NHD-0216K3Z-FS(RGB)-FBW-V3 Datasheet by Newhaven Display Intl

View All Related Products | Download PDF Datasheet
Newhaven Display International, Inc. www.newhavendisglay.com nhtech@newhavendisplayxom nhsales@newhavendisplav.com
NHD-0216K3Z-FS(RGB)-FBW-V3
Serial Liquid Crystal Display Module
NHD- Newhaven Display
0216- 2 Lines x 16 Characters
K3Z- Model
F- Transflective
S(RGB)- Side LED Backlights (Red-Green-Blue)
F- FSTN Positive
B- 6:00 Optimal View
W- Wide Temperature
V3- Firmware Version 3.00
RoHS Compliant
Newhaven Display International, Inc.
2661 Galvin Ct.
Elgin IL, 60124
Ph: 847-844-8795 Fax: 847-844-8796
www.newhavendisplay.com
nhtech@newhavendisplay.com nhsales@newhavendisplay.com
Document Revision History Revision Date Description Changed by 0 5/16/12 Initial Release SB 1 10/1/12 Character address code updated AK 2 5/30/13 Electrical characteristics updated, RGB backlight note added AK in command table 3 1/28/16 Module Redesign SB 4 12/29/16 Backlight & PCB Redesign SB 5 9/11/18 Supply Current, Backlight Voltage & IZC Speed Updated SB RGB Color Chart Added 6 6/11/19 SPI & Self-Test Information Updated SB
[2]
Document Revision History
Revision
Date
Description
Changed by
0
5/16/12
Initial Release
SB
1
10/1/12
Character address code updated
AK
2
5/30/13
Electrical characteristics updated, RGB backlight note added
in command table
AK
3
1/28/16
Module Redesign
SB
4
12/29/16
Backlight & PCB Redesign
SB
5
9/11/18
Supply Current, Backlight Voltage & I2C Speed Updated
RGB Color Chart Added
SB
6
6/11/19
SPI & Self-Test Information Updated
SB
Functions and Features
2 lines x 16 characters
Red/Green/Blue LED backlights
Serial Interface: I2C, SPI or RS-232(TTL)
+5.0V power supply
1/16 duty, 1/5 bias
5x8 pixels with cursor
RoHS Compliant
DDDDDK DDDDDK IDDDDDK IDDDDDK ' Newhlvln Duchy NHD-Il11SKal-FsrRGfil-FBW-VLVIVE wwvv Newhaven Dwsplay \nlemational NHD-0216K3Z :E |:l |:l|:l|:l|:l|:l|:l|:l|:l H AV E N i mm NTERNATI inlmm 10 inlmm A3 5 Ban 5 Ban mums» m w mwms mu com/18 09/14/13 N5 mmmammmm ©E DD m sum WWW; THIS DRAWWG IS 5mm mg PROPERTV or NEWHAVEN DISPLAY WTERNAT‘ONAL, INC
C
B
A
D
E
F
C
B
A
D
E
F
4321 8765
4321 8765
CHECKED BY:
DRAW N DATE:
09/14/18
SHEET 1 OF 1
- THIRD ANGLE PROJECTION
DRAWING/PART NUMBER:
STANDARD TOLERANCES
(UNLESS OTHERWISE SPECIFIED)
LINEAR:
XX.
XX.X
XX.XX
UNLESS OTHERWISE SPECIFIED
NHD-0216K3Z-FS(RGB)-FBW-V3
REVISION:
1.0
SIZE:
A3
SCALE:
DRAW N BY:
S. Baxi
CHECKED DATE:
THIS DRAWING IS SOLELY THE PROPERTY OF NEWHAVEN DISPLAY INTERNATIONAL, INC.
THE INFORMATION IT CONTAINS IS NOT TO BE DISCLOSED, REPRODUCED OR COPIED IN
WHOLE OR PART WITHOUT WRITTEN APPROVAL FROM NEWHAVEN DISPLAY.
±0.3 mm
±0.3 mm
±0.3 mm
- DIMENSIONS ARE IN MILLIMETERS
SYMBOL REVISION DATE
DO NOT SCALE DRAWING
S. Baxi
09/14/18
APPROVED BY:
APPROVED DATE:
09/14/18
S. Baxi
Notes:
1. Driver: 1/16 Duty, 1/5 Bias
2. Voltage: 5.0V VDD
3. Display Mode: FSTN Posi�ve / Transflec�ve
4. Op�mal View: 6:00
5. Backlight: Red, Blue & Green LED Backlight
6. Driver IC: PIC16F690 & ST7066U
7. Interface: RS232 (TTL) / SPI / I2C
Injec�on Port
11: Pln Na. Symbnl External Connectlon Functlon Descrlptlon 1 RX MPU RS-232 lTl’Ll Serial input pon 2 v Power Supply Ground 3 V Power Supply Supply Voltage for Logic (+5.0\/) 12: Pln Na. Symbnl External Connectlon Functlon Descrlptlon 1 SPISS MPU SPl Slave Select (NC in |2C mode) 2 SDO NC No Connect 3 SCK/SCL MPU Serial Clock 4 SDI/SDA MPU Serial Data In lSPl) / Serial Data (IZC) 5 V Power Supply Ground 5 V Power Supply Supply Voltage for Logic (+5.0\/) 13: Pln Na. Symbnl External Connectlon Functlon Descrlptlon 1 K Power Supply Eacklight Common Cathode [Ground) 2 A-RED Power Supply Red LED Anode (zvov) 3 A-GREEN Power Supply Green LED Anode 13.0w 4 A-BLUE Power Supply Blue LED Anode 13.0w R B Jumper Communication Selection R1 R2 Protocol Descrlptlon Short Short TEST Self-test Open Short SPI IOOKHZ max clock Short Open IZC SOKHZ max clock Open Open RS-232 5V, TI’L signal
[4]
Pin Description
J1:
Pin No.
Symbol
External Connection
Function Description
1
RX
MPU
RS-232 (TTL) Serial input port
2
V
SS
Power Supply
Ground
3
VDD
Power Supply
Supply Voltage for Logic (+5.0V)
J2:
Pin No.
Symbol
External Connection
Function Description
1
SPISS
MPU
SPI Slave Select (NC in I2C mode)
2
SDO
NC
No Connect
3
SCK/SCL
MPU
Serial Clock
4
SDI/SDA
MPU
Serial Data In (SPI) / Serial Data (I2C)
5
VSS
Power Supply
Ground
6
VDD
Power Supply
Supply Voltage for Logic (+5.0V)
J3:
Pin No.
Symbol
External Connection
Function Description
1
K
Power Supply
Backlight Common Cathode (Ground)
2
A-RED
Power Supply
Red LED Anode (2.0V)
3
A-GREEN
Power Supply
Green LED Anode (3.0V)
4
A-BLUE
Power Supply
Blue LED Anode (3.0V)
Recommended LCD connector: 2.54mm pitch pins on P1 or P2
Backlight connector: controlled by command Mates with: -
Jumper Communication Selection
R1
R2
Protocol
Description
Short
Short
TEST
Self-test
Open
Short
SPI
100KHz max clock
Short
Open
I2C
50KHz max clock
Open
Open
RS-232
5V, TTL signal
Electrical Characteristics Item Symbol Candltlan Min. Typ. Max. Unit Operating Temperature Range T - -2o - +70 °C Storage Temperature Range T - -3o - +80 °C Supply Voltage v - 4.5 5.0 5.5 v Supply Current lLCD) l 1.4 4.2 5.3 mA Supply for LCD leontrast) VDD-V 4.0 4.3 4.5 v "H“ Level input V - 0.8 * V - V V “L“ Level input V - V - 0.2 *V V Backllgnt Supply Current , Red | - - 1o 15 mA Backllgnt Supply VoltageeRed v I : 10 mA 1.7 1.9 2.1 v Backllgnt Supply Current , Green | - - 15 20 mA Backllgnt Supply Voltageeereen v I :15 mA 2.7 2.9 3.1 v Backllgnt Supply Current , Blue | - - 15 20 mA Backllgnt Supply Voltageealue v I :15 mA 2.7 2.9 3.1 v 5 Optical Characteristics Item Symbol Candltlan Mln. Typ. Max. Unlt Top ow - 15 - ° Bottom ov- - 45 - ° Left ex- - 45 - a Right ex+ - 45 - ° Contrast Ratio CR - 3 5 - - Rise T - 200 300 ms Fall T - 250 350 ms X - 0.67 0.70 0.73 V - 0.27 0.30 0.33 X - 0.13 0.16 0.19 V - 0.72 0.75 0.78 X - 0.11 0.14 0.17 V - 0.05 0.08 0.11 http: www.newhavendisplav.c0m app notes P|C16F690.pdf
[5]
Electrical Characteristics
Item
Symbol
Condition
Min.
Typ.
Max.
Unit
Operating Temperature Range
TOP
-
-20
-
+70
C
Storage Temperature Range
TST
-
-30
-
+80
C
Supply Voltage
VDD
-
4.5
5.0
5.5
V
Supply Current (LCD)
I
DD
VDD = 5.0V
T
OP
= 25°C
1.4
4.2
6.3
mA
Supply for LCD (contrast)
VDD-V0
4.0
4.3
4.6
V
H Level input
VIG
-
0.8 * VDD
-
VDD
V
L Level input
VIL
-
VSS
-
0.2 * VDD
V
Backlight Supply Current Red
ILED
-
-
10
15
mA
Backlight Supply Voltage Red
VLED
ILED = 10 mA
1.7
1.9
2.1
V
Backlight Supply Current Green
ILED
-
-
15
20
mA
Backlight Supply Voltage Green
V
LED
I
LED
= 15 mA
2.7
2.9
3.1
V
Backlight Supply Current Blue
ILED
-
-
15
20
mA
Backlight Supply Voltage Blue
VLED
ILED = 15 mA
2.7
2.9
3.1
V
*The LED of the backlight is driven by current; drive voltage is for reference only. Drive voltage must be selected to ensure backlight current drain is below MAX level
stated.
Optical Characteristics
Item
Symbol
Condition
Min.
Typ.
Max.
Unit
Optimal
Viewing
Angles
Top
ϕY+
CR 3
-
15
-
Bottom
ϕY-
-
45
-
Left
θX-
-
45
-
Right
θX+
-
45
-
Contrast Ratio
CR
-
3
5
-
-
Response Time
Rise
TR
TOP = 25°C
-
200
300
ms
Fall
TF
-
250
350
ms
Color Chart
Coordinates
Red
XR
-
0.67
0.70
0.73
YR
-
0.27
0.30
0.33
Green
XG
-
0.13
0.16
0.19
YG
-
0.72
0.75
0.78
Blue
XB
-
0.11
0.14
0.17
YB
-
0.05
0.08
0.11
Controller Information
Built-in PIC16F690 controller.
Please download specification at http://www.newhavendisplay.com/app_notes/PIC16F690.pdf
[6]
Communication Information
This display uses a built-in PIC16F690 for serial communication.
100mS delay is required upon power-up for the built-in PIC to initialize the display controller.
I2C protocol:
To enter the I2C mode, place a jumper on R1.
SDA and SDK have pull-up resistors (10K Ohm) on R7 and R8.
The default I2C address is 80 (50 hex). The I2C address can be changed to any 8-bit value by command function, with
the exception that the LSB (least significant bit) must always be ‘0’. Once the I2C address has been changed, it will be
saved in the system memory, and it will revert back to the default address if either RS-232 or SPI protocol is selected.
The I2C interface can receive data at up to 50KHz clock rate.
SPI protocol:
To enter the SPI mode, place a jumper on R2.
SPI mode has a normally high idle clock. When Slave Select is LOW, data is sampled on the rising edge of the Clock.
The SPI interface can receive data at up to 100KHz clock rate.
SPI Mode 3
CPOL = 1
CPHA = 1
RS-232 (TTL) protocol:
To enter the RS-232 mode, both R1 and R2 should be open.
The RS-232 signal must be 5V TTL compatible. Communication format is 8-bit data, 1 Stop bit, no parity, no handshaking.
Default BAUD rate is 9600 and is changeable with a command function. Once the BAUD rate has been changed, it will be
saved in the system memory, and it will revert to the default address if either I2C or SPI protocol is selected.
Self-Test Mode
To enter self-test mode, both R1 and R2 should be populated with a 0Ω resistor.
In self-test mode the backlight will be turned on and set to high, the contrast will be set to nominal value. Then the
display returns the following screens:
Screen 1:
- Newhaven Display
Screen 2:
- Firmware Version 3.0
Screen 3:
- Default baud rate: 9600
- Default I2C Slave Address: 0x50
ASCII Text
To display normal text, just enter its ASCII number. A number from 0x00 to 0x07 displays the user defined custom
character, 0x20 to 0x7F displays the standard set of characters, 0xA0 to 0xFD display characters and symbols that are
factory-masked on the ST7066U controller. 0xFE is reserved.
Prefix Command Parameter Description Execution time - - 1 Byte Display Character Write (0x00 N OxFF) 100uS OxFE 0x41 None Display on 100uS OxFE 0x42 None Display off 100uS OxFE 0x45 1 Byte Set cursor 100uS OxFE 0x46 None Cursor home 1.5mS OxFE 0x47 None Underline cursor on 1.5mS OxFE 0x48 None Underline cursor off 1.5mS OxFE 0x49 None Move cursor left one place 100uS OxFE OXAA None Move cursor right one place 100uS OxFE Ox4B None Blinking cursor on 100uS OxFE Ox4C None Blinking cursor of‘f 100uS OxFE 0x4E None Backspace 100uS OxFE 0x51 None Clear screen 1.5mS OxFE 0x52 1 Byte Set contrast SOOuS OxFE 0x53 1 Byte Set backlight brightness* 100uS OxFE 0x54 9 Byte Load custom character ZOOuS OxFE 0x55 None Move display one place to the left 100uS OxFE 0x56 None Move display one place to the right 100uS OxFE 0x61 1 Byte Change RS-232 BAUD rate 3mS OxFE 0x62 1 Byte Change IZC address 3mS OxFE 0x70 None Display firmware version number 4mS OxFE 0x71 None Display RS-232 BAUD rate 10mS OxFE 0x72 None Display IZC address 4mS ave es Parameter Length Description
[7]
Table of Commands
Prefix
Command
Parameter
Description
Execution time
-
-
1 Byte
Display Character Write (0x00 ~ 0xFF)
100uS
0xFE
0x41
None
Display on
100uS
0xFE
0x42
None
Display off
100uS
0xFE
0x45
1 Byte
Set cursor
100uS
0xFE
0x46
None
Cursor home
1.5mS
0xFE
0x47
None
Underline cursor on
1.5mS
0xFE
0x48
None
Underline cursor off
1.5mS
0xFE
0x49
None
Move cursor left one place
100uS
0xFE
0x4A
None
Move cursor right one place
100uS
0xFE
0x4B
None
Blinking cursor on
100uS
0xFE
0x4C
None
Blinking cursor off
100uS
0xFE
0x4E
None
Backspace
100uS
0xFE
0x51
None
Clear screen
1.5mS
0xFE
0x52
1 Byte
Set contrast
500uS
0xFE
0x53
1 Byte
Set backlight brightness*
100uS
0xFE
0x54
9 Byte
Load custom character
200uS
0xFE
0x55
None
Move display one place to the left
100uS
0xFE
0x56
None
Move display one place to the right
100uS
0xFE
0x61
1 Byte
Change RS-232 BAUD rate
3mS
0xFE
0x62
1 Byte
Change I2C address
3mS
0xFE
0x70
None
Display firmware version number
4mS
0xFE
0x71
None
Display RS-232 BAUD rate
10mS
0xFE
0x72
None
Display I2C address
4mS
* = N/A for RGB models
Changing the I2C Slave Address
Syntax hexadecimal 0xFE 0x62 [addr]
Parameter Parameter Length Description
[addr] 1 byte New I2C address, 0x00 0xFE
The LSB is always ‘0’.
Description This command sets the I2C address. The address must be an even number (LSB = 0). The
address change requires 20 microseconds to take effect; therefore, the subsequent input
must have an appropriate delay. The default I2C address can be restored if SPI or RS-232
is selected as the communication mode.
Default: 0x50
h c 0 0 [ Parameter Length Description Thi BA ef B p Parameter BAUD 1 300 2 1200 3 2400 4 9600 5 14400 6 19.2K 7 57.6K 8 115.2K h c 0 0 Parameter Length Description h c 0 0 Parameter Length Description
[8]
Changing BAUD Rate
Syntax hexadecimal 0xFE 0x61 [baud]
Parameter Parameter Length Description
[BAUD] 1 byte New RS-232 BAUD Rate, 1 - 8
Description This command sets the RS-232 BAUD rate. The single byte parameter selects the desired
BAUD rate as in the table below. The new BAUD rate requires 20 microseconds to take
effect; therefore, the subsequent input must have an appropriate delay. The default
BAUD rate can be restored if I2C or SPI is selected as the communication mode. Illegal
parameter input will be discarded.
Parameter
BAUD
1
300
2
1200
3
2400
4
9600
5
14400
6
19.2K
7
57.6K
8
115.2K
Default: 9600 BAUD
Turn On Display
Syntax hexadecimal 0xFE 0x41
Parameter Parameter Length Description
None None Turn on LCD screen
Description This command turns on the LCD display screen. The display text is not altered.
Default: LCD screen is on
Turn Off Display
Syntax hexadecimal 0xFE 0x42
Parameter Parameter Length Description
None None Turn off LCD screen
Description This command turns off the LCD display screen. The display text is not altered.
Default: LCD screen is on
h c 0 0 [po Parameter Length Description Column 1 Column 16 Line 1 0x00 OXOF Line 2 0x40 0x4F h c 0 0 Parameter Length Description urs h c 0 0 Parameter Length Description Curs h c 0 0 Parameter Length Description
[9]
Set Cursor Position
Syntax hexadecimal 0xFE 0x45 [pos]
Parameter Parameter Length Description
[pos] 1 byte Put cursor at location specified by [pos], 0x00 to 0x67
Description This command moves the cursor to a specified location where the next character will be
displayed. The typical cursor position for a 2-line 16-character display is show below; a
cursor position outside these ranges will not be viewable.
Column 1
Column 16
Line 1
0x00
0x0F
Line 2
0x40
0x4F
Default: After a reset, the cursor is on position 0x00
Home Cursor
Syntax hexadecimal 0xFE 0x46
Parameter Parameter Length Description
None None Position cursor at line 1 column 1
Description This command moves the cursor to line 1, column 1 of the LCD screen. The display text is
not altered.
Default: None
Turn On Underline Cursor
Syntax hexadecimal 0xFE 0x47
Parameter Parameter Length Description
None None Turn on underline cursor
Description This command turns on the underline cursor.
Default: Underline cursor is off
Turn Off Underline Cursor
Syntax hexadecimal 0xFE 0x48
Parameter Parameter Length Description
None None Turn off underline cursor
Description This command turns off the underline cursor.
Default: Underline cursor is off
h c 0 0 Parameter Length Description ne e h c 0 0 Parameter Length Description or h c 0 0 Parameter Length Description so h c 0 0 Parameter Length Description
[10]
Move Cursor Left One Space
Syntax hexadecimal 0xFE 0x49
Parameter Parameter Length Description
None None Move cursor left 1 space
Description This command moves the cursor position left 1 space whether the cursor is turned on or
not. The displayed character is not altered.
Default: None
Move Cursor Right One Space
Syntax hexadecimal 0xFE 0x4A
Parameter Parameter Length Description
None None Move cursor right 1 space
Description This command moves the cursor position left 1 space whether the cursor is turned on or
not. The displayed character is not altered.
Default: None
Turn On Blinking Cursor
Syntax hexadecimal 0xFE 0x4B
Parameter Parameter Length Description
None None Turn on the blinking cursor
Description This command turns on the blinking cursor.
Default: The blinking cursor is off
Turn Off Blinking Cursor
Syntax hexadecimal 0xFE 0x4C
Parameter Parameter Length Description
None None Turn off the blinking cursor
Description This command turns off the blinking cursor.
Default: The blinking cursor is off
h c 0 Parameter Length Description h c 0 Parameter Length Description h c 0 [ 5 Parameter Length Description es h c 0 [ n Parameter Length Description
[11]
Back Space
Syntax hexadecimal 0xFE 0x4E
Parameter Parameter Length Description
None None Move cursor back one space, delete last character.
Description This command is destructive backspace. The cursor is moved back one space and the
character on the cursor is deleted.
Default: None
Clear Screen
Syntax hexadecimal 0xFE 0x51
Parameter Parameter Length Description
None None Clear LCD and move cursor to line 1 column 1.
Description This command clears the entire display and place the cursor at line 1 column 1.
Default: None
Set Display Contrast
Syntax hexadecimal 0xFE 0x52 [contrast]
Parameter Parameter Length Description
[contrast] 1 byte Set the display contrast, value between 1 and 50
Description This command sets the display contrast. The contrast setting can be between 1 and 50,
where 50 is the highest contrast.
Default: 40
Set Backlight Brightness
Syntax hexadecimal 0xFE 0x53 [brightness]
Parameter Parameter Length Description
[brightness] 1 byte Set the backlight brightness level, value between 1 and 8
Description This command sets the backlight brightness level. The value can be between 1 and 8.
Default: 8
0 [ [ Parameter Length Description Bit 7 6 5 4 3 2 1 0 Hex Byte 1 O O 0 0 0 1 O 0 0x04 Byte Z O O 0 0 0 O O 0 0x00 Byte 3 O O 0 0 0 1 O 0 0x04 Byte 4 O O 0 0 1 O O 0 0x08 Byte 5 O O 0 1 0 O O 0 0x10 Byte 6 O O 0 1 0 O O 1 0x11 Byte 7 O O 0 0 1 1 1 0 OXOE Byte 8 O O 0 0 0 O O 0 0x00 Left h c 0 Parameter Length Description gh h c 0 Parameter Length Description
[12]
Load Custom Characters
Syntax hexadecimal 0xFE 0x54 [addr] [d0 …d7]
Parameter Parameter Length Description
[addr] 1 byte Custom character address, 0 – 7
[D0...D7] 8 bytes Custom character pattern bit map
Description There is space for eight user-defined custom characters. This command loads the custom
character into one of the eight locations. The custom character pattern is bit mapped
into 8 data bytes. The bit map for Spanish character ‘¿’ is shown in table below. To
display the custom character, user has to enter the address of the character (0 to 8).
Bit
7
6
5
4
3
2
1
0
Hex
Byte 1
0
0
0
0
0
1
0
0
0x04
Byte 2
0
0
0
0
0
0
0
0
0x00
Byte 3
0
0
0
0
0
1
0
0
0x04
Byte 4
0
0
0
0
1
0
0
0
0x08
Byte 5
0
0
0
1
0
0
0
0
0x10
Byte 6
0
0
0
1
0
0
0
1
0x11
Byte 7
0
0
0
0
1
1
1
0
0x0E
Byte 8
0
0
0
0
0
0
0
0
0x00
Default: None
Shift Display to the Left
Syntax hexadecimal 0xFE 0x55
Parameter Parameter Length Description
None None Shift the LCD screen to the left 1 space.
Description This command shifts the display to the left 1 space. The cursor position also moves with
the display, and the display data is not altered.
Default: None
Shift Display to the Right
Syntax hexadecimal 0xFE 0x56
Parameter Parameter Length Description
None None Shift the LCD screen to the right 1 space.
Description This command shifts the display to the right 1 space. The cursor position also moves
with the display, and the display data is not altered.
Default: None
si um Parameter Length Description Ra Parameter Length Description Parameter Length Description lization Program http: www.newhavendisplay.c0m app notes Seriai LCD.txt
[13]
Display Firmware Version Number
Syntax hexadecimal 0xFE 0x70
Parameter Parameter Length Description
None None Display the firmware version number.
Description This command displays the firmware version.
Default: None
Display RS-232 Baud Rate
Syntax hexadecimal 0xFE 0x71
Parameter Parameter Length Description
None None Display Baud Rate
Description This command displays the RS-232 BAUD rate.
Default: None
Display I2C Address
Syntax hexadecimal 0xFE 0x72
Parameter Parameter Length Description
None None Display I2C Address
Description This command displays the current I2C slave address.
Default: None
Example Initialization Program
See program code at http://www.newhavendisplay.com/app_notes/Serial_LCD.txt
m ... .u- E .... _H... mum r... n E u... ...“. _.n H + mfi m. ...u :d E: _..”. Hr E _un 0.21.. ... 1.1.5." w... i. _H :n. T... ..H -..". E ... 1 E g... H... ...I.. n. .... .n. a mm... .+. m... .T -... . m ...”. ...... -... ..n : w... H _... w _.r. .... .... n u 1.. .1.” r. kw. _ . .... a. E .3 H. m I 1| .I. . I 3... m... ..I h... ml“ +1. m.- 1 5.. H. I r- _ u. I : - . .a r n - _.. .1! u - -: l W m P a. P 5 T... u" n". m” “a” u. I .-... T. T... .._.. + m... a .- _... -n. e 1.... a. r.“ .1 ...... .1 m ”n n. WU. E - .. S T h _ u. -n H u. E T. ”a. __J T” _ mt“... rH -... C Wu __ F H. H I T... r...... _ .. ..1 _H_ mm. .1_2 1...an r... _.. .m. ... __H_ 9 .. ...... = _H.... ... w # ......+ _....wm .. T. ..-. ..... + m . m mmwmmmm@wm@mmmww@mm
[14]
Built-in Font Table
Quality Information Test Item Content of Test Test Condition Note Hign Temperature storage Endurance test applying tne nigh storage +80%, senrs 2 temperature for a long time. Low Temperature storage Endurance test applying tne law storage -30°c, 96hrs 1,2 temperature for a long time. Hign Temperature Endurance test applying tne electric stress +7o°c 96hrs 2 (voltage a current) and stress for a long time. Low Temperature Endurance test applying tne electric stress -20°c, 96hrs 1,2 (voltage a current) and stress for a long time. Hign Temperature/ Endurance test applying tne electric stress +40%, 90% RH, 96hrs 1,2 (voltage a current) and tire nign thermal with high humidity stress for a longtime. Thermal Shock resistance Endurance test applying the electric stress -20°C,60min >> +25°C,5min >> (voltage a current) dunng +70°C,60m and high thermal stress. 15 cycles Vibration test Endurance test applying vibration to 10-100Hz , 2g Acceleration. 3 2 Hrsi x,v,2 Static electricity test Endurance test applying electric static discnarge. V5:800V, RS:1.5l<fl, cs:100pf="" one="" time="" n="" n="" n="" p="" for="" using="" lcds/lcms="" s="" www.newhavendiselaycomlsgecszerecautionsgdf="" warranty="" information="" and="" terms="" &="" conditio="" imp:="" ww.newhavendisplav.com="" index.php?main="" page="terms">
[15]
Quality Information
Test Item
Content of Test
Test Condition
Note
High Temperature storage
Endurance test applying the high storage
temperature for a long time.
+80C , 96hrs
2
Low Temperature storage
Endurance test applying the low storage
temperature for a long time.
-30C , 96hrs
1,2
High Temperature
Operation
Endurance test applying the electric stress
(voltage & current) and the high thermal
stress for a long time.
+70C 96hrs
2
Low Temperature
Operation
Endurance test applying the electric stress
(voltage & current) and the low thermal
stress for a long time.
-20C , 96hrs
1,2
High Temperature /
Humidity Operation
Endurance test applying the electric stress
(voltage & current) and the high thermal
with high humidity stress for a long time.
+40C , 90% RH , 96hrs
1,2
Thermal Shock resistance
Endurance test applying the electric stress
(voltage & current) during a cycle of low
and high thermal stress.
-20C,60min -> +25C,5min ->
+70⁰C,60min = 1 cycle
16 cycles
Vibration test
Endurance test applying vibration to
simulate transportation and use.
10-100Hz , 2g Acceleration.
2 Hrs in each of 3 directions
X,Y,Z
3
Static electricity test
Endurance test applying electric static
discharge.
VS=800V, RS=1.5kΩ, CS=100pF
One time
Note 1: No condensation to be observed.
Note 2: Conducted after 4 hours of storage at 25C, 0%RH.
Note 3: Test performed on product itself, not inside a container.
Precautions for using LCDs/LCMs
See Precautions at www.newhavendisplay.com/specs/precautions.pdf
Warranty Information and Terms & Conditions
http://www.newhavendisplay.com/index.php?main_page=terms

Products related to this Datasheet

LCD MOD 32DIG 16X2 TRANSFL R/G/B
Available Quantity: 611
Unit Price: 35.55