500 - 2690 MHz 1.8 max.
Attenuation 17 dB min. (0.3 - 960 MHz)
Impedance 50Ω
FI 212P089208
Low band
Pass band frequency 698 - 960 MHz
Insertion loss at 698 - 960 MHz 0.27 dB max. (+25℃)
0.32 dB max. (-40~+85℃)
V.S.W.R. at 698 - 960 MHz 2.0 max.
Attenuation 13 dB min. (1710 - 2170 MHz)
Impedance 50Ω
High band
Pass band frequency 1710 - 2170 MHz
Insertion loss at 1710 - 2170 MHz 0.45 dB max. (+25℃)
0.55 dB max. (-40~+85℃)
V.S.W.R. at 698 - 960 MHz 2.0 max.
Attenuation 19 dB min. (698 - 960 MHz)
Impedance 50Ω
FI 212P089213
Low band
Pass band frequency 698 - 960 MHz
Insertion loss at 698 - 960 MHz 0.27 dB max. (+25℃)
0.32 dB max. (-40~+85℃)
V.S.W.R. at 698 - 960 MHz 2.0 max.
Attenuation 13 dB min. (1710 - 2170 MHz)
Impedance 50Ω
High band
Pass band frequency 1710 - 2170 MHz
Insertion loss at 1710 - 2170 MHz 0.45 dB max. (+25℃)
0.55 dB max. (-40~+85℃)
V.S.W.R. at 698 - 960 MHz 2.0 max.
Attenuation 19 dB min. (698 - 960 MHz)
Impedance 50Ω
chipfilter_e-E07R01
155
19
TAIYC) YUDEN 2019
HIGH FREQUENCY PRODUCTS
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
ELECTRICAL CHARACTERISTICS / TYPICAL CHARACTERISTICS
FI 212P085909
Low band
Pass band frequency 698 - 960 MHz
Insertion loss at 698 - 960 MHz 0.70 dB max. (+25℃)
0.75 dB max. (-30~+85℃)
V.S.W.R. at 698 - 960 MHz 1.6 max.
Attenuation 19 dB min. (1558 - 1570 MHz)
20 dB min. (1570 - 1580 MHz)
19 dB min. (1580 - 1610 MHz)
Impedance 50Ω
High band
Pass band frequency 1 1558 - 1570 MHz
Pass band frequency 2 1570 - 1580 MHz
Pass band frequency 3 1580 - 1610 MHz
Insertion loss at 1558 - 1570 MHz 0.75 dB max. (+25℃)
0.85 dB max. (-30~+85℃)
Insertion loss at 1570 - 1580 MHz 0.70 dB max. (+25℃)
0.80 dB max. (-30~+85℃)
Insertion loss at 1580 - 1610 MHz 0.70 dB max. (+25℃)
0.80 dB max. (-30~+85℃)
V.S.W.R. at 1558 - 1570 MHz 1.6 max.
V.S.W.R. at 1570 - 1580 MHz 1.6 max.
V.S.W.R. at 1580 - 1610 MHz 1.6 max.
Attenuation 35 dB min. (698 - 824 MHz)
42 dB min. (824 - 894 MHz)
25 dB min. (894 - 960 MHz)
Impedance 50Ω
FI 212P085912
Low band
Pass band frequency 698 - 960 MHz
Insertion loss at 698 - 960 MHz 0.70 dB max. (+25℃)
0.75 dB max. (-30~+85℃)
V.S.W.R. at 698 - 960 MHz 1.6 max.
Attenuation 19 dB min. (1558 - 1570 MHz)
20 dB min. (1570 - 1580 MHz)
19 dB min. (1580 - 1610 MHz)
Impedance 50Ω
High band
Pass band frequency 1 1558 - 1570 MHz
Pass band frequency 2 1570 - 1580 MHz
Pass band frequency 3 1580 - 1610 MHz
Insertion loss at 1558 - 1570 MHz 0.75 dB max. (+25℃)
0.85 dB max. (-30~+85℃)
Insertion loss at 1570 - 1580 MHz 0.70 dB max. (+25℃)
0.80 dB max. (-30~+85℃)
Insertion loss at 1580 - 1610 MHz 0.70 dB max. (+25℃)
0.80 dB max. (-30~+85℃)
V.S.W.R. at 1558 - 1570 MHz 1.6 max.
V.S.W.R. at 1570 - 1580 MHz 1.6 max.
V.S.W.R. at 1580 - 1610 MHz 1.6 max.
Attenuation 35 dB min. (698 - 824 MHz)
42 dB min. (824 - 894 MHz)
25 dB min. (894 - 960 MHz)
Impedance 50Ω
FI 168P157519
Low band
Pass band frequency 0 824 - 960 MHz
Pass band frequency 1 1558 - 1585 MHz
Pass band frequency 2 1585 - 1610 MHz
Insertion loss at 824 - 960 MHz 0.50 dB max. (+25℃)
0.60 dB max. (-40~+85℃)
Insertion loss at 1558 - 1585 MHz 0.40 dB max. (+25℃)
0.50 dB max. (-40~+85℃)
Insertion loss at 1585 - 1610 MHz 0.45 dB max. (+25℃)
0.55 dB max. (-40~+85℃)
V.S.W.R. at 824 - 960 MHz 2.0 max.
V.S.W.R. at 1558 - 1585 MHz 2.0 max.
V.S.W.R. at 1585 - 1610 MHz 2.0 max.
Attenuation 13 dB min. (2400 - 2500 MHz)
Impedance 50Ω
High band
Pass band frequency 2400 - 2500 MHz
Insertion loss at 2400 - 2500 MHz 0.60 dB max. (+25℃)
0.70 dB max. (-40~+85℃)
V.S.W.R. at 2400 - 2500 MHz 2.0 max.
Attenuation 12 dB min. (824 - 960 MHz)
23 dB min. (1558 - 1585 MHz)
20 dB min. (1585 - 1610 MHz)
Impedance 50Ω
chipfilter_e-E07R01
156
19
w u u u u Mmum TAIYC) YUDEN 201B
HIGH FREQUENCY PRODUCTS
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
ELECTRICAL CHARACTERISTICS / TYPICAL CHARACTERISTICS
FI 168P157525
Low band
Pass band frequency 0 824 - 960 MHz
Pass band frequency 1 1558 - 1585 MHz
Pass band frequency 2 1585 - 1610 MHz
Insertion loss at 824 - 960 MHz 0.50 dB max. (+25℃)
0.60 dB max. (-40~+85℃)
Insertion loss at 1558 - 1585 MHz 0.40 dB max. (+25℃)
0.50 dB max. (-40~+85℃)
Insertion loss at 1585 - 1610 MHz 0.45 dB max. (+25℃)
0.55 dB max. (-40~+85℃)
V.S.W.R. at 824 - 960 MHz 2.0 max.
V.S.W.R. at 1558 - 1585 MHz 2.0 max.
V.S.W.R. at 1585 - 1610 MHz 2.0 max.
Attenuation 13 dB min. (2400 - 2500 MHz)
Impedance 50Ω
High band
Pass band frequency 2400 - 2500 MHz
Insertion loss at 2400 - 2500 MHz 0.60 dB max. (+25℃)
0.70 dB max. (-40~+85℃)
V.S.W.R. at 2400 - 2500 MHz 2.0 max.
Attenuation 12 dB min. (824 - 960 MHz)
23 dB min. (1558 - 1585 MHz)
12 dB min. (1585 - 1610 MHz)
Impedance 50Ω
FI 168W1697B1
Pass band frequency 699 - 2690 MHz
Insertion loss at 699 - 960 MHz 0.15 dB max. (+35~+85℃)
0.1 dB max. (+15~+35℃)
0.1 dB max. (-20~+15℃)
Insertion loss at 1000 - 2025 MHz 0.25 dB max. (+35~+85℃)
0.2 dB max. (+15~+35℃)
0.2 dB max. (-20~+15℃)
Insertion loss at 2110 - 2690 MHz 0.38 dB max. (+35~+85℃)
0.28 dB max. (+15~+35℃)
0.28 dB max. (-20~+15℃)
Ripple 0.1 dB max. (699 - 746 MHz)
0.1 dB max. (791 - 862 MHz)
0.1 dB max. (824 - 960 MHz)
0.1 dB max. (1710 - 2170 MHz)
0.1 dB max. (2500 - 2690 MHz)
RF Coupling 28.1~29.5 dB (699MHz)
25.8~27.2 dB (915MHz)
20.7~22.1 dB (1710MHz)
19.9~21.3 dB (1880MHz)
19.3~20.7 dB (2025MHz)
18.3~19.7 dB (2300MHz)
17.1~18.5 dB (2690MHz)
Coupling ration missmatch between Coupler
branch 1 and Coupler branch 2 -1~1 dB (699 - 2690 MHz)
Directivity 18 dB min. (699 - 2690 MHz)
Impedance 50 Ω
FI 168K1687AA
Pass band frequency 698 - 2690 MHz
Insertion loss at 699 - 2690 MHz 0.25 dB max. (+25℃)
0.30 dB max. (-40~+85℃)
S11 Coupled port at 698 - 2690 MHz 0.25 dB max. (+25℃)
RF Coupling 26.5~29.0 dB (698MHz)
24.0~27.0 dB (915MHz)
21.5~24.5 dB (1710MHz)
21.5~24.5 dB (2025MHz)
21.5~24.5 dB (2300MHz)
21.5~25.5 dB (2690MHz)
Isolation 35 dB min. (698 - 2690 MHz)
Impedance 50 Ω
-50
-40
-30
-20
-10
0
0.5 1.0 1.5 2.0 2.5 3.0
Couple/Isolation[dB]
Frequency[GHz]
CPL
ISO
chipfilter_e-E07R01
157
19
1m fiflflf Sprocket hole \‘m :33 / Sprocket hole Base tape Chip cavity Battom tape / TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipfilter_pack_e-E07R01
MULTILAYER CERAMIC DEVICES / DIPLEXERS / COUPLER / 2 BRANCH COUPLER
PACKAGING
①Minimum Quantity
Type Embossed tape / Paper tape [pcs]
212B
3000
212C
212P
168B
4000
168L
168D
168P
168L-G 5000
168H
168W 8000
168K
105B 10000
105L
②Tape Material
Embossed Tape
Top tape
Base tape
Sprocket hole
Chip cavity
Card Board Cattier Tape
Top tape
Base tape
Sprocket hole
Bottom tape Chip cavity
Chip
Chip Filled
Taped package
Type Thickness
mm (inch) Standard Quantity [pcs]
212B 0.90 typ.(0.035)
3000
212C 0.90 typ.(0.035)
212P 0.90 typ.(0.035)
212C-0.7 0.60 typ.(0.024)
168B 0.45 typ.(0.018)
4000
168L-0.5 0.45 typ.(0.018)
168L-0.65 0.60 typ.(0.024)
168D 0.45 typ.(0.018)
168P 0.60 typ.(0.024)
168L-G 0.60 typ.(0.024) 5000
168H 0.60 typ.(0.024)
168W 0.45 typ.(0.018) 8000
168K 0.60 typ.(0.024)
105B 0.30 typ.(0.0118) 10000
105L 0.30 typ.(0.0118)
TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipfilter_pack_e-E07R01
③Taping Dimensions
Embossed tape 0.315 inches wide
F
2.0±0.05
(0.079±0.002)
4.0±0.1
(0.157±0.004)
1.75±0.1
(0.069±0.004)
3.5±0.05
(0.138±0.002)
8.0±0.3
(0.315±0.012)
φ1.5+0.1/-0
(φ0.059+0.004/-0)
Sprocket hole
A
B
Unit:mm(inch)
Type Chip cavity Insertion Pitch Tape Thickness max.
A B F K T
212B 1.55±0.2
(0.061±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
1.6
(0.063)
0.3
(0.012)
212C 1.55±0.2
(0.061±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
1.6
(0.063)
0.3
(0.012)
212C-0.7 1.55±0.2
(0.061±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
1.3
(0.051)
0.3
(0.012)
212P 1.55±0.2
(0.061±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
1.6
(0.063)
0.3
(0.012)
Unit:mm(inch)
Paper tape 0.315 inches wide
F
2.0±0.05
(0.079±0.002)
4.0±0.1
(0.157±0.004)
1.75±0.1
(0.069±0.004)
3.5±0.05
(0.138±0.002)
8.0±0.3
(0.315±0.012)
φ1.5+0.1/-0
(φ0.059+0.004/-0)
Sprocket hole
A
B
T
Unit:mm(inch)
Type Chip cavity Insertion Pitch Tape Thickness max.
T
168B 1.00±0.05
(0.039±0.002)
1.80±0.05
(0.071±0.002)
4.0±0.1
(0.157±0.004)
0.55
(0.022)
168L 1.00±0.05
(0.039±0.002)
1.80±0.05
(0.071±0.002)
4.0±0.1
(0.157±0.004)
0.55
(0.022)
168W 1.00±0.05
(0.039±0.002)
1.80±0.05
(0.071±0.002)
4.0±0.1
(0.157±0.004)
0.55
(0.022)
168K 1.00±0.05
(0.039±0.002)
1.80±0.05
(0.071±0.002)
4.0±0.1
(0.157±0.004)
0.80
(0.031)
168D 1.00±0.05
(0.039±0.002)
1.80±0.05
(0.071±0.002)
4.0±0.1
(0.157±0.004)
0.55
(0.022)
168P 0.95±0.05
(0.037±0.002)
1.80±0.05
(0.071±0.002)
4.0±0.1
(0.157±0.004)
0.80
(0.031)
168L-G 0.95±0.05
(0.037±0.002)
1.80±0.05
(0.071±0.002)
4.0±0.1
(0.157±0.004)
0.80
(0.031)
168H 0.95±0.05
(0.037±0.002)
1.80±0.05
(0.071±0.002)
4.0±0.1
(0.157±0.004)
0.80
(0.031)
105B 0.62±0.03
(0.024±0.001)
1.12±0.03
(0.044±0.001)
2.0±0.05
(0.079±0.002)
0.45
(0.018)
105L 0.62±0.03
(0.024±0.001)
1.12±0.03
(0.044±0.001)
2.0±0.05
(0.079±0.002)
0.45
(0.018)
Unit:mm(inch)
Blank pomons cmu cawly Blank Demons Leads! 0 OS]: :7 c d\\r> \\ Em DIV IEKLD ’/ “mammal“; 100mlnormure| [1 57 w ch m ma'e) US? men or more) 400mm 0! more (15,7 men or more: Dwacuon 0| Iape med PuH directionJ Top cover lane E 352 tape TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipfilter_pack_e-E07R01
④Leader and Blank Portion
⑤Reel size
E
C
D
R B
t
A
W
A B C D E R
φ178±2.0
(φ7.01±0.079)
φ50min.
(φ1.97 min.)
φ13.0±0.2
(φ0.512±0.008)
φ21.0±0.8
(φ0.827±0.031)
2.0±0.5
(0.079±0.020) 1.0
t W
8mm width tape
(0.315 inches width)
2.5max.
(0.098max.)
10±1.5
(0.394±0.059)
12mm width tape
(0.472 inches width)
2.5max.
(0.098max.)
14±1.5
(0.551±0.059)
Unit:mm(inch)
⑥Top Tape Strength
The top tape requires a peel-off force of 0.1~0.7N in the direction of the arrow as illustrated below.
Homes Jlg CIoss—sechu'\ TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipfilter_reli_e-E07R01
MULTILAYER CERAMIC DEVICES / DIPLEXERS / COUPLER / 2 BRANCH COUPLER
RELIABILITY DATA
1. Operating Temperature Range
Specified Value -30~+85℃
2. Storage Temperature Range
Specified Value -30~+85℃
Test Methods and
Remarks ※Note : -20 to +40℃ in taped packaging
3. Resistance to Flexure of Substrate
Specified Value No mechanical damage.
Test Methods and
Remarks
Warp : 2mm
Testing board : Glass epoxy-resin substrate
Thickness : 0.8mm
4. Adhesion of Electrode
Specified Value Characteristics : shall satisfy the electrical characteristics.
Appearance : No significant abnormality.
Test Methods and
Remarks
Applied force : 5N
Duration : 10 sec.
5. Solderability
Specified Value 75% or more of immersed surface of terminal electrode shall be covered with fresh solder.
Test Methods and
Remarks
Solder temperature : 230±5℃
Duration : 4±1 sec
Preconditioning : Immersion into flux.
Immersion and Removal speed : 25mm/sec.
6. Resistance to Solder Heat
Specified Value Characteristics : shall satisfy the electrical characteristics.
Appearance : No significant abnormality.
Test Methods and
Remarks
Preheating : 150℃ for 2 min.
Solder temperature : 260±5℃
Duration : 5±0.5 sec.
Preconditioning : Immersion into flux.
Immersion and Removal speed : 25mm/sec.
Recovery : 2 to 3hrs of recovery under the standard condition after the removal from test chamber.
TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipfilter_reli_e-E07R01
7. Thermal Shock
Specified Value Characteristics : shall satisfy the electrical characteristics.
Appearance : No significant abnormality.
Test Methods and
Remarks
According to JIS C60068-2-14.
Conditions for 1 cycle
Step Temperature (℃) Duration (min)
1 -40±3 30±3
2 Room Temperature Within 3
3 85±2 30±3
4 Room Temperature Within 3
Number of cycles : 100
Mounting method : Soldering onto PC board.
Recovery : 2 to 3hrs of recovery under the standard condition after the removal from test chamber.
8. Humidity (steady state)
Specified Value Characteristics : shall satisfy the electrical characteristics.
Appearance : No significant abnormality.
Test Methods and
Remarks
Temperature : +40±2℃
Humidity : 90~95%RH
Duration : 96hrs
Recovery : 2 to 3hrs of recovery under the standard condition after the removal from test chamber.
9. High temperature life test
Specified Value Characteristics : shall satisfy the electrical characteristics.
Appearance : No significant abnormality.
Test Methods and
Remarks
Temperature : +85±2℃
Duration : 96hrs
Recovery : 2 to 3hrs of recovery under the standard condition after the removal from test chamber.
10. Low temperature life test
Specified Value Characteristics : shall satisfy the electrical characteristics.
Appearance : No significant abnormality.
Test Methods and
Remarks
Temperature : -40±2℃
Duration : 96hrs
Recovery : 2 to 3hrs of recovery under the standard condition after the removal from test chamber.
Note on standard condition:
"standard condition" referred to herein is defined as follows :
5 to 35℃ of temperature, 45 to 85% relative humidity and 86 to 106kPa of air pressure.
When there are questions concerning measurement result :
In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity and 86 to 106kPa of air
pressure.
Unless otherwise specified, all the tests are conducted under the "standard condition".
:c "a I, n so n‘au L—l an wn 605a: ‘ TAIYD YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipfilter_prec_e-E07R01
MULTILAYER CERAMIC DEVICES / DIPLEXERS / COUPLER / 2 BRANCH COUPLER
PRECAUTIONS
1. PCB Design
Technical
considerations
◆Land pattern design
Land pattern dimension examples
FI212B Type FI168B/L Type FI105B/L Type FI168L/H LGA Type
Unit:mm
Unit:mm
Unit:mm
0.25 0.25 0.25 0.250.40
0.60
Unit:mm
FI168D/FI168K Type FI212C Type FI168P Type FI212P Type
Unit:mm
Unit:mm
Unit:mm
Unit:mm
FI212P****G* Type FI168W Type
0.6500 0.3500
0.3500
0.5000
Unit:mm
Unit:mm
2. Soldering
Technical
considerations
◆Conditions for Reflow soldering (for reference)
【Reflow Profile】
Preheating 230℃
Within 10sec.
Slow cooling
60sec.
Min.
60sec
Min.
300
200
100
0
Temperature(℃)
Peak
260℃ Max.
Within 10sec.
Slow
cooling
Heating above
230℃
40sec. Max.
300
200
100
0
Temperature(℃)
Preheating150℃
60sec. Min.
Components should be preheated to within 100
to 130℃ from soldering temperature.
Assured to be reflow soldering for 2 times.
Note : The above profiles are the maximum
allowable soldering condition, therefore
these profiles are not always
recommended.
TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipfilter_prec_e-E07R01
3. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packaging material in good condition, care must be taken to control
temperature and humidity in the storage area. Humidity should especially be kept as low as possible.
Recommended conditions
Ambient temperature : -20~+40℃
Humidity : Below 70%RH
The ambient temperature must be kept below 30℃.
Even under ideal storage conditions, the solderbility of electrodes decreases gradually, so filters should be mounted within 6 months
from the time of delivery.
The packaging material should be kept where no chlorine or sulfur exists in the air.
Technical
considerations
◆Storage
1. If the parts are stocked in a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of
terminal electrodes and deterioration of taping/ packaging materials may take place. For this reason, components should be used within 6
months from the time of delivery. If exceeding the above period, please check the solderability before using the filter.
Please contact of our offices for further details of specifications.
All of the standard values listed here are subject to change without notice.
Therefore, please check the specifications carefully before use.

Products related to this Datasheet

RF FILTER LOW PASS 2.45GHZ 0402
Available Quantity: 18,777
Unit Price: 1.16
RF FILTER LOW PASS 1.81GHZ 0402
Available Quantity: 5,582
Unit Price: 1.16
RF FILTER BAND PASS 2.45GHZ 0805
Available Quantity: 28,963
Unit Price: 1.29
RF DIPLEXER 1.584/5.425GHZ 0603
Available Quantity: 8,925
Unit Price: 1.29
RF FILTER BAND PASS 2.45GHZ 0603
Available Quantity: 7,727
Unit Price: 1.19
RF DIPLEXER 892MHZ/1.94GHZ 2012
Available Quantity: 1,510
Unit Price: 1.56
RF FILTER LOW PASS 1.34GHZ 0603
Available Quantity: 1,280
Unit Price: 1.22
RF DIPLEXER 892MHZ/1.94GHZ 2012
Available Quantity: 1,133
Unit Price: 1.56
RF FILTER BAND PASS 2.45GHZ 0402
Available Quantity: 10,832
Unit Price: 1.06
RF DIPLEXER 829MHZ/4.692GHZ 0805
Available Quantity: 430
Unit Price: 1.47
RF FILTER BANDPASS 1.907GHZ 0805
Available Quantity: 3,398
Unit Price: 1.29
RF DIR CPLR 699MHZ-2.69GHZ 0603
Available Quantity: 304
Unit Price: 1.08
RF DIPLEXER 829MHZ/1.584GHZ 0805
Available Quantity: 87
Unit Price: 1.47
RF DIPLEXER 829MHZ/2.055GHZ 0805
Available Quantity: 45
Unit Price: 1.47
RF DIPLEXER 829MHZ/1.584GHZ 0805
Available Quantity: 24
Unit Price: 1.47
RF FILTER BAND PASS 2.45GHZ 0805
Available Quantity: 0
Unit Price: 0
RF FILTER BALANCE 2.45GHZ 0805
Available Quantity: 0
Unit Price: 0
RF FILTER LOW PASS 620MHZ 0805
Available Quantity: 0
Unit Price: 0
RF FILTER BALANCE 2.45GHZ 0805
Available Quantity: 0
Unit Price: 0
RF FILTER BANDPASS 2.593GHZ 0603
Available Quantity: 0
Unit Price: 0
RF FILTER BANDPASS 2.593GHZ 0603
Available Quantity: 0
Unit Price: 0
RF FILTER BAND PASS 3.96GHZ 0805
Available Quantity: 0
Unit Price: 0
RF FILTER BANDPASS 4.488GHZ 0805
Available Quantity: 0
Unit Price: 0
RF FILTER LOW PASS 620MHZ 0805
Available Quantity: 0
Unit Price: 0
RF FILTER LOW PASS 615MHZ 0805
Available Quantity: 0
Unit Price: 0
RF FILTER LOW PASS 610MHZ 0805
Available Quantity: 0
Unit Price: 0
RF FILTER LOW PASS 610MHZ 0805
Available Quantity: 0
Unit Price: 0
RF FILTER LOW PASS 638MHZ 0805
Available Quantity: 0
Unit Price: 0
RF FILTER LOW PASS 620MHZ 0603
Available Quantity: 0
Unit Price: 0
RF FILTER LOW PASS 1.585GHZ 0603
Available Quantity: 0
Unit Price: 0
FILTER BALANCE 2.4GHZ BLUETOOTH
Available Quantity: 0
Unit Price: 0
BALUN 2.4GHZ-2.5GHZ 0805
Available Quantity: 0
Unit Price: 0
RF FILTER BALANCE 2.45GHZ 0805
Available Quantity: 0
Unit Price: 0
RF FILTER BALANCE 2.45GHZ 0805
Available Quantity: 0
Unit Price: 0
RF FILTER BALANCE 2.495GHZ 0805
Available Quantity: 0
Unit Price: 0
RF DIPLEXER 5.025/5.6475GHZ MOD
Available Quantity: 0
Unit Price: 0
RF FILTER BAND PASS 2.5GHZ 0603
Available Quantity: 0
Unit Price: 0
RF FILTER BAND PASS 2.45GHZ 0805
Available Quantity: 0
Unit Price: 0
RF FILTER BAND PASS 2.45GHZ 0805
Available Quantity: 3,000
Unit Price: 1.29
RF FILTER BALANCE 2.45GHZ 0805
Available Quantity: 0
Unit Price: 0
BALUN 5.725-5.85GHZ 50/100 0603
Available Quantity: 0
Unit Price: 0
RF DIPLEXER 2.45GHZ/5.51GHZ 0603
Available Quantity: 0
Unit Price: 0
BALUN 900MHZ-2.2GHZ 50/75 0603
Available Quantity: 0
Unit Price: 0
RF FILTER BANDPASS HI MULTI 0603
Available Quantity: 0
Unit Price: 0
RF DIPLEX 824.5MHZ/1.94GHZ 0805
Available Quantity: 0
Unit Price: 0
RF DIPLEX 824.5MHZ/1.94GHZ 0603
Available Quantity: 0
Unit Price: 0
RF DIPLEXER 892MHZ/1.584GHZ 0603
Available Quantity: 4,000
Unit Price: 1.29
RF DIPLEXER 892MHZ/1.584GHZ 0603
Available Quantity: 4,000
Unit Price: 1.29
RF FILTR BANDPASS 1.6945GHZ 0603
Available Quantity: 0
Unit Price: 1.15